Fix Corsair K70 RGB PRO V2 direct lighting

The K70 RGB PRO V2 (1B1C:1BB3) was detected but never lit: it blanked
into software render mode and then fell back to its onboard effect.
Getting it working turned up five faults, three of which affect every
Corsair V2 device rather than just this keyboard.

Packet size is now read from the HID report descriptor before the first
write instead of being inferred from a reply. These devices come in a 64
byte and a 1024 byte flavour, and sending a short packet to a 1024 byte
endpoint stalls it until the device is power cycled, so the size has to
be known up front rather than after two short queries have gone out.

CORSAIR_V2_PACKET_SIZE was 1024 while pkt_sze reached 1025, so every
read using pkt_sze overran its stack buffer by a byte. The command
helpers now use pkt_sze against buffers of the corrected size.

The lighting resource probe ran before the device was placed in software
render mode, where the answer is meaningless, and treated any error as
"use resource 1". Devices that answer invalid or unsupported for
resource 1 want the alternate lighting resource, which takes RGB
triplets; this keyboard is one of them. The probe now runs after the
render mode switch and distinguishes a stale open handle from an
unsupported resource.

Direct lighting writes were sized from the keymap, which covers only the
keys that exist. The hardware expects its full slot count and ignores a
short write, so corsair_v2_device carries an optional hw_led_count and
the buffer map is padded to it. Set to 193 for this keyboard.

The keepalive thread wrote LEDs on its first pass, because
last_update_time was left at the clock epoch and so always read as older
than the update period. That raced detection on the same HID handle with
no locking, which both corrupted the transaction and could abort the
process. The clock is now started before the thread runs, device
transactions are serialised behind a mutex, and the thread is stopped
before Shutdown rather than after.

Also fixes an uninitialised stack buffer sent to the device during
setup, and widens the K70 RGB PRO matrix to 22 columns so the numpad
period key has a position in the layout instead of being dropped.

Verified on hardware: repeated colour changes apply and the device stays
responsive across runs.

Co-Authored-By: Claude Opus 5 <[email protected]>

AutoStart/AutoStart-Flatpak.cpp

@@ -0,0 +1,158 @@
+/*---------------------------------------------------------*\
+| AutoStart-Flatpak.cpp                                     |
+|                                                           |
+|   Autostart implementation for Linux via Flatpak Portal   |
+|                                                           |
+|   Adam Honse <[email protected]>      04 Sep 2026 |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include "AutoStart-Flatpak.h"
+#include <gio/gio.h>
+
+AutoStart::AutoStart(std::string name)
+{
+    InitAutoStart(name);
+}
+
+void AutoStart::InitAutoStart(std::string name)
+{
+    app_name = name;
+}
+
+bool AutoStart::CallBackgroundPortal(bool enable, const AutoStartInfo& autostart_info)
+{
+    GError*             error           = nullptr;
+    GDBusConnection*    connection      = g_bus_get_sync(G_BUS_TYPE_SESSION, nullptr, &error);
+
+    if(!connection)
+    {
+        if(error)
+        {
+            g_error_free(error);
+        }
+
+        return false;
+    }
+
+    /*-----------------------------------------------------*\
+    | FreeDesktop Background Portal parameters              |
+    \*-----------------------------------------------------*/
+    const char*         bus_name        = "org.freedesktop.portal.Desktop";
+    const char*         object_path     = "/org/freedesktop/portal/desktop";
+    const char*         interface_name  = "org.freedesktop.portal.Background";
+    const char*         method_name     = "RequestBackground";
+
+    /*-----------------------------------------------------*\
+    | Build the options dictionary (vardict) required by    |
+    | the Portal                                            |
+    \*-----------------------------------------------------*/
+    GVariantBuilder     options_builder;
+    g_variant_builder_init(&options_builder, G_VARIANT_TYPE_VARDICT);
+
+    /*-----------------------------------------------------*\
+    | Reason shown to the user in the system settings /     |
+    | permission prompt                                     |
+    \*-----------------------------------------------------*/
+    std::string         reason_str      = "Allow " + app_name + " to launch automatically at startup.";
+    g_variant_builder_add(&options_builder, "{sv}", "reason", g_variant_new_string(reason_str.c_str()));
+
+    /*-----------------------------------------------------*\
+    | Toggle the autostart feature state                    |
+    \*-----------------------------------------------------*/
+    g_variant_builder_add(&options_builder, "{sv}", "autostart", g_variant_new_boolean(enable));
+
+    if(enable)
+    {
+        /*-------------------------------------------------*\
+        | Pass command-line arguments to the background     |
+        | request                                           |
+        \*-------------------------------------------------*/
+        GVariantBuilder arg_builder;
+        g_variant_builder_init(&arg_builder, G_VARIANT_TYPE("as"));
+
+        /*-------------------------------------------------*\
+        | Add the primary executable path inside the        |
+        | Flatpak sandbox                                   |
+        \*-------------------------------------------------*/
+        g_variant_builder_add(&arg_builder, "s", GetExePath().c_str());
+
+        /*-------------------------------------------------*\
+        | Append any additional arguments provided by       |
+        | OpenRGB's autostart config                        |
+        \*-------------------------------------------------*/
+        if(!autostart_info.args.empty())
+        {
+            g_variant_builder_add(&arg_builder, "s", autostart_info.args.c_str());
+        }
+
+        GVariant*   commandline_args    = g_variant_builder_end(&arg_builder);
+        g_variant_builder_add(&options_builder, "{sv}", "commandline", commandline_args);
+    }
+
+    /*-----------------------------------------------------*\
+    | An empty string window handle is used since this is a |
+    | background configuration request                      |
+    \*-----------------------------------------------------*/
+    const char*     parent_window       = "";
+    GVariant*       options             = g_variant_builder_end(&options_builder);
+
+    /*-----------------------------------------------------*\
+    | Bundle parameters: (s a{sv}) -> Parent window handle, |
+    | Options dictionary                                    |
+    \*-----------------------------------------------------*/
+    GVariant*       parameters          = g_variant_new("(s@a{sv})", parent_window, options);
+    GVariant*       reply;
+
+    reply = g_dbus_connection_call_sync(connection, bus_name, object_path, interface_name, method_name, parameters, G_VARIANT_TYPE("(o)"), G_DBUS_CALL_FLAGS_NONE, -1, nullptr, &error);
+
+    g_object_unref(connection);
+
+    if(error)
+    {
+        g_error_free(error);
+        return false;
+    }
+
+    if(reply)
+    {
+        g_variant_unref(reply);
+        return true;
+    }
+
+    return false;
+}
+
+bool AutoStart::EnableAutoStart(AutoStartInfo autostart_info)
+{
+    return CallBackgroundPortal(true, autostart_info);
+}
+
+bool AutoStart::DisableAutoStart()
+{
+    return CallBackgroundPortal(false);
+}
+
+bool AutoStart::IsAutoStartEnabled()
+{
+    /*-----------------------------------------------------*\
+    | The FreeDesktop Background Portal does not provide a  |
+    | stateless status getter.  Sandbox permissions are     |
+    | securely managed and persisted internally by the      |
+    | host's portal service.  To implement a true state     |
+    | track here, OpenRGB will need to manage a local       |
+    | boolean flag inside its own configuration files (e.g. |
+    | OpenRGB.json).                                        |
+    \*-----------------------------------------------------*/
+    return false;
+}
+
+std::string AutoStart::GetExePath()
+{
+    /*-----------------------------------------------------*\
+    | Flatpak applications always run from this specific    |
+    | exported path hierarchy                               |
+    \*-----------------------------------------------------*/
+    return "/app/bin/openrgb";
+}

AutoStart/AutoStart-Flatpak.h

@@ -0,0 +1,31 @@
+/*---------------------------------------------------------*\
+| AutoStart-Flatpak.h                                       |
+|                                                           |
+|   Autostart implementation for Linux via Flatpak Portal   |
+|                                                           |
+|   Adam Honse <[email protected]>      04 Sep 2026 |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#pragma once
+
+#include <string>
+#include "AutoStart.h"
+
+class AutoStart : public AutoStartInterface
+{
+public:
+    AutoStart(std::string name);
+
+    bool        DisableAutoStart();
+    bool        EnableAutoStart(AutoStartInfo autostart_info);
+    bool        IsAutoStartEnabled();
+    std::string GetExePath();
+
+private:
+    void        InitAutoStart(std::string name);
+    bool        CallBackgroundPortal(bool enable, const AutoStartInfo& autostart_info = {});
+    
+    std::string app_name;
+};

AutoStart/AutoStart.h

@@ -40,9 +40,15 @@ protected:
 #include "AutoStart-Windows.h"
 #endif
 
+#ifdef FLATPAK_BUILD
+#include "AutoStart-Flatpak.h"
+#endif
+
 #ifdef __linux__
+#ifndef FLATPAK_BUILD
 #include "AutoStart-Linux.h"
 #endif
+#endif
 
 #ifdef __APPLE__
 #include "AutoStart-MacOS.h"

Controllers/ASRockSMBusController/ASRockGPUSMBusController/ASRockGPUSMBusController.cpp

@@ -186,8 +186,8 @@ void ASRockGPUSMBusController::SetChannelColor(uint8_t channel_idx, uint8_t red,
         red,
         green,
         blue,
-        0x80,  // Brightness
-        0xFF,  // Effect speed
+        0x80,  // Effect speed
+        0xFF,  // Brightness
         0x00,  // Effect direction
         0x1A   // Unknown constant
     };

Controllers/ASRockSMBusController/ASRockGPUSMBusController/ASRockGPUSMBusControllerDetect.cpp

@@ -11,6 +11,7 @@
 #include "ASRockGPUSMBusController.h"
 #include "LogManager.h"
 #include "RGBController_ASRockGPUSMBus.h"
+#include "i2c_amd_gpu.h"
 #include "i2c_smbus.h"
 #include "pci_ids.h"
 
@@ -18,15 +19,12 @@ DetectedControllers DetectASRockGPUSMBusControllers(i2c_smbus_interface* bus, ui
 {
     DetectedControllers detected_controllers;
 
-    LOG_DEBUG("[ASRock GPU] Checking GPU I2C bus for RGB controller at 0x%02X", address);
-
-    if(bus->i2c_smbus_write_quick(address, I2C_SMBUS_WRITE) < 0)
+    if(bus->info.pci_vendor == AMD_GPU_VEN && !is_amd_gpu_i2c_bus(bus))
     {
-        LOG_DEBUG("[ASRock GPU] No response at address 0x%02X", address);
         return(detected_controllers);
     }
 
-    LOG_DEBUG("[ASRock GPU] Device responded at 0x%02X, creating controller", address);
+    LOG_DEBUG("[ASRock GPU] Checking GPU I2C bus for RGB controller at 0x%02X", address);
 
     ASRockGPUSMBusController* controller = new ASRockGPUSMBusController(bus, address, name);
 
@@ -44,3 +42,6 @@ DetectedControllers DetectASRockGPUSMBusControllers(i2c_smbus_interface* bus, ui
 }
 
 REGISTER_I2C_PCI_DETECTOR("ASRock Radeon RX 9070 XT Steel Legend",   DetectASRockGPUSMBusControllers, AMD_GPU_VEN, AMD_NAVI48_DEV, ASROCK_SUB_VEN, 0x5403, ASROCK_GPU_SMBUS_ADDRESS);
+REGISTER_I2C_PCI_DETECTOR("ASRock Radeon RX 9070 XT Steel Legend Dark", DetectASRockGPUSMBusControllers, AMD_GPU_VEN, AMD_NAVI48_DEV, ASROCK_SUB_VEN, 0x5414, ASROCK_GPU_SMBUS_ADDRESS);
+REGISTER_I2C_PCI_DETECTOR("ASRock Radeon RX 9070 XT Taichi 16GB OC", DetectASRockGPUSMBusControllers, AMD_GPU_VEN, AMD_NAVI48_DEV, ASROCK_SUB_VEN, 0x5401, ASROCK_GPU_SMBUS_ADDRESS);
+REGISTER_I2C_PCI_DETECTOR("ASRock Radeon RX 9060 XT Steel Legend",   DetectASRockGPUSMBusControllers, AMD_GPU_VEN, AMD_NAVI44_DEV, ASROCK_SUB_VEN, 0x5407, ASROCK_GPU_SMBUS_ADDRESS);

Controllers/ASRockSMBusController/ASRockGPUSMBusController/RGBController_ASRockGPUSMBus.cpp

@@ -11,6 +11,17 @@
 
 #include "RGBController_ASRockGPUSMBus.h"
 
+/**------------------------------------------------------------------*\
+    @name ASRock GPU SMBus
+    @category GPU
+    @type I2C
+    @save :x:
+    @direct :white_check_mark:
+    @effects :x:
+    @detectors DetectASRockGPUSMBusControllers
+    @comment
+\*-------------------------------------------------------------------*/
+
 RGBController_ASRockGPUSMBus::RGBController_ASRockGPUSMBus(ASRockGPUSMBusController* controller_ptr)
 {
     controller  = controller_ptr;
@@ -33,6 +44,8 @@ RGBController_ASRockGPUSMBus::RGBController_ASRockGPUSMBus(ASRockGPUSMBusControl
 
 RGBController_ASRockGPUSMBus::~RGBController_ASRockGPUSMBus()
 {
+    Shutdown();
+
     delete controller;
 }
 

Controllers/AlienwareController/AlienwareController.cpp

@@ -32,6 +32,7 @@ static const std::map<alienware_platform_id, uint8_t> zone_quirks_table =
     { 0x0C01,   4 },    // Dell G5 SE 5505
     { 0x0A01,  16 },    // Dell G7 15 7500
     { 0x0E03,   4 },    // Dell G15   5511
+    { 0x0E07,   4 },    // Dell G15   5520
     { 0x0E0A,   4 }     // Dell G15   5530
 
 };
@@ -49,9 +50,21 @@ static const std::map<alienware_platform_id, std::vector<const char*>> zone_name
                   "Light Bar 7",    "Light Bar 8",  "Light Bar 9",
                   "Light Bar 10",   "Light Bar 11", "Light Bar 12"              } },
     { 0x0E03,   { "Left",           "Middle",       "Right",        "Numpad"    } },
+    { 0x0E07,   { "Left",           "Middle",       "Right",        "Numpad"    } },
     { 0x0E0A,   { "Left",           "Middle",       "Right",        "Numpad"    } }
 };
 
+/*---------------------------------------------------------*\
+| Mapping the platform ID to the actual hardware zone IDs   |
+\*---------------------------------------------------------*/
+static const std::map<alienware_platform_id, std::vector<uint8_t>> zone_ids_table =
+{
+    { 0x0C01,   { 0x00, 0x01, 0x02, 0x03 } }, // Dell G5 SE 5505
+    { 0x0E03,   { 0x00, 0x01, 0x02, 0x03 } }, // Dell G15   5511
+    { 0x0E07,   { 0x10, 0x11, 0x12, 0x13 } }, // Dell G15   5520
+    { 0x0E0A,   { 0x10, 0x11, 0x12, 0x13 } }  // Dell G15   5530
+};
+
 static void SendHIDReport(hid_device *dev, const unsigned char* usb_buf, size_t usb_buf_size)
 {
     using namespace std::chrono_literals;
@@ -138,6 +151,21 @@ AlienwareController::AlienwareController(hid_device* dev_handle, const hid_devic
         }
     }
 
+    /*-----------------------------------------------------*\
+    | Initialize hardware zone IDs                          |
+    \*-----------------------------------------------------*/
+    if(zone_ids_table.count(platform_id))
+    {
+        zone_ids = zone_ids_table.at(platform_id);
+    }
+    else
+    {
+        for(size_t i = 0; i < number_of_zones; i++)
+        {
+            zone_ids.push_back(static_cast<uint8_t>(i));
+        }
+    }
+
     /*-----------------------------------------------------*\
     | Set defaults for all zones                            |
     | It doesn't seem possible to read the controller's     |
@@ -155,6 +183,7 @@ AlienwareController::AlienwareController(hid_device* dev_handle, const hid_devic
         zones[zone_idx].period      = 2000;
         zones[zone_idx].tempo       = ALIENWARE_TEMPO_MAX;
         zones[zone_idx].dim         = 0;
+        zones[zone_idx].direction   = 0;
     }
 
     /*-----------------------------------------------------*\
@@ -673,6 +702,15 @@ void AlienwareController::SetDim(uint8_t zone, uint8_t dim)
     }
 }
 
+void AlienwareController::SetDirection(uint8_t zone, uint8_t direction)
+{
+    if(zone < zones.size())
+    {
+        zones[zone].direction   = direction;
+        dirty                   = true;
+    }
+}
+
 void AlienwareController::UpdateDim()
 {
     if(!dirty_dim)
@@ -688,7 +726,8 @@ void AlienwareController::UpdateDim()
 
     for(size_t i = 0; i < zones.size(); i++)
     {
-        dim_zone_map[zones[i].dim].emplace_back((uint8_t)i);
+        uint8_t hw_zone = (i < zone_ids.size()) ? zone_ids[i] : static_cast<uint8_t>(i);
+        dim_zone_map[zones[i].dim].emplace_back(hw_zone);
     }
 
     for(std::pair<const uint8_t, std::vector<uint8_t>> &pair : dim_zone_map)
@@ -715,7 +754,8 @@ bool AlienwareController::UpdateDirect()
 
     for(size_t i = 0; i < zones.size(); i++)
     {
-        color_zone_map[zones[i].color[0]].emplace_back((uint8_t)i);
+        uint8_t hw_zone = (i < zone_ids.size()) ? zone_ids[i] : static_cast<uint8_t>(i);
+        color_zone_map[zones[i].color[0]].emplace_back(hw_zone);
     }
 
     for(std::pair<const RGBColor, std::vector<uint8_t>> &pair : color_zone_map)
@@ -759,8 +799,9 @@ void AlienwareController::UpdateMode()
     for(std::size_t zone_idx = 0; zone_idx < zones.size(); zone_idx++)
     {
         alienware_zone zone = zones[zone_idx];
+        uint8_t hw_zone = (zone_idx < zone_ids.size()) ? zone_ids[zone_idx] : static_cast<uint8_t>(zone_idx);
 
-        result = SelectZones({static_cast<uint8_t>(zone_idx)});
+        result = SelectZones({hw_zone});
 
         if(!result)
         {
@@ -783,18 +824,18 @@ void AlienwareController::UpdateMode()
 
             case ALIENWARE_MODE_MORPH:
                 {
-                    uint8_t  zones[2]   = { zone.mode,              zone.mode     };
+                    uint8_t  modes[2]   = { zone.mode,              zone.mode     };
                     uint16_t periods[2] = { zone.period,            zone.period   };
                     uint16_t tempos[2]  = { zone.tempo,             zone.tempo    };
                     RGBColor colors[2]  = { zone.color[0],          zone.color[1] };
 
-                    result = MultiModeAction(zones, periods, tempos, colors, 2);
+                    result = MultiModeAction(modes, periods, tempos, colors, 2);
                 }
                 break;
 
             case ALIENWARE_MODE_SPECTRUM:
                 {
-                    uint8_t  zones[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                    uint8_t  modes[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                             ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                             ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                             ALIENWARE_MODE_MORPH };
@@ -807,13 +848,13 @@ void AlienwareController::UpdateMode()
                                             zone.tempo,             zone.tempo,
                                             zone.tempo };
 
-                    result = MultiModeAction(zones, periods, tempos, rainbow_colors[0], 7);
+                    result = MultiModeAction(modes, periods, tempos, rainbow_colors[0], 7);
                 }
                 break;
 
             case ALIENWARE_MODE_RAINBOW:
                 {
-                    uint8_t  zones[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                    uint8_t  modes[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                             ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                             ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                             ALIENWARE_MODE_MORPH };
@@ -826,18 +867,19 @@ void AlienwareController::UpdateMode()
                                             zone.tempo,             zone.tempo,
                                             zone.tempo };
 
-                    result = MultiModeAction(zones, periods, tempos, rainbow_colors[zone_idx], 7);
+                    unsigned int color_idx = (zone.direction == MODE_DIRECTION_LEFT) ? (4 - 1 - (zone_idx % 4)) : (zone_idx % 4);
+                    result = MultiModeAction(modes, periods, tempos, rainbow_colors[color_idx], 7);
                 }
                 break;
 
             case ALIENWARE_MODE_BREATHING:
                 {
-                    uint8_t  zones[2]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH };
+                    uint8_t  modes[2]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH };
                     uint16_t periods[2] = { zone.period,            zone.period          };
                     uint16_t tempos[2]  = { zone.tempo,             zone.tempo           };
                     RGBColor colors[2]  = { zone.color[0],          0x0                  };
 
-                    result = MultiModeAction(zones, periods, tempos, colors, 2);
+                    result = MultiModeAction(modes, periods, tempos, colors, 2);
                 }
                 break;
 
@@ -864,6 +906,117 @@ void AlienwareController::UpdateMode()
     dirty = false;
 }
 
+void AlienwareController::SaveController()
+{
+    /*-----------------------------------------------------*\
+    | Save current mode configuration to EEPROM slot 0x0061 |
+    \*-----------------------------------------------------*/
+    UserAnimation(ALIENWARE_COMMAND_USER_ANIM_REMOVE, ALIENWARE_ANIM_DEFAULT, 0);
+    bool result = UserAnimation(ALIENWARE_COMMAND_USER_ANIM_NEW, ALIENWARE_ANIM_DEFAULT, 0);
+
+    if(!result)
+    {
+        return;
+    }
+
+    for(std::size_t zone_idx = 0; zone_idx < zones.size(); zone_idx++)
+    {
+        alienware_zone zone = zones[zone_idx];
+        uint8_t hw_zone = (zone_idx < zone_ids.size()) ? zone_ids[zone_idx] : static_cast<uint8_t>(zone_idx);
+
+        result = SelectZones({hw_zone});
+
+        if(!result)
+        {
+            return;
+        }
+
+        switch (zone.mode)
+        {
+            case ALIENWARE_MODE_COLOR:
+                result = ModeAction(zone.mode, 2000, ALIENWARE_TEMPO_MAX, zone.color[0]);
+                break;
+
+            case ALIENWARE_MODE_PULSE:
+                result = ModeAction(zone.mode, zone.period, zone.tempo, zone.color[0]);
+                break;
+
+            case ALIENWARE_MODE_MORPH:
+                {
+                    uint8_t  modes[2]   = { zone.mode,              zone.mode     };
+                    uint16_t periods[2] = { zone.period,            zone.period   };
+                    uint16_t tempos[2]  = { zone.tempo,             zone.tempo    };
+                    RGBColor colors[2]  = { zone.color[0],          zone.color[1] };
+
+                    result = MultiModeAction(modes, periods, tempos, colors, 2);
+                }
+                break;
+
+            case ALIENWARE_MODE_SPECTRUM:
+                {
+                    uint8_t  modes[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH };
+                    uint16_t periods[7] = { zone.period,            zone.period,
+                                            zone.period,            zone.period,
+                                            zone.period,            zone.period,
+                                            zone.period };
+                    uint16_t tempos[7] = {  zone.tempo,             zone.tempo,
+                                            zone.tempo,             zone.tempo,
+                                            zone.tempo,             zone.tempo,
+                                            zone.tempo };
+
+                    result = MultiModeAction(modes, periods, tempos, rainbow_colors[0], 7);
+                }
+                break;
+
+            case ALIENWARE_MODE_RAINBOW:
+                {
+                    uint8_t  modes[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH };
+                    uint16_t periods[7] = { zone.period,            zone.period,
+                                            zone.period,            zone.period,
+                                            zone.period,            zone.period,
+                                            zone.period };
+                    uint16_t tempos[7]  = { zone.tempo,             zone.tempo,
+                                            zone.tempo,             zone.tempo,
+                                            zone.tempo,             zone.tempo,
+                                            zone.tempo };
+
+                    unsigned int color_idx = (zone.direction == MODE_DIRECTION_LEFT) ? (4 - 1 - (zone_idx % 4)) : (zone_idx % 4);
+                    result = MultiModeAction(modes, periods, tempos, rainbow_colors[color_idx], 7);
+                }
+                break;
+
+            case ALIENWARE_MODE_BREATHING:
+                {
+                    uint8_t  modes[2]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH };
+                    uint16_t periods[2] = { zone.period,            zone.period          };
+                    uint16_t tempos[2]  = { zone.tempo,             zone.tempo           };
+                    RGBColor colors[2]  = { zone.color[0],          0x0                  };
+
+                    result = MultiModeAction(modes, periods, tempos, colors, 2);
+                }
+                break;
+
+            default:
+                result = false;
+        }
+
+        if(!result)
+        {
+            return;
+        }
+    }
+
+    UserAnimation(ALIENWARE_COMMAND_USER_ANIM_FINISH_SAVE, ALIENWARE_ANIM_DEFAULT, 0);
+    UserAnimation(ALIENWARE_COMMAND_USER_ANIM_DEFAULT, ALIENWARE_ANIM_DEFAULT, 0);
+    UserAnimation(ALIENWARE_COMMAND_USER_ANIM_STARTUP, ALIENWARE_ANIM_DEFAULT, 0);
+}
+
 void AlienwareController::UpdateController()
 {
     UpdateMode();

Controllers/AlienwareController/AlienwareController.h

@@ -123,11 +123,13 @@ public:
     void                        SetPeriod(uint8_t zone, uint16_t period);
     void                        SetTempo(uint8_t zone, uint16_t tempo);
     void                        SetDim(uint8_t zone, uint8_t dim);
+    void                        SetDirection(uint8_t zone, uint8_t direction);
     AlienwareReport             GetStatus(uint8_t subcommand);
 
     void                        UpdateDim();
     void                        UpdateMode();
     void                        UpdateController();
+    void                        SaveController();
 
 protected:
     hid_device* dev;
@@ -140,6 +142,7 @@ private:
         uint16_t                period;
         uint16_t                tempo;
         uint8_t                 dim;
+        uint8_t                 direction;
     } alienware_zone;
 
     typedef struct
@@ -153,6 +156,7 @@ private:
     std::string                 serial_number;
     std::string                 version;
     std::vector<const char*>    zone_names;
+    std::vector<uint8_t>        zone_ids;
     bool                        dirty;
     bool                        dirty_dim;
 

Controllers/AlienwareController/RGBController_Alienware.cpp

@@ -39,7 +39,7 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
     mode Color;
     Color.name                 = "Static";
     Color.value                = ALIENWARE_MODE_COLOR;
-    Color.flags                = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS;
+    Color.flags                = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_MANUAL_SAVE;
     Color.color_mode           = MODE_COLORS_PER_LED;
     Color.colors_min           = 1;
     Color.colors_max           = 1;
@@ -51,13 +51,13 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
     mode Pulse;
     Pulse.name                 = "Flashing";
     Pulse.value                = ALIENWARE_MODE_PULSE;
-    Pulse.flags                = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Pulse.flags                = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED | MODE_FLAG_MANUAL_SAVE;
     Pulse.color_mode           = MODE_COLORS_PER_LED;
     Pulse.colors_min           = 1;
     Pulse.colors_max           = 1;
-    Pulse.speed_min            = ALIENWARE_TEMPO_MIN;
-    Pulse.speed_max            = ALIENWARE_TEMPO_MAX;
-    Pulse.speed                = ALIENWARE_TEMPO_MIN;
+    Pulse.speed_min            = ALIENWARE_TEMPO_MAX;
+    Pulse.speed_max            = 50;
+    Pulse.speed                = 150;
     Pulse.brightness_min       = 100;
     Pulse.brightness_max       = 0;
     Pulse.brightness           = 0;
@@ -66,14 +66,16 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
     mode Morph;
     Morph.name                 = "Morph";
     Morph.value                = ALIENWARE_MODE_MORPH;
-    Morph.flags                = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Morph.flags                = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED | MODE_FLAG_MANUAL_SAVE;
     Morph.color_mode           = MODE_COLORS_MODE_SPECIFIC;
-    Morph.colors_min           = 2 * controller->GetZoneCount();
-    Morph.colors_max           = Morph.colors_min;
-    Morph.colors.resize(Morph.colors_max);
-    Morph.speed_min            = ALIENWARE_TEMPO_MIN;
-    Morph.speed_max            = ALIENWARE_TEMPO_MAX;
-    Morph.speed                = ALIENWARE_TEMPO_MIN;
+    Morph.colors_min           = 2;
+    Morph.colors_max           = 2 * controller->GetZoneCount();
+    Morph.colors.resize(2);
+    Morph.colors[0]            = 0x0000FF;
+    Morph.colors[1]            = 0xFF0000;
+    Morph.speed_min            = ALIENWARE_TEMPO_MAX;
+    Morph.speed_max            = 20;
+    Morph.speed                = 100;
     Morph.brightness_min       = 100;
     Morph.brightness_max       = 0;
     Morph.brightness           = 0;
@@ -82,11 +84,11 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
     mode Spectrum;
     Spectrum.name              = "Spectrum Cycle";
     Spectrum.value             = ALIENWARE_MODE_SPECTRUM;
-    Spectrum.flags             = MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Spectrum.flags             = MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED | MODE_FLAG_MANUAL_SAVE;
     Spectrum.color_mode        = MODE_COLORS_NONE;
-    Spectrum.speed_min         = ALIENWARE_TEMPO_SPECTRUM;
-    Spectrum.speed_max         = ALIENWARE_TEMPO_MAX;
-    Spectrum.speed             = ALIENWARE_TEMPO_SPECTRUM;
+    Spectrum.speed_min         = ALIENWARE_TEMPO_MAX;
+    Spectrum.speed_max         = ALIENWARE_TEMPO_SPECTRUM;
+    Spectrum.speed             = 40;
     Spectrum.brightness_min    = 100;
     Spectrum.brightness_max    = 0;
     Spectrum.brightness        = 0;
@@ -95,11 +97,12 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
     mode Rainbow;
     Rainbow.name               = "Rainbow Wave";
     Rainbow.value              = ALIENWARE_MODE_RAINBOW;
-    Rainbow.flags              = MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Rainbow.flags              = MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED | MODE_FLAG_HAS_DIRECTION_LR | MODE_FLAG_MANUAL_SAVE;
     Rainbow.color_mode         = MODE_COLORS_NONE;
-    Rainbow.speed_min          = ALIENWARE_TEMPO_SPECTRUM;
-    Rainbow.speed_max          = ALIENWARE_TEMPO_MAX;
-    Rainbow.speed              = ALIENWARE_TEMPO_SPECTRUM;
+    Rainbow.speed_min          = ALIENWARE_TEMPO_MAX;
+    Rainbow.speed_max          = ALIENWARE_TEMPO_SPECTRUM;
+    Rainbow.speed              = 40;
+    Rainbow.direction          = MODE_DIRECTION_RIGHT;
     Rainbow.brightness_min     = 100;
     Rainbow.brightness_max     = 0;
     Rainbow.brightness         = 0;
@@ -108,13 +111,13 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
     mode Breathing;
     Breathing.name             = "Breathing";
     Breathing.value            = ALIENWARE_MODE_BREATHING;
-    Breathing.flags            = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Breathing.flags            = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED | MODE_FLAG_MANUAL_SAVE;
     Breathing.color_mode       = MODE_COLORS_PER_LED;
     Breathing.colors_min       = 1;
     Breathing.colors_max       = 1;
-    Breathing.speed_min        = ALIENWARE_TEMPO_MIN;
-    Breathing.speed_max        = ALIENWARE_TEMPO_MAX;
-    Breathing.speed            = ALIENWARE_TEMPO_MIN;
+    Breathing.speed_min        = ALIENWARE_TEMPO_MAX;
+    Breathing.speed_max        = 50;
+    Breathing.speed            = 150;
     Breathing.brightness_min   = 100;
     Breathing.brightness_max   = 0;
     Breathing.brightness       = 0;
@@ -224,6 +227,7 @@ void RGBController_Alienware::DeviceUpdateMode()
             uint16_t period = 0x07d0;
 
             controller->SetMode(zone_idx, current_mode.value);
+            controller->SetDirection(zone_idx, current_mode.direction);
 
             switch(current_mode_idx)
             {
@@ -235,6 +239,7 @@ void RGBController_Alienware::DeviceUpdateMode()
                     break;
 
                 case ALIENWARE_MODE_PULSE:
+                    period = std::max<uint16_t>(500, (uint16_t)(current_mode.speed * 10));
                     controller->SetPeriod(zone_idx, period);
                     controller->SetColor( zone_idx, colors[current_zone.start_idx]);
                     controller->SetTempo( zone_idx, current_mode.speed);
@@ -242,10 +247,22 @@ void RGBController_Alienware::DeviceUpdateMode()
                     break;
 
                 case ALIENWARE_MODE_MORPH:
+                    {
+                        RGBColor c1 = (current_mode.colors.size() >= 1) ? current_mode.colors[0] : 0x0000FF;
+                        RGBColor c2 = (current_mode.colors.size() >= 2) ? current_mode.colors[1] : 0xFF0000;
+
+                        if(current_mode.colors.size() >= (std::size_t)((zone_idx + 1) * 2))
+                        {
+                            c1 = current_mode.colors[zone_idx * 2];
+                            c2 = current_mode.colors[(zone_idx * 2) + 1];
+                        }
+
+                        period = std::max<uint16_t>(400, (uint16_t)(current_mode.speed * 10));
                         controller->SetPeriod(zone_idx, period);
-                    controller->SetColor( zone_idx, current_mode.colors[zone_idx * 2], current_mode.colors[(zone_idx * 2) + 1]);
+                        controller->SetColor( zone_idx, c1, c2);
                         controller->SetTempo( zone_idx, current_mode.speed);
                         controller->SetDim(   zone_idx, modes[current_mode_idx].brightness);
+                    }
                     break;
 
                 case ALIENWARE_MODE_SPECTRUM:
@@ -256,6 +273,7 @@ void RGBController_Alienware::DeviceUpdateMode()
                     break;
 
                 case ALIENWARE_MODE_BREATHING:
+                    period = std::max<uint16_t>(500, (uint16_t)(current_mode.speed * 10));
                     controller->SetPeriod(zone_idx, period);
                     controller->SetColor( zone_idx, colors[current_zone.start_idx], 0x0);
                     controller->SetTempo( zone_idx, current_mode.speed);
@@ -282,3 +300,9 @@ void RGBController_Alienware::DeviceUpdateMode()
         current_mode              = new_current_mode;
     }
 }
+
+void RGBController_Alienware::DeviceSaveMode()
+{
+    controller->SaveController();
+}
+

Controllers/AlienwareController/RGBController_Alienware.h

@@ -28,6 +28,7 @@ public:
     void        DeviceUpdateSingleLED(int led);
 
     void        DeviceUpdateMode();
+    void        DeviceSaveMode();
 
 private:
     AlienwareController*                    controller;

Controllers/AlienwareMonitorController/AlienwareAW3423DWFController/AlienwareAW3423DWFController.cpp

@@ -40,11 +40,11 @@ std::vector<unsigned char> AlienwareAW3423DWFController::GetReportResponse()
 
 void AlienwareAW3423DWFController::PerformLogin()
 {
-    unsigned char init_packet[64] =
-    {
-        0x40, 0xE1, 0x01
-    };
-    SendControlPacket(init_packet, 4);
+    unsigned char init_packet[192] = {0x00};
+    init_packet[0] = 0x40;
+    init_packet[1] = 0xE1;
+    init_packet[2] = 0x01;
+    SendControlPacket(init_packet, 192);
 
     std::vector<unsigned char> response = GetReportResponse();
 

Controllers/AsusAuraUSBController/AsusAuraUSBControllerDetect.cpp

@@ -417,7 +417,7 @@ REGISTER_HID_DETECTOR   ("ASUS Aura Addressable",                       DetectAs
 REGISTER_HID_DETECTOR   ("ASUS Aura Addressable",                       DetectAsusAuraUSBAddressable,   AURA_USB_VID, AURA_ADDRESSABLE_4_PID);
 REGISTER_HID_DETECTOR   ("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_1_PID);
 REGISTER_HID_DETECTOR   ("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_2_PID);
-REGISTER_HID_DETECTOR   ("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_3_PID);
+REGISTER_HID_DETECTOR_PU("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_3_PID,                           0xFF72, 0x00A1);
 REGISTER_HID_DETECTOR   ("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_4_PID);
 REGISTER_HID_DETECTOR   ("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_5_PID);
 

Controllers/AsusMonitorController/AsusMonitorControllerDetect.cpp

@@ -22,9 +22,12 @@
 | Product ID                                                |
 \*---------------------------------------------------------*/
 #define ASUS_ROG_STRIX_XG27AQDMG_PID                   0x1BA3
+#define ASUS_ROG_STRIX_XG27ACDNG_PID                   0x1BC9
 #define ASUS_ROG_STRIX_XG27UCG_PID                     0x1BB4
 #define ASUS_ROG_SWIFT_PG32UCDM_PID                    0x1B2B
 #define ASUS_ROG_SWIFT_PG32UCDMR_PID                   0x1C9B
+#define ASUS_ROG_SWIFT_PG32UCDP_PID                    0x1BCA
+#define ASUS_ROG_AURA_MONITOR_LIGHT_BAR_PID            0x1AC8
 
 DetectedControllers DetectAsusMonitorControllers(hid_device_info* info, const std::string& name)
 {
@@ -45,7 +48,13 @@ DetectedControllers DetectAsusMonitorControllers(hid_device_info* info, const st
 }
 
 REGISTER_HID_DETECTOR_IPU("Asus ROG STRIX XG27AQDMG",   DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_STRIX_XG27AQDMG_PID,   1, 0xFF72, 0x00A1);
+REGISTER_HID_DETECTOR_IPU("Asus ROG STRIX XG27ACDNG",   DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_STRIX_XG27ACDNG_PID,   1, 0xFF72, 0x00A1);
 REGISTER_HID_DETECTOR_IPU("Asus ROG STRIX XG27UCG",     DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_STRIX_XG27UCG_PID,     1, 0xFF72, 0x00A1);
 REGISTER_HID_DETECTOR_IPU("Asus ROG SWIFT PG32UCDM",    DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_SWIFT_PG32UCDM_PID,    1, 0xFF72, 0x00A1);
 REGISTER_HID_DETECTOR_IPU("Asus ROG SWIFT PG32UCDMR",   DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_SWIFT_PG32UCDMR_PID,   1, 0xFF72, 0x00A1);
+REGISTER_HID_DETECTOR_IPU("Asus ROG SWIFT PG32UCDP",    DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_SWIFT_PG32UCDP_PID,    1, 0xFF72, 0x00A1);
+/*---------------------------------------------------------*\
+| ALB01 exposes the Aura HID collection on interface 2.     |
+\*---------------------------------------------------------*/
+REGISTER_HID_DETECTOR_IPU("Asus ROG Aura Monitor Light Bar", DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_AURA_MONITOR_LIGHT_BAR_PID, 2, 0xFF72, 0x00A1);
 

Controllers/ClevoKeyboardController/ClevoKeyboardController.cpp

@@ -335,7 +335,7 @@ void ClevoKeyboardController::SetEffect829x(unsigned char mode_value, const std:
     {
         for(size_t i = 0; i < colors.size() && i < 2; i++)
         {
-            SendColorSlot829x(CLEVO_829X_CMD_SCAN_COLOR, CLEVO_829X_COLOR_SLOT_BASE + i, colors[i]);
+            SendColorSlot829x(CLEVO_829X_CMD_SCAN_COLOR, CLEVO_829X_COLOR_SLOT_BASE + (unsigned char)i, colors[i]);
         }
     }
 

Controllers/ClevoKeyboardController/ClevoKeyboardDevices.cpp

@@ -18,71 +18,79 @@
 |                                                           |
 | Based on KEYBOARD_SIZE_TKL with numpad added and          |
 | navigation cluster adjusted to match Clevo's layout.      |
-|                                                           |
-| Hardware LED indices (value field):                       |
-| - Row 5 (F-keys):     105-124                             |
-| - Row 4 (numbers):    84-102                              |
-| - Row 3 (QWERTY):     63-81                               |
-| - Row 2 (home):       42-59                               |
-| - Row 1 (Z row):      22-39                               |
-| - Row 0 (modifiers):  0-18                                |
 \*---------------------------------------------------------*/
 
 /*---------------------------------------------------------*\
-| LED values in TKL order (fn_row + main + extras)          |
+| LED values, in physical (row, then column) order.         |
+|                                                           |
+| This must match the order KeyboardLayoutManager assigns   |
+| default_values against: the structural keymap sorted by   |
+| (row, col) across main+fn_row+extras combined, NOT the    |
+| fn_row-then-main-then-extras order the zone tables below  |
+| are declared in. Getting this wrong silently misassigns   |
+| almost every key from Print Screen onward, not just a few.|
 |                                                           |
-| Values follow the key order in KeyboardLayoutManager.cpp. |
 | For ANSI-only keys (not present on this ISO keyboard),    |
 | use 0 as a placeholder - they won't be displayed.         |
 | Numpad values are added via edit_keys.                    |
 \*---------------------------------------------------------*/
 static const std::vector<unsigned int> clevo_tkl_values =
 {
-    /*---------------------------------------------------------*\
-    | Function row (keyboard_zone_fn_row)                       |
-    \*---------------------------------------------------------*/
+    /*-----------------------------------------------------*\
+    | Row 0: fn_row + Print Screen/Scroll Lock/Pause        |
+    \*-----------------------------------------------------*/
     105,                                                        // Escape
     106, 107, 108, 109,                                         // F1-F4
     110, 111, 112, 113,                                         // F5-F8
     114, 115, 116, 117,                                         // F9-F12
+    118,                                                        // Print Screen
+    0,                                                          // Scroll Lock (removed via edit_keys)
+    0,                                                          // Pause (removed via edit_keys)
 
-    /*---------------------------------------------------------*\
-    | Main block - Row 1 (keyboard_zone_main)                   |
-    \*---------------------------------------------------------*/
+    /*-----------------------------------------------------*\
+    | Row 1: numbers row + Insert/Home/Page Up              |
+    \*-----------------------------------------------------*/
     84,                                                         // Back tick
     85, 86, 87, 88, 89, 90, 91, 92, 93, 94,                     // 1-0
     95, 96,                                                     // Minus, Equals
     98,                                                         // Backspace
+    119,                                                        // Insert
+    121,                                                        // Home
+    122,                                                        // Page Up
 
-    /*---------------------------------------------------------*\
-    | Main block - Row 2                                        |
-    \*---------------------------------------------------------*/
+    /*-----------------------------------------------------*\
+    | Row 2: Tab/QWERTY row + Delete/End/PageDown           |
+    \*-----------------------------------------------------*/
     63,                                                         // Tab
     65, 66, 67, 68, 69, 70, 71, 72, 73, 74,                     // Q-P
     75, 76,                                                     // [ ]
     0,                                                          // ANSI backslash (not on ISO)
+    120,                                                        // Delete
+    124,                                                        // End
+    123,                                                        // Page Down
 
-    /*---------------------------------------------------------*\
-    | Main block - Row 3                                        |
-    \*---------------------------------------------------------*/
+    /*-----------------------------------------------------*\
+    | Row 3: Caps Lock/home row/Enter                       |
+    \*-----------------------------------------------------*/
     42,                                                         // Caps Lock
     44, 45, 46, 47, 48, 49, 50, 51, 52,                         // A-L
     53, 54,                                                     // ; '
     55,                                                         // ISO # (POUND)
-    77,                                                         // Enter (ANSI/ISO share same LED)
+    56,                                                         // Enter
 
-    /*---------------------------------------------------------*\
-    | Main block - Row 4                                        |
-    \*---------------------------------------------------------*/
-    22,                                                         // Left Shift
-    23,                                                         // ISO backslash
+    /*-----------------------------------------------------*\
+    | Row 4: Left Shift/ISO backslash/Z row + Up            |
+    \*-----------------------------------------------------*/
+    21,                                                         // Left Shift
+    77,                                                         // ISO backslash
     24, 25, 26, 27, 28, 29, 30, 31, 32,                         // Z-. (9 keys)
     33,                                                         // /
     35,                                                         // Right Shift
+    14,                                                         // Up
 
-    /*---------------------------------------------------------*\
-    | Main block - Row 5                                        |
-    \*---------------------------------------------------------*/
+    /*-----------------------------------------------------*\
+    | Row 5: bottom modifier row + Left/Down/Right          |
+    \*-----------------------------------------------------*/
     0,                                                          // Left Ctrl
     3,                                                          // Left Win
     4,                                                          // Left Alt
@@ -91,24 +99,6 @@ static const std::vector<unsigned int> clevo_tkl_values =
     0,                                                          // Right Fn (removed via edit_keys)
     0,                                                          // Menu (removed via edit_keys)
     12,                                                         // Right Ctrl
-
-    /*---------------------------------------------------------*\
-    | Extras - Navigation cluster (keyboard_zone_extras)        |
-    \*---------------------------------------------------------*/
-    118,                                                        // Print Screen
-    0,                                                          // Scroll Lock (removed via edit_keys)
-    0,                                                          // Pause (removed via edit_keys)
-    119,                                                        // Insert
-    121,                                                        // Home
-    123,                                                        // Page Up
-    120,                                                        // Delete
-    122,                                                        // End
-    124,                                                        // Page Down
-
-    /*---------------------------------------------------------*\
-    | Extras - Arrow keys                                       |
-    \*---------------------------------------------------------*/
-    14,                                                         // Up
     13,                                                         // Left
     18,                                                         // Down
     15,                                                         // Right

Controllers/CoolerMasterController/CMSmallARGBController/CMSmallARGBController.cpp

@@ -13,11 +13,6 @@
 #include "CMSmallARGBController.h"
 #include "StringUtils.h"
 
-cm_small_argb_headers cm_small_argb_header_data[1] =
-{
-    { "CM Small ARGB",  0x01, true,  12 }
-};
-
 CMSmallARGBController::CMSmallARGBController(hid_device* dev_handle, char *_path)
 {
     dev                     = dev_handle;
@@ -92,6 +87,24 @@ std::string CMSmallARGBController::GetSerial()
     return(StringUtils::wstring_to_string(serial_string));
 }
 
+std::string CMSmallARGBController::GetVersion()
+{
+    /*-----------------------------------------------------*\
+    | This device uses the serial value to determine the    |
+    | version.  It does not report a proper unique serial.  |
+    \*-----------------------------------------------------*/
+    std::string serial_string = GetSerial();
+
+    if(serial_string == CM_SMALL_ARGB_FW0012)
+    {
+        return("0012");
+    }
+    else
+    {
+        return("Unsupported");
+    }
+}
+
 std::string CMSmallARGBController::GetLocation()
 {
     return("HID: " + location);
@@ -122,6 +135,11 @@ unsigned char CMSmallARGBController::GetLedSpeed()
     return(current_speed);
 }
 
+unsigned char CMSmallARGBController::GetBrightness()
+{
+    return(current_brightness);
+}
+
 bool CMSmallARGBController::GetRandomColours()
 {
     return(bool_random);
@@ -217,9 +235,9 @@ void CMSmallARGBController::SendUpdate()
 
     hid_write(dev, buffer, buffer_size);
 
-    buffer[CM_SMALL_ARGB_COMMAND_BYTE]                  = 0x0b;
-    buffer[CM_SMALL_ARGB_FUNCTION_BYTE]                 = (false) ? 0x01 : 0x02; //This controls custom mode TODO
-    buffer[CM_SMALL_ARGB_ZONE_BYTE]                     = cm_small_argb_header_data[0].header;
+    buffer[CM_SMALL_ARGB_COMMAND_BYTE]                  = 0x0B;
+    buffer[CM_SMALL_ARGB_FUNCTION_BYTE]                 = 0x02;
+    buffer[CM_SMALL_ARGB_ZONE_BYTE]                     = 0x01;
     buffer[CM_SMALL_ARGB_MODE_BYTE]                     = current_mode;
     buffer[CM_SMALL_ARGB_SPEED_BYTE]                    = current_speed;
     buffer[CM_SMALL_ARGB_COLOUR_INDEX_BYTE]             = (bool_random) ? 0x00 : 0x10; //This looks to still be the colour index and controls random colours

Controllers/CoolerMasterController/CMSmallARGBController/CMSmallARGBController.h

@@ -39,16 +39,6 @@ enum
     CM_SMALL_ARGB_BLUE_BYTE             = 11,
 };
 
-struct cm_small_argb_headers
-{
-    const char*     name;
-    unsigned char   header;
-    bool            digital;
-    unsigned int    count;
-};
-
-extern cm_small_argb_headers cm_small_argb_header_data[1];
-
 enum
 {
     CM_SMALL_ARGB_MODE_SPECTRUM       = 0x01,   //Spectrum Mode
@@ -71,6 +61,8 @@ enum
     CM_SMALL_ARGB_SPEED_FASTEST       = 0x04,   // Fastest speed
 };
 
+#define CM_SMALL_ARGB_FW0012            std::string("A202104052336")
+
 class CMSmallARGBController
 {
 public:
@@ -80,12 +72,14 @@ public:
     std::string         GetDeviceName();
     std::string         GetSerial();
     std::string         GetLocation();
+    std::string         GetVersion();
 
     unsigned char       GetMode();
     unsigned char       GetLedRed();
     unsigned char       GetLedGreen();
     unsigned char       GetLedBlue();
     unsigned char       GetLedSpeed();
+    unsigned char       GetBrightness();
     bool                GetRandomColours();
 
     void                SetLedCount(int zone, int led_count);

Controllers/CoolerMasterController/CMSmallARGBController/RGBController_CMSmallARGBController.cpp

@@ -27,22 +27,68 @@
 RGBController_CMSmallARGBController::RGBController_CMSmallARGBController(CMSmallARGBController* controller_ptr)
 {
     controller                  = controller_ptr;
-    unsigned char speed         = controller->GetLedSpeed();
 
-    name                        = cm_small_argb_header_data[0].name;
+    name                        = controller->GetDeviceName();
     vendor                      = "Cooler Master";
     type                        = DEVICE_TYPE_LEDSTRIP;
-    description                 = controller->GetDeviceName();
-    version                     = "2.0 for FW0012";
+    description                 = "Cooler Master Small ARGB Controller Device";
+    version                     = controller->GetVersion();
     serial                      = controller->GetSerial();
     location                    = controller->GetLocation();
 
-    if(serial >= CM_SMALL_ARGB_FW0012)
+    SetupModes();
+    SetupZones();
+
+    /*-----------------------------------------------------*\
+    | Initialize the active mode to the device's current    |
+    | mode                                                  |
+    \*-----------------------------------------------------*/
+    int             device_mode         = controller->GetMode();
+
+    for(std::size_t mode_idx = 0; mode_idx < modes.size(); mode_idx++)
+    {
+        if(modes[mode_idx].value == device_mode)
+        {
+            active_mode = (int)mode_idx;
+
+            if((modes[mode_idx].flags & MODE_FLAG_HAS_MODE_SPECIFIC_COLOR) && (modes[mode_idx].colors.size() > 0))
+            {
+                modes[mode_idx].colors[0] = ToRGBColor(controller->GetLedRed(), controller->GetLedGreen(), controller->GetLedBlue());
+            }
+
+            if(modes[mode_idx].flags & MODE_FLAG_HAS_SPEED)
+            {
+                modes[mode_idx].speed = controller->GetLedSpeed();
+            }
+
+            if(modes[mode_idx].flags & MODE_FLAG_HAS_BRIGHTNESS)
+            {
+                modes[mode_idx].brightness = controller->GetBrightness();
+            }
+
+            if(modes[mode_idx].flags & MODE_FLAG_HAS_RANDOM_COLOR)
+            {
+                modes[mode_idx].color_mode = controller->GetRandomColours() ? MODE_COLORS_RANDOM : MODE_COLORS_MODE_SPECIFIC;
+            }
+
+            break;
+        }
+    }
+}
+
+void RGBController_CMSmallARGBController::SetupModes()
+{
+    /*-----------------------------------------------------*\
+    | The Small ARGB only supports Direct mode from FW0012  |
+    | onwards, older firmware does not accept direct mode   |
+    | packets                                               |
+    \*-----------------------------------------------------*/
+    //if(serial >= CM_SMALL_ARGB_FW0012)
     {
         mode Direct;
         Direct.name             = "Direct";
         Direct.value            = CM_SMALL_ARGB_MODE_DIRECT;
-        Direct.flags            = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS;
+        Direct.flags            = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_REQUIRES_ENTIRE_DEVICE;
         Direct.brightness_min   = 0;
         Direct.brightness_max   = CM_SMALL_ARGB_BRIGHTNESS_MAX;
         Direct.brightness       = CM_SMALL_ARGB_BRIGHTNESS_MAX;
@@ -69,7 +115,7 @@ RGBController_CMSmallARGBController::RGBController_CMSmallARGBController(CMSmall
     Reload.speed_min            = CM_SMALL_ARGB_SPEED_SLOWEST;
     Reload.speed_max            = CM_SMALL_ARGB_SPEED_FASTEST;
     Reload.color_mode           = MODE_COLORS_RANDOM;
-    Reload.speed                = speed;
+    Reload.speed                = CM_SMALL_ARGB_SPEED_NORMAL;
     modes.push_back(Reload);
 
     mode Recoil;
@@ -85,7 +131,7 @@ RGBController_CMSmallARGBController::RGBController_CMSmallARGBController(CMSmall
     Recoil.speed_min            = CM_SMALL_ARGB_SPEED_SLOWEST;
     Recoil.speed_max            = CM_SMALL_ARGB_SPEED_FASTEST;
     Recoil.color_mode           = MODE_COLORS_RANDOM;
-    Recoil.speed                = speed;
+    Recoil.speed                = CM_SMALL_ARGB_SPEED_NORMAL;
     modes.push_back(Recoil);
 
     mode Breathing;
@@ -101,7 +147,7 @@ RGBController_CMSmallARGBController::RGBController_CMSmallARGBController(CMSmall
     Breathing.speed_min         = CM_SMALL_ARGB_SPEED_SLOWEST;
     Breathing.speed_max         = CM_SMALL_ARGB_SPEED_FASTEST;
     Breathing.color_mode        = MODE_COLORS_RANDOM;
-    Breathing.speed             = speed;
+    Breathing.speed             = CM_SMALL_ARGB_SPEED_NORMAL;
     modes.push_back(Breathing);
 
     mode Refill;
@@ -117,7 +163,7 @@ RGBController_CMSmallARGBController::RGBController_CMSmallARGBController(CMSmall
     Refill.speed_min            = CM_SMALL_ARGB_SPEED_SLOWEST;
     Refill.speed_max            = CM_SMALL_ARGB_SPEED_FASTEST;
     Refill.color_mode           = MODE_COLORS_RANDOM;
-    Refill.speed                = speed;
+    Refill.speed                = CM_SMALL_ARGB_SPEED_NORMAL;
     modes.push_back(Refill);
 
     mode Demo;
@@ -130,7 +176,7 @@ RGBController_CMSmallARGBController::RGBController_CMSmallARGBController(CMSmall
     Demo.speed_min              = CM_SMALL_ARGB_SPEED_SLOWEST;
     Demo.speed_max              = CM_SMALL_ARGB_SPEED_FASTEST;
     Demo.color_mode             = MODE_COLORS_NONE;
-    Demo.speed                  = speed;
+    Demo.speed                  = CM_SMALL_ARGB_SPEED_NORMAL;
     modes.push_back(Demo);
 
     mode Spectrum;
@@ -143,39 +189,19 @@ RGBController_CMSmallARGBController::RGBController_CMSmallARGBController(CMSmall
     Spectrum.speed_min          = CM_SMALL_ARGB_SPEED_SLOWEST;
     Spectrum.speed_max          = CM_SMALL_ARGB_SPEED_FASTEST;
     Spectrum.color_mode         = MODE_COLORS_NONE;
-    Spectrum.speed              = speed;
+    Spectrum.speed              = CM_SMALL_ARGB_SPEED_NORMAL;
     modes.push_back(Spectrum);
 
+    /*-----------------------------------------------------*\
+    | Define Passthrough mode as requiring the entire       |
+    | device, it hands control over to the motherboard      |
+    \*-----------------------------------------------------*/
     mode PassThru;
     PassThru.name               = "Pass Thru";
     PassThru.value              = CM_SMALL_ARGB_MODE_PASSTHRU;
+    PassThru.flags              = MODE_FLAG_REQUIRES_ENTIRE_DEVICE;
     PassThru.color_mode         = MODE_COLORS_NONE;
     modes.push_back(PassThru);
-
-    SetupZones();
-
-    int temp_mode               = controller->GetMode();
-
-    for(int mode_idx = 0; mode_idx < (int)modes.size() ; mode_idx++)
-    {
-        if(temp_mode == modes[mode_idx].value)
-        {
-            active_mode         = mode_idx;
-            break;
-        }
-    }
-
-    if (modes[active_mode].flags & MODE_FLAG_HAS_MODE_SPECIFIC_COLOR)
-    {
-        modes[active_mode].colors[0] = ToRGBColor(controller->GetLedRed(), controller->GetLedGreen(), controller->GetLedBlue());
-    }
-
-    modes[active_mode].color_mode = (controller->GetRandomColours()) ? MODE_COLORS_RANDOM : MODE_COLORS_MODE_SPECIFIC;
-
-    if (modes[active_mode].flags & MODE_FLAG_HAS_SPEED)
-    {
-        modes[active_mode].speed = controller->GetLedSpeed();
-    }
 }
 
 RGBController_CMSmallARGBController::~RGBController_CMSmallARGBController()
@@ -248,7 +274,9 @@ void RGBController_CMSmallARGBController::SetupZones()
         {
             led new_led;
             new_led.name                            = zones[zone_idx].name;
-            new_led.name.append(", LED " + std::to_string(lp_idx));
+            new_led.name.append(", LED ");
+            new_led.name.append(std::to_string(lp_idx + 1));
+            new_led.value                           = (unsigned int)zone_idx;
 
             leds.push_back(new_led);
         }
@@ -261,7 +289,7 @@ void RGBController_CMSmallARGBController::DeviceConfigureZone(int zone_idx)
 {
     if((size_t)zone_idx < zones.size())
     {
-        controller->SetLedCount(cm_small_argb_header_data[zone_idx].header, zones[zone_idx].leds_count);
+        controller->SetLedCount(1, zones[zone_idx].leds_count);
 
         SetupZones();
     }
@@ -277,37 +305,79 @@ void RGBController_CMSmallARGBController::DeviceUpdateLEDs()
 
 void RGBController_CMSmallARGBController::DeviceUpdateZoneLEDs(int zone)
 {
-    if(serial >= CM_SMALL_ARGB_FW0012)
+    /*-----------------------------------------------------*\
+    | Only send direct packets while Direct mode is active. |
+    | Direct mode is only offered on FW0012 and newer, so   |
+    | older firmware will never send direct packets here    |
+    \*-----------------------------------------------------*/
+    if(modes[active_mode].value != CM_SMALL_ARGB_MODE_DIRECT)
     {
-        controller->SetLedsDirect( zones[zone].colors, zones[zone].leds_count );
+        return;
     }
+
+    controller->SetLedsDirect(zones[zone].colors, zones[zone].leds_count);
 }
 
 void RGBController_CMSmallARGBController::DeviceUpdateSingleLED(int led)
 {
-    DeviceUpdateZoneLEDs(led);
+    /*-----------------------------------------------------*\
+    | Map the LED back to its zone and update that zone     |
+    \*-----------------------------------------------------*/
+    unsigned int zone_idx = leds[led].value;
+
+    UpdateZoneLEDs(zone_idx);
 }
 
 void RGBController_CMSmallARGBController::SetCustomMode()
 {
-    /*-------------------------------------------------*\
-    | The small ARGB may not support "Direct" mode      |
-    |   in which case this will select "Pass Thru"      |
-    \*-------------------------------------------------*/
+    /*-----------------------------------------------------*\
+    | Direct mode is only supported on FW0012 and newer     |
+    \*-----------------------------------------------------*/
     if(serial >= CM_SMALL_ARGB_FW0012)
     {
-        active_mode = 0;
+        /*-------------------------------------------------*\
+        | Search the mode list for Direct mode              |
+        \*-------------------------------------------------*/
+        for(std::size_t mode_idx = 0; mode_idx < modes.size(); mode_idx++)
+        {
+            if(modes[mode_idx].name == "Direct")
+            {
+                SetActiveMode((int)mode_idx);
+                break;
+            }
+        }
     }
     else
     {
-        active_mode = 7;
+        /*-------------------------------------------------*\
+        | Direct mode is unsupported by the firmware,       |
+        | fall back to Pass Thru                            |
+        \*-------------------------------------------------*/
+        for(std::size_t mode_idx = 0; mode_idx < modes.size(); mode_idx++)
+        {
+            if(modes[mode_idx].value == CM_SMALL_ARGB_MODE_PASSTHRU)
+            {
+                SetActiveMode((int)mode_idx);
+                break;
+            }
+        }
     }
 }
 
 void RGBController_CMSmallARGBController::DeviceUpdateMode()
 {
+    /*-----------------------------------------------------*\
+    | Set up mode parameters                                |
+    \*-----------------------------------------------------*/
     bool            random_colours  = (modes[active_mode].color_mode == MODE_COLORS_RANDOM);
-    RGBColor colour         = (modes[active_mode].color_mode == MODE_COLORS_MODE_SPECIFIC) ? modes[active_mode].colors[0] : 0;
+    RGBColor        colour          = 0;
+    unsigned int    speed           = modes[active_mode].speed;
+    unsigned int    brightness      = modes[active_mode].brightness;
 
-    controller->SetMode( modes[active_mode].value, modes[active_mode].speed, modes[active_mode].brightness, colour, random_colours);
+    if(modes[active_mode].colors.size() > 0)
+    {
+        colour                      = modes[active_mode].colors[0];
+    }
+
+    controller->SetMode(modes[active_mode].value, speed, brightness, colour, random_colours);
 }

Controllers/CoolerMasterController/CMSmallARGBController/RGBController_CMSmallARGBController.h

@@ -18,7 +18,6 @@
 #define CM_SMALL_ARGB_MIN_LEDS          4
 #define CM_SMALL_ARGB_MAX_LEDS          48
 #define CM_SMALL_ARGB_BRIGHTNESS_MAX    0xFF
-#define CM_SMALL_ARGB_FW0012            "A202104052336"
 
 class RGBController_CMSmallARGBController : public RGBController
 {
@@ -26,7 +25,9 @@ public:
     RGBController_CMSmallARGBController(CMSmallARGBController* controller_ptr);
     ~RGBController_CMSmallARGBController();
 
+    void        SetupModes();
     void        SetupZones();
+
     void        DeviceConfigureZone(int zone_idx);
 
     void        DeviceUpdateLEDs();
@@ -35,9 +36,7 @@ public:
 
     void        SetCustomMode();
     void        DeviceUpdateMode();
-private:
-    void        Init_Controller();
-    int         GetDeviceMode();
 
+private:
     CMSmallARGBController*  controller;
 };

Controllers/CoolerMasterController/CoolerMasterControllerDetect.cpp

@@ -327,10 +327,19 @@ DetectedControllers DetectCoolerMasterSmallARGB(hid_device_info* info, const std
     if(dev)
     {
         CMSmallARGBController*               controller     = new CMSmallARGBController(dev, info->path);
+
+        if(controller->GetVersion() != "Unsupported")
+        {
             RGBController_CMSmallARGBController* rgb_controller = new RGBController_CMSmallARGBController(controller);
 
             detected_controllers.push_back(rgb_controller);
         }
+        else
+        {
+            LOG_ERROR("[CMSmallARGBController] Unsupported firmware version");
+            delete controller;
+        }
+    }
 
     return(detected_controllers);
 }

Controllers/CorsairLightingNodeController/CorsairLightingNodeController.cpp

@@ -232,7 +232,7 @@ void CorsairLightingNodeController::SendFirmwareRequest()
     /*-----------------------------------------------------*\
     | Send packet                                           |
     \*-----------------------------------------------------*/
-    actual = WriteAndRead(usb_buf);
+    actual = WriteAndRead(usb_buf, CORSAIR_LIGHTING_NODE_READ_TIMEOUT);
 
     if(actual > 0)
     {

Controllers/CorsairPeripheralController/CorsairPeripheralControllerDetect.cpp

@@ -81,6 +81,7 @@
 #define CORSAIR_SCIMITAR_PRO_RGB_PID    0x1B3E
 #define CORSAIR_SCIMITAR_ELITE_RGB_PID  0x1B8B
 #define CORSAIR_SABRE_RGB_PID           0x1B2F
+#define CORSAIR_SABRE_RGB_OPTICAL_PID   0x1B32
 
 /*---------------------------------------------------------*\
 | Mousepad product IDs                                      |
@@ -215,6 +216,7 @@ REGISTER_HID_DETECTOR_IP("Corsair Scimitar RGB",            DetectCorsairPeriphe
 REGISTER_HID_DETECTOR_IP("Corsair Scimitar PRO RGB",        DetectCorsairPeripheralControllers, CORSAIR_VID, CORSAIR_SCIMITAR_PRO_RGB_PID,   1, 0xFFC2);
 REGISTER_HID_DETECTOR_IP("Corsair Scimitar Elite RGB",      DetectCorsairPeripheralControllers, CORSAIR_VID, CORSAIR_SCIMITAR_ELITE_RGB_PID, 1, 0xFFC2);
 REGISTER_HID_DETECTOR_IP("Corsair Sabre RGB",               DetectCorsairPeripheralControllers, CORSAIR_VID, CORSAIR_SABRE_RGB_PID,          1, 0xFFC2);
+REGISTER_HID_DETECTOR_IP("Corsair Sabre RGB Optical",       DetectCorsairPeripheralControllers, CORSAIR_VID, CORSAIR_SABRE_RGB_OPTICAL_PID,  1, 0xFFC2);
 
 /*---------------------------------------------------------*\
 | Mousemats                                                 |

Controllers/CorsairPeripheralV2Controller/CorsairPeripheralV2Controller.cpp

@@ -29,6 +29,18 @@ CorsairPeripheralV2Controller::CorsairPeripheralV2Controller(hid_device* dev_han
     |   If the PID is in the know wireless receivers list       |
     |   switch the write_cmd to talk to the device and retry    |
     \*---------------------------------------------------------*/
+    /*---------------------------------------------------------*\
+    | Establish the packet size before talking to the device.   |
+    \*---------------------------------------------------------*/
+    uint16_t report_size = GetOutputReportSize();
+
+    if(report_size >= CORSAIR_V2_WRITE_SIZE && report_size <= CORSAIR_V2_PACKET_SIZE)
+    {
+        pkt_sze = report_size;
+    }
+
+    LOG_DEBUG("[%s] Packet length set to %d", device_name.c_str(), pkt_sze);
+
     unsigned int pid    = GetAddressRetry(0x12);
 
     switch(pid)
@@ -64,14 +76,12 @@ CorsairPeripheralV2Controller::CorsairPeripheralV2Controller(hid_device* dev_han
     |   the device being set up.                                |
     \*---------------------------------------------------------*/
     uint8_t buffer[CORSAIR_V2_PACKET_SIZE];
+    memset(buffer, 0, pkt_sze);
     buffer[1] = write_cmd;
     buffer[2] = CORSAIR_V2_CMD_GET;
     buffer[3] = 0x11;
-    hid_write(dev, buffer, CORSAIR_V2_WRITE_SIZE);
-    uint16_t result = hid_read_timeout(dev, buffer, CORSAIR_V2_PACKET_SIZE, CORSAIR_V2_TIMEOUT);
-    result++;
-    pkt_sze = std::max(result, (uint16_t)CORSAIR_V2_WRITE_SIZE);
-    LOG_DEBUG("[%s] Packet length set to %d", device_name.c_str(), pkt_sze);
+    hid_write(dev, buffer, pkt_sze);
+    hid_read_timeout(dev, buffer, pkt_sze, CORSAIR_V2_TIMEOUT);
 
     /*---------------------------------------------------------*\
     | NB: If the device is not found in the device list         |
@@ -108,23 +118,116 @@ CorsairPeripheralV2Controller::CorsairPeripheralV2Controller(hid_device* dev_han
         return;
     }
 
+}
+
 /*---------------------------------------------------------*\
 | Check lighting control endpoints                          |
 |   If lighting control endpoint 2 is unavailable           |
 |   then use endpoint 1.                                    |
 \*---------------------------------------------------------*/
-    if(light_ctrl == CORSAIR_V2_LIGHT_CTRL2)
+uint16_t CorsairPeripheralV2Controller::GetOutputReportSize()
 {
-        result = StartTransaction(0);
-        if(result > 0)
+    unsigned char   descriptor[HID_API_MAX_REPORT_DESCRIPTOR_SIZE];
+    int             length          = hid_get_report_descriptor(dev, descriptor, sizeof(descriptor));
+
+    if(length <= 0)
     {
+        return 0;
+    }
+
+    unsigned int    report_size     = 0;
+    unsigned int    report_count    = 0;
+    int             index           = 0;
+
+    while(index < length)
+    {
+        unsigned char   item        = descriptor[index];
+        unsigned char   tag         = item & 0xFC;
+        unsigned char   item_size   = item & 0x03;
+
+        /*---------------------------------------------------------*\
+        | A size field of 3 means four data bytes follow.           |
+        \*---------------------------------------------------------*/
+        if(item_size == 3)
+        {
+            item_size = 4;
+        }
+
+        if(index + 1 + item_size > length)
+        {
+            break;
+        }
+
+        unsigned int    value       = 0;
+
+        for(unsigned char byte = 0; byte < item_size; byte++)
+        {
+            value |= (unsigned int)descriptor[index + 1 + byte] << (8 * byte);
+        }
+
+        switch(tag)
+        {
+            case 0x74:                              /* Report Size      */
+                report_size     = value;
+                break;
+
+            case 0x94:                              /* Report Count     */
+                report_count    = value;
+                break;
+
+            case 0x90:                              /* Output           */
+                if(report_size > 0 && report_count > 0)
+                {
+                    return (uint16_t)(((report_size * report_count) / 8) + 1);
+                }
+                break;
+        }
+
+        index += 1 + item_size;
+    }
+
+    return 0;
+}
+
+void CorsairPeripheralV2Controller::DetectLightingEndpoint()
+{
+    /*---------------------------------------------------------*\
+    | A device that cannot be read from cannot be probed; those |
+    |   carry the endpoint they need already set.               |
+    \*---------------------------------------------------------*/
+    if(skip_reads)
+    {
+        return;
+    }
+
+    /*---------------------------------------------------------*\
+    | Lighting control 1 is the plain lighting resource and     |
+    |   takes colour block data.  A device that answers         |
+    |   invalid or unsupported for it wants the alternate       |
+    |   lighting resource, which takes RGB triplets.            |
+    \*---------------------------------------------------------*/
     light_ctrl              = CORSAIR_V2_LIGHT_CTRL1;
+    unsigned char result    = StartTransaction(0);
+
+    /*---------------------------------------------------------*\
+    | A handle left open by an earlier session answers failed;  |
+    |   close it and open it again.                             |
+    \*---------------------------------------------------------*/
+    if(result == CORSAIR_V2_ERR_FAILED)
+    {
+        StopTransaction(0);
+        result              = StartTransaction(0);
+    }
+
+    if(result == CORSAIR_V2_ERR_INVALID || result == CORSAIR_V2_ERR_NOT_SUPPORTED)
+    {
+        light_ctrl          = CORSAIR_V2_LIGHT_CTRL2;
         StartTransaction(0);
     }
+
     StopTransaction(0);
     LOG_DEBUG("[%s] Lighting Endpoint set to %02X", device_name.c_str(), light_ctrl);
 }
-}
 
 CorsairPeripheralV2Controller::~CorsairPeripheralV2Controller()
 {
@@ -191,9 +294,9 @@ std::string CorsairPeripheralV2Controller::GetSerialString()
 
 void CorsairPeripheralV2Controller::SetRenderMode(corsair_v2_device_mode mode)
 {
-    uint8_t buffer[CORSAIR_V2_WRITE_SIZE];
+    uint8_t buffer[CORSAIR_V2_PACKET_SIZE];
 
-    memset(buffer, 0, CORSAIR_V2_WRITE_SIZE);
+    memset(buffer, 0, pkt_sze);
 
     /*---------------------------------------------------------*\
     | Set Mode                                                  |
@@ -203,19 +306,19 @@ void CorsairPeripheralV2Controller::SetRenderMode(corsair_v2_device_mode mode)
     buffer[3]   = CORSAIR_V2_VALUE_MODE;
     buffer[5]   = mode;
 
-    hid_write(dev, buffer, CORSAIR_V2_WRITE_SIZE);
+    hid_write(dev, buffer, pkt_sze);
 
     if(!skip_reads)
     {
-        hid_read_timeout(dev, buffer, CORSAIR_V2_WRITE_SIZE, CORSAIR_V2_TIMEOUT);
+        hid_read_timeout(dev, buffer, pkt_sze, CORSAIR_V2_TIMEOUT);
     }
 }
 
 void CorsairPeripheralV2Controller::LightingControl(uint8_t opt1)
 {
-    uint8_t buffer[CORSAIR_V2_WRITE_SIZE];
+    uint8_t buffer[CORSAIR_V2_PACKET_SIZE];
 
-    memset(buffer, 0, CORSAIR_V2_WRITE_SIZE);
+    memset(buffer, 0, pkt_sze);
 
     /*---------------------------------------------------------*\
     | The Corsair command is the same for each initialisation   |
@@ -227,11 +330,11 @@ void CorsairPeripheralV2Controller::LightingControl(uint8_t opt1)
     buffer[3]   = opt1;
     buffer[5]   = 0x00;
 
-    hid_write(dev, buffer, CORSAIR_V2_WRITE_SIZE);
+    hid_write(dev, buffer, pkt_sze);
 
     if(!skip_reads)
     {
-        hid_read_timeout(dev, buffer, CORSAIR_V2_WRITE_SIZE, CORSAIR_V2_TIMEOUT);
+        hid_read_timeout(dev, buffer, pkt_sze, CORSAIR_V2_TIMEOUT);
     }
 }
 
@@ -270,18 +373,18 @@ unsigned int CorsairPeripheralV2Controller::GetAddressRetry(uint8_t address)
 
 unsigned int CorsairPeripheralV2Controller::GetAddress(uint8_t address)
 {
-    uint8_t buffer[CORSAIR_V2_WRITE_SIZE];
-    uint8_t read[CORSAIR_V2_WRITE_SIZE];
+    uint8_t buffer[CORSAIR_V2_PACKET_SIZE];
+    uint8_t read[CORSAIR_V2_PACKET_SIZE];
 
-    memset(buffer, 0, CORSAIR_V2_WRITE_SIZE);
-    memset(read, 0, CORSAIR_V2_WRITE_SIZE);
+    memset(buffer, 0, pkt_sze);
+    memset(read, 0, pkt_sze);
 
     buffer[1]   = write_cmd;
     buffer[2]   = CORSAIR_V2_CMD_GET;
     buffer[3]   = address;
 
-    hid_write(dev, buffer, CORSAIR_V2_WRITE_SIZE);
-    hid_read_timeout(dev, read, CORSAIR_V2_WRITE_SIZE, CORSAIR_V2_TIMEOUT);
+    hid_write(dev, buffer, pkt_sze);
+    hid_read_timeout(dev, read, pkt_sze, CORSAIR_V2_TIMEOUT);
 
     unsigned int temp = (unsigned int)(read[6] << 24 | read[5] << 16 | read[4] << 8 | read[3]);
     LOG_DEBUG("[%s] GetAddress %02X - %02X %02X - %02X %02X %02X %02X   %02X %02X %02X %02X", device_name.c_str(),
@@ -299,20 +402,20 @@ unsigned int CorsairPeripheralV2Controller::GetAddress(uint8_t address)
 
 unsigned char CorsairPeripheralV2Controller::StartTransaction(uint8_t opt1)
 {
-    uint8_t buffer[CORSAIR_V2_WRITE_SIZE];
+    uint8_t buffer[CORSAIR_V2_PACKET_SIZE];
 
-    memset(buffer, 0, CORSAIR_V2_WRITE_SIZE);
+    memset(buffer, 0, pkt_sze);
 
     buffer[1]   = write_cmd;
     buffer[2]   = CORSAIR_V2_CMD_START_TX;
     buffer[3]   = opt1;
     buffer[4]   = light_ctrl;
 
-    hid_write(dev, buffer, CORSAIR_V2_WRITE_SIZE);
+    hid_write(dev, buffer, pkt_sze);
 
     if(!skip_reads)
     {
-        hid_read_timeout(dev, buffer, CORSAIR_V2_WRITE_SIZE, CORSAIR_V2_TIMEOUT);
+        hid_read_timeout(dev, buffer, pkt_sze, CORSAIR_V2_TIMEOUT);
     }
 
     return buffer[2];
@@ -320,20 +423,20 @@ unsigned char CorsairPeripheralV2Controller::StartTransaction(uint8_t opt1)
 
 void CorsairPeripheralV2Controller::StopTransaction(uint8_t opt1)
 {
-    uint8_t buffer[CORSAIR_V2_WRITE_SIZE];
+    uint8_t buffer[CORSAIR_V2_PACKET_SIZE];
 
-    memset(buffer, 0, CORSAIR_V2_WRITE_SIZE);
+    memset(buffer, 0, pkt_sze);
 
     buffer[1]   = write_cmd;
     buffer[2]   = CORSAIR_V2_CMD_STOP_TX;
     buffer[3]   = 0x01;
     buffer[4]   = opt1;
 
-    hid_write(dev, buffer, CORSAIR_V2_WRITE_SIZE);
+    hid_write(dev, buffer, pkt_sze);
 
     if(!skip_reads)
     {
-        hid_read_timeout(dev, buffer, CORSAIR_V2_WRITE_SIZE, CORSAIR_V2_TIMEOUT);
+        hid_read_timeout(dev, buffer, pkt_sze, CORSAIR_V2_TIMEOUT);
     }
 }
 
@@ -347,6 +450,11 @@ void CorsairPeripheralV2Controller::ClearPacketBuffer()
     uint8_t result          = 0;
     uint8_t buffer[CORSAIR_V2_PACKET_SIZE];
 
+    /*---------------------------------------------------------*\
+    | Draining expects to find nothing, so the last read here    |
+    |   always waits out the timeout.  Keep it short: this runs  |
+    |   before every LED update.                                 |
+    \*---------------------------------------------------------*/
     do
     {
         result = hid_read_timeout(dev, buffer, pkt_sze, CORSAIR_V2_TIMEOUT_SHORT);
@@ -356,6 +464,8 @@ void CorsairPeripheralV2Controller::ClearPacketBuffer()
 
 void CorsairPeripheralV2Controller::SetLEDs(uint8_t *data, uint16_t data_size)
 {
+    std::lock_guard<std::mutex> lock(device_mutex);
+
     const uint8_t offset1   = 8;
     const uint8_t offset2   = 4;
     uint16_t remaining      = data_size;
@@ -389,7 +499,7 @@ void CorsairPeripheralV2Controller::SetLEDs(uint8_t *data, uint16_t data_size)
 
     if(!skip_reads)
     {
-        hid_read_timeout(dev, buffer, pkt_sze, CORSAIR_V2_TIMEOUT_SHORT);
+        hid_read_timeout(dev, buffer, pkt_sze, CORSAIR_V2_TIMEOUT);
     }
 
     remaining              -= copy_bytes;
@@ -414,7 +524,7 @@ void CorsairPeripheralV2Controller::SetLEDs(uint8_t *data, uint16_t data_size)
 
         if(!skip_reads)
         {
-            hid_read_timeout(dev, buffer, pkt_sze, CORSAIR_V2_TIMEOUT_SHORT);
+            hid_read_timeout(dev, buffer, pkt_sze, CORSAIR_V2_TIMEOUT);
         }
 
         remaining          -= copy_bytes;
@@ -426,6 +536,8 @@ void CorsairPeripheralV2Controller::SetLEDs(uint8_t *data, uint16_t data_size)
 void CorsairPeripheralV2Controller::UpdateHWMode(uint16_t mode, corsair_v2_color /*color_mode*/, uint8_t /*speed*/,
                                                  uint8_t /*direction*/, uint8_t /*brightness*/, std::vector<RGBColor> /*colors*/)
 {
+    std::lock_guard<std::mutex> lock(device_mutex);
+
     /*---------------------------------------------------------*\
     | If we are switching to `Direct` mode                      |
     |   set device in software mode                             |

Controllers/CorsairPeripheralV2Controller/CorsairPeripheralV2Controller.h

@@ -12,6 +12,7 @@
 #pragma once
 
 #include <string>
+#include <mutex>
 #include <vector>
 #include <hidapi.h>
 #include "LogManager.h"
@@ -21,13 +22,33 @@
 #define NA                              0xFFFFFFFF
 #define HID_MAX_STR                     255
 
-#define CORSAIR_V2_TIMEOUT              50
+/*---------------------------------------------------------*\
+| A jumbo packet device answers a 1KB command in well over  |
+|   50ms.  Missing the reply leaves it queued and the next  |
+|   write to the device then fails outright, so this has to |
+|   be generous.  A reply that does arrive is returned as   |
+|   soon as it lands, so this only costs time on failure.   |
+\*---------------------------------------------------------*/
+#define CORSAIR_V2_TIMEOUT              500
 #define CORSAIR_V2_TIMEOUT_SHORT        3
 #define CORSAIR_V2_VALUE_MODE           3
 #define CORSAIR_V2_WRITE_WIRED_ID       8
 #define CORSAIR_V2_WRITE_WIRELESS_ID    9
 #define CORSAIR_V2_WRITE_SIZE           65
-#define CORSAIR_V2_PACKET_SIZE          1024
+/*---------------------------------------------------------*\
+| Largest packet the protocol uses: 1024 payload bytes      |
+|   plus the leading report ID.  pkt_sze is measured        |
+|   against this, and every stack buffer handed to hidapi   |
+|   with pkt_sze is this size, so the two must agree.       |
+\*---------------------------------------------------------*/
+#define CORSAIR_V2_PACKET_SIZE          1025
+
+/*---------------------------------------------------------*\
+| Error codes the device returns in byte 2 of a reply.      |
+\*---------------------------------------------------------*/
+#define CORSAIR_V2_ERR_INVALID          0x01
+#define CORSAIR_V2_ERR_FAILED           0x03
+#define CORSAIR_V2_ERR_NOT_SUPPORTED    0x06
 
 #define CORSAIR_V2_LIGHT_CTRL1          1
 #define CORSAIR_V2_LIGHT_CTRL2          34          /* 0x22                             */
@@ -113,6 +134,27 @@ protected:
     std::string                     device_name;
     uint8_t                         light_ctrl          = CORSAIR_V2_LIGHT_CTRL2;
 
+    /*---------------------------------------------------------*\
+    | Works out which lighting control endpoint the device       |
+    |   accepts.  Must be called only once the device has been   |
+    |   put into software render mode: endpoint 2 rejects the    |
+    |   transaction while the device is still driving its own    |
+    |   lighting, which would pick endpoint 1 for a device that  |
+    |   does not support it.                                     |
+    \*---------------------------------------------------------*/
+    void                            DetectLightingEndpoint();
+
+    /*---------------------------------------------------------*\
+    | Size of one output report, plus the leading report ID.     |
+    |   Read from the HID report descriptor before anything is   |
+    |   sent: these devices come in a 64 byte and a 1024 byte    |
+    |   flavour, and sending a short packet to a 1024 byte       |
+    |   endpoint wedges it until the device is reset, so the     |
+    |   size has to be known before the first write rather than  |
+    |   inferred from a reply.  Returns 0 if it cannot be read.  |
+    \*---------------------------------------------------------*/
+    uint16_t                        GetOutputReportSize();
+
 private:
     void                            ClearPacketBuffer();
     unsigned int                    GetAddress(uint8_t address);
@@ -122,6 +164,16 @@ private:
 
     hid_device*                     dev;
 
+    /*---------------------------------------------------------*\
+    | Serialises device transactions.                           |
+    |   The RGB controllers run a keepalive thread that writes  |
+    |   LEDs independently of the caller, and a Corsair block   |
+    |   write spans several packets.  Letting two of those      |
+    |   interleave on one HID handle corrupts the transaction   |
+    |   and leaves the device unresponsive until it is reset.   |
+    \*---------------------------------------------------------*/
+    std::mutex                      device_mutex;
+
     uint8_t                         write_cmd           = CORSAIR_V2_WRITE_WIRED_ID;
     uint16_t                        pkt_sze             = CORSAIR_V2_WRITE_SIZE;
     bool                            skip_reads          = false;

Controllers/CorsairPeripheralV2Controller/CorsairPeripheralV2ControllerDetect.cpp

@@ -92,6 +92,7 @@ DetectedControllers DetectCorsairV2SoftwareControllers(hid_device_info* info, co
 REGISTER_HID_DETECTOR_IP("Corsair K55 RGB PRO",                     DetectCorsairV2SoftwareControllers, CORSAIR_VID,    CORSAIR_K55_RGB_PRO_PID,                1,  0xFF42);
 REGISTER_HID_DETECTOR_IP("Corsair K57 RGB (Wired)",                 DetectCorsairV2SoftwareControllers, CORSAIR_VID,    CORSAIR_K57_RGB_WIRED_PID,              1,  0xFF42);
 REGISTER_HID_DETECTOR_IP("Corsair K60 RGB PRO",                     DetectCorsairV2SoftwareControllers, CORSAIR_VID,    CORSAIR_K60_RGB_PRO_PID,                1,  0xFF42);
+REGISTER_HID_DETECTOR_IP("Corsair K60 RGB PRO SE",                  DetectCorsairV2SoftwareControllers, CORSAIR_VID,    CORSAIR_K60_RGB_PRO_SE_PID,             1,  0xFF42);
 REGISTER_HID_DETECTOR_IP("Corsair K60 RGB PRO Low Profile",         DetectCorsairV2SoftwareControllers, CORSAIR_VID,    CORSAIR_K60_RGB_PRO_LP_PID,             1,  0xFF42);
 REGISTER_HID_DETECTOR_IP("Corsair K60 RGB PRO TKL Black",           DetectCorsairV2HardwareControllers, CORSAIR_VID,    CORSAIR_K60_RGB_PRO_TKL_B_PID,          1,  0xFF42);
 REGISTER_HID_DETECTOR_IP("Corsair K60 RGB PRO TKL White",           DetectCorsairV2HardwareControllers, CORSAIR_VID,    CORSAIR_K60_RGB_PRO_TKL_W_PID,          1,  0xFF42);

Controllers/CorsairPeripheralV2Controller/CorsairPeripheralV2Devices.cpp

@@ -901,7 +901,7 @@ static const corsair_v2_device k57_rgb_wired_device =
 |                                                               |
 |  Zone "Keyboard"                                              |
 |       Matrix                                                  |
-|       6 Rows, 21 Columns                                      |
+|       7 Rows, 22 Columns                                      |
 \*-------------------------------------------------------------*/
 static const corsair_v2_zone k60_rgb_pro_zone =
 {
@@ -928,12 +928,34 @@ static const corsair_v2_device k60_rgb_pro_device =
     &corsair_K60_layout
 };
 
+/*-------------------------------------------------------------*\
+|  Corsair K60 RGB Pro SE 1B1C:1B8D                             |
+|                                                               |
+|  Initial implementation reuses K60 RGB Pro zone/layout        |
+\*-------------------------------------------------------------*/
+static const corsair_v2_device k60_rgb_pro_se_device =
+{
+    CORSAIR_K60_RGB_PRO_SE_PID,
+    DEVICE_TYPE_KEYBOARD,
+    6,
+    21,
+    {
+        &k60_rgb_pro_zone,
+        nullptr,
+        nullptr,
+        nullptr,
+        nullptr,
+        nullptr
+    },
+    &corsair_K60_layout
+};
+
 /*-------------------------------------------------------------*\
 |  Corsair K60 RGB Pro Low Profile 1B1C:1BAD                    |
 |                                                               |
 |  Zone "Keyboard"                                              |
 |       Matrix                                                  |
-|       6 Rows, 21 Columns                                      |
+|       7 Rows, 22 Columns                                      |
 \*-------------------------------------------------------------*/
 static const corsair_v2_zone k60_rgb_pro_lp_zone =
 {
@@ -966,7 +988,7 @@ static const corsair_v2_device k60_rgb_pro_lp_device =
 |                                                               |
 |  Zone "Keyboard"                                              |
 |       Matrix                                                  |
-|       6 Rows, 21 Columns                                      |
+|       7 Rows, 22 Columns                                      |
 \*-------------------------------------------------------------*/
 static const corsair_v2_zone k60_rgb_pro_tkl_zone =
 {
@@ -1016,7 +1038,7 @@ static const corsair_v2_device k60_rgb_pro_tkl_device_w =
 |                                                               |
 |  Zone "Keyboard"                                              |
 |       Matrix                                                  |
-|       6 Rows, 21 Columns                                      |
+|       7 Rows, 22 Columns                                      |
 \*-------------------------------------------------------------*/
 static const corsair_v2_zone k70_core_rgb_zone =
 {
@@ -1145,14 +1167,14 @@ static const corsair_v2_device k70_rgb_tkl_cs_device =
 |                                                               |
 |  Zone "Keyboard"                                              |
 |       Matrix                                                  |
-|       6 Rows, 21 Columns                                      |
+|       7 Rows, 22 Columns                                      |
 \*-------------------------------------------------------------*/
 static const corsair_v2_zone k70_rgb_pro_zone =
 {
     ZONE_EN_KEYBOARD,
     ZONE_TYPE_MATRIX,
     7,
-    21
+    22
 };
 
 static const corsair_v2_device k70_rgb_pro_device =
@@ -1160,7 +1182,7 @@ static const corsair_v2_device k70_rgb_pro_device =
     CORSAIR_K70_RGB_PRO_PID,
     DEVICE_TYPE_KEYBOARD,
     7,
-    21,
+    22,
     {
         &k70_rgb_pro_zone,
         nullptr,
@@ -1177,14 +1199,14 @@ static const corsair_v2_device k70_rgb_pro_device =
 |                                                               |
 |  Zone "Keyboard"                                              |
 |       Matrix                                                  |
-|       6 Rows, 21 Columns                                      |
+|       7 Rows, 22 Columns                                      |
 \*-------------------------------------------------------------*/
 static const corsair_v2_device k70_rgb_pro_v2_device =
     {
         CORSAIR_K70_RGB_PRO_V2_PID,
         DEVICE_TYPE_KEYBOARD,
         7,
-        21,
+        22,
         {
             &k70_rgb_pro_zone,
             nullptr,
@@ -1193,7 +1215,8 @@ static const corsair_v2_device k70_rgb_pro_v2_device =
             nullptr,
             nullptr
         },
-        &corsair_k70_pro_layout
+        &corsair_k70_pro_layout,
+        193
 };
 
 /*-------------------------------------------------------------*\
@@ -1625,6 +1648,7 @@ const corsair_v2_device* corsair_v2_device_list_data[] =
     &k55_rgb_pro_device,
     &k57_rgb_wired_device,
     &k60_rgb_pro_device,
+    &k60_rgb_pro_se_device,
     &k60_rgb_pro_lp_device,
     &k60_rgb_pro_tkl_device_b,
     &k60_rgb_pro_tkl_device_w,

Controllers/CorsairPeripheralV2Controller/CorsairPeripheralV2Devices.h

@@ -63,6 +63,15 @@ typedef struct
     uint8_t                             cols;
     const corsair_v2_zone*              zones[CORSAIR_ZONES_MAX];
     keyboard_keymap_overlay_values*     layout_new;
+    /*-------------------------------------------------------*\
+    | Number of LED slots the device expects in a direct       |
+    |   lighting write.  The keymap only covers the keys that  |
+    |   exist, but the device wants its full slot count and    |
+    |   ignores a short write, so the buffer map is padded up  |
+    |   to this.  Left 0 where the count is not known, which   |
+    |   keeps the keymap derived size.                         |
+    \*-------------------------------------------------------*/
+    uint16_t                            hw_led_count;
 }   corsair_v2_device;
 
 /*-----------------------------------------------------*\
@@ -72,6 +81,7 @@ typedef struct
 #define CORSAIR_K57_RGB_WIRED_PID                   0x1B6E
 #define CORSAIR_K57_RGB_WIRELESS_PID                0x1B62
 #define CORSAIR_K60_RGB_PRO_PID                     0x1BA0
+#define CORSAIR_K60_RGB_PRO_SE_PID                  0x1B8D
 #define CORSAIR_K60_RGB_PRO_LP_PID                  0x1BAD
 #define CORSAIR_K60_RGB_PRO_TKL_B_PID               0x1BC7
 #define CORSAIR_K60_RGB_PRO_TKL_W_PID               0x1BED

Controllers/CorsairPeripheralV2Controller/CorsairPeripheralV2HardwareController.cpp

@@ -16,6 +16,12 @@ CorsairPeripheralV2HWController::CorsairPeripheralV2HWController(hid_device* dev
 {
     SetRenderMode(CORSAIR_V2_MODE_SW);
     LightingControl(0x5F);
+
+    /*---------------------------------------------------------*\
+    | Only now that the device is in software render mode can   |
+    |   its lighting control endpoint be probed reliably.       |
+    \*---------------------------------------------------------*/
+    DetectLightingEndpoint();
 }
 
 CorsairPeripheralV2HWController::~CorsairPeripheralV2HWController()

Controllers/CorsairPeripheralV2Controller/CorsairPeripheralV2SoftwareController.cpp

@@ -16,6 +16,12 @@ CorsairPeripheralV2SWController::CorsairPeripheralV2SWController(hid_device* dev
 {
     SetRenderMode(CORSAIR_V2_MODE_SW);
     LightingControl(0x5F);
+
+    /*---------------------------------------------------------*\
+    | Only now that the device is in software render mode can   |
+    |   its lighting control endpoint be probed reliably.       |
+    \*---------------------------------------------------------*/
+    DetectLightingEndpoint();
 }
 
 CorsairPeripheralV2SWController::~CorsairPeripheralV2SWController()

Controllers/CorsairPeripheralV2Controller/RGBController_CorsairV2Hardware.cpp

@@ -66,21 +66,32 @@ RGBController_CorsairV2HW::RGBController_CorsairV2HW(CorsairPeripheralV2Controll
     | to not revert back into rainbow mode.  Start a thread |
     | to continuously send a keepalive packet every 50 sec  |
     \*-----------------------------------------------------*/
+    /*-----------------------------------------------------*\
+    | Start the keepalive clock before the thread runs.     |
+    |   A default constructed time_point sits at the clock  |
+    |   epoch, which is always older than the update        |
+    |   period, so the thread would otherwise fire a write  |
+    |   on its first pass - during detection, racing        |
+    |   whatever the caller is doing.                       |
+    \*-----------------------------------------------------*/
+    last_update_time                    = std::chrono::steady_clock::now();
+
     keepalive_thread_run                = true;
     keepalive_thread                    = new std::thread(&RGBController_CorsairV2HW::KeepaliveThread, this);
 }
 
 RGBController_CorsairV2HW::~RGBController_CorsairV2HW()
 {
-    Shutdown();
-
     /*-----------------------------------------------------*\
-    | Close keepalive thread                                |
+    | Close keepalive thread first, so that it cannot issue |
+    |   a write while the device is being shut down.        |
     \*-----------------------------------------------------*/
     keepalive_thread_run = false;
     keepalive_thread->join();
     delete keepalive_thread;
 
+    Shutdown();
+
     delete controller;
 }
 
@@ -198,6 +209,15 @@ void RGBController_CorsairV2HW::SetupZones()
 
     SetupColors();
 
+    /*---------------------------------------------------------*\
+    | Pad out to the slot count the device expects.  A write    |
+    |   that is short of it is ignored by the hardware.         |
+    \*---------------------------------------------------------*/
+    if(corsair->hw_led_count > max_led_value)
+    {
+        max_led_value                   = corsair->hw_led_count;
+    }
+
     /*---------------------------------------------------------*\
     | Create a buffer map of pointers which contains the        |
     |   layout order of colors the device expects.              |

Controllers/CorsairPeripheralV2Controller/RGBController_CorsairV2Software.cpp

@@ -53,21 +53,32 @@ RGBController_CorsairV2SW::RGBController_CorsairV2SW(CorsairPeripheralV2Controll
     | to not revert back into rainbow mode.  Start a thread |
     | to continuously send a keepalive packet every 50 sec  |
     \*-----------------------------------------------------*/
+    /*-----------------------------------------------------*\
+    | Start the keepalive clock before the thread runs.     |
+    |   A default constructed time_point sits at the clock  |
+    |   epoch, which is always older than the update        |
+    |   period, so the thread would otherwise fire a write  |
+    |   on its first pass - during detection, racing        |
+    |   whatever the caller is doing.                       |
+    \*-----------------------------------------------------*/
+    last_update_time                    = std::chrono::steady_clock::now();
+
     keepalive_thread_run                = true;
     keepalive_thread                    = new std::thread(&RGBController_CorsairV2SW::KeepaliveThread, this);
 }
 
 RGBController_CorsairV2SW::~RGBController_CorsairV2SW()
 {
-    Shutdown();
-
     /*-----------------------------------------------------*\
-    | Close keepalive thread                                |
+    | Close keepalive thread first, so that it cannot issue |
+    |   a write while the device is being shut down.        |
     \*-----------------------------------------------------*/
     keepalive_thread_run = false;
     keepalive_thread->join();
     delete keepalive_thread;
 
+    Shutdown();
+
     delete controller;
 }
 
@@ -185,6 +196,15 @@ void RGBController_CorsairV2SW::SetupZones()
 
     SetupColors();
 
+    /*---------------------------------------------------------*\
+    | Pad out to the slot count the device expects.  A write    |
+    |   that is short of it is ignored by the hardware.         |
+    \*---------------------------------------------------------*/
+    if(corsair->hw_led_count > max_led_value)
+    {
+        max_led_value                   = corsair->hw_led_count;
+    }
+
     /*---------------------------------------------------------*\
     | Create a buffer map of pointers which contains the        |
     |   layout order of colors the device expects.              |

Controllers/EVGAUSBController/EVGAX12Controller/EVGAX12Controller.cpp

@@ -26,6 +26,13 @@
 #define EVGA_X12_READ_DELAY_MS              5
 #define EVGA_X12_WRITE_ATTEMPTS             3
 
+static const unsigned int EVGA_X12_LED_TO_FIRMWARE_SLOT[EVGA_X12_LED_COUNT] =
+{
+    EVGA_X12_FIRMWARE_SLOT_HEAD_LEFT,
+    EVGA_X12_FIRMWARE_SLOT_WHEEL,
+    EVGA_X12_FIRMWARE_SLOT_LOGO,
+};
+
 EVGAX12Controller::EVGAX12Controller(hid_device* dev_handle, const hid_device_info& info, const std::string& dev_name)
 {
     dev         = dev_handle;
@@ -73,7 +80,8 @@ EVGAX12LightingState EVGAX12Controller::GetLightingState()
     {
         for(unsigned int led_idx = 0; led_idx < EVGA_X12_LED_COUNT; led_idx++)
         {
-            state.modes[led_idx] = packet[4 + led_idx];
+            unsigned int firmware_slot = EVGA_X12_LED_TO_FIRMWARE_SLOT[led_idx];
+            state.modes[led_idx]        = packet[4 + firmware_slot];
         }
     }
 
@@ -83,7 +91,8 @@ EVGAX12LightingState EVGAX12Controller::GetLightingState()
     {
         for(unsigned int led_idx = 0; led_idx < EVGA_X12_LED_COUNT; led_idx++)
         {
-            unsigned int offset         = 4 + (led_idx * 4);
+            unsigned int firmware_slot  = EVGA_X12_LED_TO_FIRMWARE_SLOT[led_idx];
+            unsigned int offset         = 4 + (firmware_slot * 4);
             state.brightness[led_idx]   = packet[offset];
             state.colors[led_idx]       = ToRGBColor(packet[offset + 1], packet[offset + 2], packet[offset + 3]);
         }
@@ -109,7 +118,8 @@ bool EVGAX12Controller::SetModeReport(unsigned char mode)
 
     for(unsigned int led_idx = 0; led_idx < EVGA_X12_LED_COUNT; led_idx++)
     {
-        packet[4 + led_idx] = mode;
+        unsigned int firmware_slot  = EVGA_X12_LED_TO_FIRMWARE_SLOT[led_idx];
+        packet[4 + firmware_slot]   = mode;
     }
 
     return(SendReport(packet));
@@ -155,14 +165,19 @@ bool EVGAX12Controller::SetStaticReport(const std::vector<RGBColor>& colors, uns
     packet[2] = EVGA_X12_DIRECTION_SET;
     packet[3] = EVGA_X12_COMMAND_STATIC;
 
+    for(unsigned int firmware_slot = 0; firmware_slot < EVGA_X12_FIRMWARE_SLOT_COUNT; firmware_slot++)
+    {
+        packet[20 + firmware_slot] = EVGA_X12_START_WITH_PROFILE;
+    }
+
     for(unsigned int led_idx = 0; led_idx < EVGA_X12_LED_COUNT; led_idx++)
     {
-        unsigned int offset         = 4 + (led_idx * 4);
+        unsigned int firmware_slot  = EVGA_X12_LED_TO_FIRMWARE_SLOT[led_idx];
+        unsigned int offset         = 4 + (firmware_slot * 4);
         packet[offset]              = brightness;
         packet[offset + 1]          = RGBGetRValue(colors[led_idx]);
         packet[offset + 2]          = RGBGetGValue(colors[led_idx]);
         packet[offset + 3]          = RGBGetBValue(colors[led_idx]);
-        packet[20 + led_idx]        = EVGA_X12_START_WITH_PROFILE;
     }
 
     for(unsigned int attempt = 0; attempt < EVGA_X12_WRITE_ATTEMPTS; attempt++)
@@ -180,9 +195,9 @@ bool EVGAX12Controller::SetStaticReport(const std::vector<RGBColor>& colors, uns
         {
             bool matches = true;
 
-            for(unsigned int led_idx = 0; led_idx < EVGA_X12_LED_COUNT; led_idx++)
+            for(unsigned int firmware_slot = 0; firmware_slot < EVGA_X12_FIRMWARE_SLOT_COUNT; firmware_slot++)
             {
-                unsigned int offset = 4 + (led_idx * 4);
+                unsigned int offset = 4 + (firmware_slot * 4);
 
                 if(std::memcmp(&packet[offset], &reply[offset], 4) != 0)
                 {

Controllers/EVGAUSBController/EVGAX12Controller/EVGAX12Controller.h

@@ -20,7 +20,8 @@
 
 #define EVGA_X12_REPORT_ID                  0x07
 #define EVGA_X12_REPORT_SIZE                40
-#define EVGA_X12_LED_COUNT                  4
+#define EVGA_X12_LED_COUNT                  3
+#define EVGA_X12_FIRMWARE_SLOT_COUNT        4
 #define EVGA_X12_BRIGHTNESS_MIN             0
 #define EVGA_X12_BRIGHTNESS_MAX             255
 
@@ -30,12 +31,16 @@ enum
     EVGA_X12_MODE_STATIC                    = 1,
 };
 
+/*---------------------------------------------------------*\
+| HEAD_LEFT drives both physical side lights. HEAD_RIGHT    |
+| is writable and readable, but has no physical emitter.    |
+\*---------------------------------------------------------*/
 enum
 {
-    EVGA_X12_LED_HEAD_LEFT                  = 0,
-    EVGA_X12_LED_HEAD_RIGHT                 = 1,
-    EVGA_X12_LED_WHEEL                      = 2,
-    EVGA_X12_LED_LOGO                       = 3,
+    EVGA_X12_FIRMWARE_SLOT_HEAD_LEFT        = 0,
+    EVGA_X12_FIRMWARE_SLOT_HEAD_RIGHT       = 1,
+    EVGA_X12_FIRMWARE_SLOT_WHEEL            = 2,
+    EVGA_X12_FIRMWARE_SLOT_LOGO             = 3,
 };
 
 struct EVGAX12LightingState

Controllers/EVGAUSBController/EVGAX12Controller/RGBController_EVGAX12.cpp

@@ -41,14 +41,14 @@ RGBController_EVGAX12::RGBController_EVGAX12(EVGAX12Controller* controller_ptr)
     Direct.brightness_max       = EVGA_X12_BRIGHTNESS_MAX;
     Direct.brightness           = EVGA_X12_BRIGHTNESS_MAX;
     Direct.color_mode           = MODE_COLORS_PER_LED;
-    direct_mode_index           = modes.size();
+    direct_mode_index           = (unsigned int)modes.size();
     modes.push_back(Direct);
 
     mode Off;
     Off.name                    = "Off";
     Off.value                   = EVGA_X12_MODE_OFF;
     Off.color_mode              = MODE_COLORS_NONE;
-    off_mode_index              = modes.size();
+    off_mode_index              = (unsigned int)modes.size();
     modes.push_back(Off);
 
     active_mode                 = direct_mode_index;
@@ -98,8 +98,7 @@ void RGBController_EVGAX12::SetupZones()
 {
     const char* zone_names[EVGA_X12_LED_COUNT] =
     {
-        "Left Head",
-        "Right Head",
+        "Side",
         "Scroll Wheel",
         "Logo",
     };

Controllers/GainwardGPUController/GainwardGPUControllerDetect.cpp

@@ -1,102 +0,0 @@
-/*---------------------------------------------------------*\
-| GainwardGPUControllerDetect.cpp                           |
-|                                                           |
-|   Detector for Gainward GPU                               |
-|                                                           |
-|   TheRogueZeta                                05 Nov 2020 |
-|   KundaPanda                                  04 Jan 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include "DetectionManager.h"
-#include "GainwardGPUv1Controller.h"
-#include "GainwardGPUv2Controller.h"
-#include "i2c_smbus.h"
-#include "pci_ids.h"
-#include "RGBController_GainwardGPUv1.h"
-#include "RGBController_GainwardGPUv2.h"
-
-bool TestForGainwardGPUController(i2c_smbus_interface* bus, uint8_t i2c_addr)
-{
-    bool pass = false;
-
-    switch(i2c_addr)
-    {
-        /*-------------------------------------------------*\
-        | V1 Controller                                     |
-        \*-------------------------------------------------*/
-        case 0x08:
-            pass = bus->i2c_smbus_write_quick(i2c_addr, I2C_SMBUS_WRITE);
-            break;
-
-        /*-------------------------------------------------*\
-        | V2 Controller                                     |
-        \*-------------------------------------------------*/
-        case 0x49:
-            /*---------------------------------------------*\
-            | This detection might need some modifications  |
-            | Reading 0x6F*0x73 and comparing to 0x64 might |
-            | be a possibility                              |
-            \*---------------------------------------------*/
-            s32 data        = bus->i2c_smbus_read_byte_data(i2c_addr, 0x0);
-            s32 mode_data   = bus->i2c_smbus_read_byte_data(i2c_addr, 0xe0);
-            pass            = (data == 0x0) && (mode_data < 0x5);
-            break;
-    }
-
-    return(pass);
-}
-
-DetectedControllers DetectGainwardGPUControllers(i2c_smbus_interface* bus, uint8_t i2c_addr, const std::string& name)
-{
-    DetectedControllers detected_controllers;
-
-    if(TestForGainwardGPUController(bus, i2c_addr))
-    {
-        switch(i2c_addr)
-        {
-            /*---------------------------------------------*\
-            | V1 Controller                                 |
-            \*---------------------------------------------*/
-            case 0x08:
-                {
-                    GainwardGPUv1Controller*     controller     = new GainwardGPUv1Controller(bus, i2c_addr, name);
-                    RGBController_GainwardGPUv1* rgb_controller = new RGBController_GainwardGPUv1(controller);
-
-                    detected_controllers.push_back(rgb_controller);
-                }
-                break;
-
-            /*---------------------------------------------*\
-            | V2 Controller                                 |
-            \*---------------------------------------------*/
-            case 0x49:
-                {
-                    GainwardGPUv2Controller*     controller     = new GainwardGPUv2Controller(bus, i2c_addr, name);
-                    RGBController_GainwardGPUv2* rgb_controller = new RGBController_GainwardGPUv2(controller);
-
-                    detected_controllers.push_back(rgb_controller);
-                }
-                break;
-        }
-    }
-
-    return(detected_controllers);
-}
-
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce GTX 1080 Phoenix",          DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_GTX1080_DEV,     GAINWARD_SUB_VEN,   GAINWARD_GTX_1080_PHOENIX,      0x08);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce GTX 1080 Ti Phoenix",       DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_GTX1080TI_DEV,   GAINWARD_SUB_VEN,   GAINWARD_GTX_1080TI_PHOENIX,    0x08);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce GTX 1660 SUPER Ghost",      DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_GTX1660S_DEV,    NVIDIA_SUB_VEN,     NVIDIA_GTX1660S_DEV,            0x49);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 2070 SUPER Phantom",    DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_RTX2070S_OC_DEV, GAINWARD_SUB_VEN,   NVIDIA_RTX2070S_OC_DEV,         0x49);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 2080 Phoenix GS",       DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_RTX2080_DEV,     GAINWARD_SUB_VEN,   NVIDIA_RTX2080_A_DEV,           0x49);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3060 Pegasus 12G",      DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_RTX3060_DEV,     NVIDIA_SUB_VEN,     NVIDIA_RTX3060_DEV,             0x49);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3070 Phantom",          DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_RTX3070_DEV,     GAINWARD_SUB_VEN,   GAINWARD_RTX_3070_PHANTOM,      0x49);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3070 Phoenix",          DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_RTX3070_DEV,     GAINWARD_SUB_VEN,   NVIDIA_RTX3070_DEV,             0x49);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3070 Ti Phoenix",       DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_RTX3070TI_DEV,   GAINWARD_SUB_VEN,   NVIDIA_RTX3070TI_DEV,           0x49);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3080 Phoenix",          DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_RTX3080_DEV,     GAINWARD_SUB_VEN,   NVIDIA_RTX3080_DEV,             0x49);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3080 Ti Phoenix",       DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_RTX3080TI_DEV,   GAINWARD_SUB_VEN,   NVIDIA_RTX3080TI_DEV,           0x49);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3090 Phoenix",          DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_RTX3090_DEV,     GAINWARD_SUB_VEN,   NVIDIA_RTX3090_DEV,             0x49);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3090 Ti Phantom",       DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_RTX3090TI_DEV,   GAINWARD_SUB_VEN,   GAINWARD_RTX_3090TI_PHANTOM,    0x49);
-REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 4080 Phantom GS",       DetectGainwardGPUControllers,   NVIDIA_VEN, NVIDIA_RTX4080_DEV,     GAINWARD_SUB_VEN,   GAINWARD_RTX_4080_PHANTOM_GS_SUB_DEV,   0x49);

Controllers/GainwardGPUController/GainwardGPUv1Controller/GainwardGPUv1Controller.cpp

@@ -1,78 +0,0 @@
-/*---------------------------------------------------------*\
-| GainwardGPUv1Controller.cpp                               |
-|                                                           |
-|   Driver for Gainward v1 GPU                              |
-|                                                           |
-|   TheRogueZeta                                05 Nov 2020 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include <cstring>
-#include "GainwardGPUv1Controller.h"
-
-GainwardGPUv1Controller::GainwardGPUv1Controller(i2c_smbus_interface* bus, gainward_gpu_dev_id dev, std::string dev_name)
-{
-    this->bus   = bus;
-    this->dev   = dev;
-    this->name  = dev_name;
-}
-
-GainwardGPUv1Controller::~GainwardGPUv1Controller()
-{
-
-}
-
-std::string GainwardGPUv1Controller::GetDeviceLocation()
-{
-    std::string return_string(bus->info.device_name);
-    char addr[5];
-    snprintf(addr, 5, "0x%02X", dev);
-    return_string.append(", address ");
-    return_string.append(addr);
-    return("I2C: " + return_string);
-}
-
-std::string GainwardGPUv1Controller::GetDeviceName()
-{
-    return(name);
-}
-
-unsigned char GainwardGPUv1Controller::GetLEDRed()
-{
-    return(GainwardGPURegisterRead(GAINWARD_RED_REGISTER));
-}
-
-unsigned char GainwardGPUv1Controller::GetLEDGreen()
-{
-    return(GainwardGPURegisterRead(GAINWARD_GREEN_REGISTER));
-}
-
-unsigned char GainwardGPUv1Controller::GetLEDBlue()
-{
-    return(GainwardGPURegisterRead(GAINWARD_BLUE_REGISTER));
-}
-
-void GainwardGPUv1Controller::SetLEDColors(unsigned char red, unsigned char green, unsigned char blue)
-{
-    GainwardGPURegisterWrite(GAINWARD_RED_REGISTER, red);
-    GainwardGPURegisterWrite(GAINWARD_GREEN_REGISTER, green);
-    GainwardGPURegisterWrite(GAINWARD_BLUE_REGISTER, blue);
-    GainwardGPURegisterWrite(GAINWARD_06_REGISTER, 0xFF);
-}
-
-void GainwardGPUv1Controller::SetMode()
-{
-
-}
-
-unsigned char GainwardGPUv1Controller::GainwardGPURegisterRead(unsigned char reg)
-{
-    return(bus->i2c_smbus_read_byte_data(dev, reg));
-}
-
-void GainwardGPUv1Controller::GainwardGPURegisterWrite(unsigned char reg, unsigned char val)
-{
-    bus->i2c_smbus_write_byte_data(dev, reg, val);
-}

Controllers/GainwardGPUController/GainwardGPUv1Controller/RGBController_GainwardGPUv1.cpp

@@ -1,115 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_GainwardGPUv1.cpp                           |
-|                                                           |
-|   RGBController for Gainward v1 GPU                       |
-|                                                           |
-|   TheRogueZeta                                05 Nov 2020 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include "RGBController_GainwardGPUv1.h"
-
-int RGBController_GainwardGPUv1::GetDeviceMode()
-{
-    active_mode = 1;
-    return(active_mode);
-}
-
-/**------------------------------------------------------------------*\
-    @name Gainward GPU v1
-    @category GPU
-    @type I2C
-    @save :x:
-    @direct :white_check_mark:
-    @effects :x:
-    @detectors DetectGainwardGPUControllers
-    @comment
-\*-------------------------------------------------------------------*/
-
-RGBController_GainwardGPUv1::RGBController_GainwardGPUv1(GainwardGPUv1Controller* controller_ptr)
-{
-    controller              = controller_ptr;
-
-    name                    = controller->GetDeviceName();
-    vendor                  = "Gainward";
-    type                    = DEVICE_TYPE_GPU;
-    description             = "Gainward GPU V1 Device";
-    location                = controller->GetDeviceLocation();
-
-    mode Direct;
-    Direct.name             = "Direct";
-    Direct.value            = 1;
-    Direct.flags            = MODE_FLAG_HAS_PER_LED_COLOR;
-    Direct.color_mode       = MODE_COLORS_PER_LED;
-    modes.push_back(Direct);
-
-    SetupZones();
-}
-
-RGBController_GainwardGPUv1::~RGBController_GainwardGPUv1()
-{
-    Shutdown();
-
-    delete controller;
-}
-
-void RGBController_GainwardGPUv1::SetupZones()
-{
-    /*---------------------------------------------------------*\
-    | Set up zone                                               |
-    \*---------------------------------------------------------*/
-    zone gainward_gpu_zone;
-    gainward_gpu_zone.name              = "GPU";
-    gainward_gpu_zone.type              = ZONE_TYPE_SINGLE;
-    gainward_gpu_zone.leds_min          = 1;
-    gainward_gpu_zone.leds_max          = 1;
-    gainward_gpu_zone.leds_count        = 1;
-    zones.push_back(gainward_gpu_zone);
-
-    /*---------------------------------------------------------*\
-    | Set up LED                                                |
-    \*---------------------------------------------------------*/
-    led gainward_gpu_led;
-    gainward_gpu_led.name               = "GPU";
-    leds.push_back(gainward_gpu_led);
-
-    SetupColors();
-
-    /*---------------------------------------------------------*\
-    | Initialize color                                          |
-    \*---------------------------------------------------------*/
-    unsigned char red = controller->GetLEDRed();
-    unsigned char grn = controller->GetLEDGreen();
-    unsigned char blu = controller->GetLEDBlue();
-
-    colors[0] =  ToRGBColor(red, grn, blu);
-}
-
-void RGBController_GainwardGPUv1::DeviceUpdateLEDs()
-{
-    for(std::size_t led = 0; led < colors.size(); led++)
-    {
-        unsigned char red = RGBGetRValue(colors[led]);
-        unsigned char grn = RGBGetGValue(colors[led]);
-        unsigned char blu = RGBGetBValue(colors[led]);
-
-        controller->SetLEDColors(red, grn, blu);
-    }
-}
-
-void RGBController_GainwardGPUv1::DeviceUpdateZoneLEDs(int /*zone*/)
-{
-    DeviceUpdateLEDs();
-}
-
-void RGBController_GainwardGPUv1::DeviceUpdateSingleLED(int /*led*/)
-{
-    DeviceUpdateLEDs();
-}
-
-void RGBController_GainwardGPUv1::DeviceUpdateMode()
-{
-
-}

Controllers/GainwardGPUController/GainwardGPUv2Controller/GainwardGPUv2Controller.cpp

@@ -1,97 +0,0 @@
-/*---------------------------------------------------------*\
-| GainwardGPUv2Controller.cpp                               |
-|                                                           |
-|   Driver for Gainward v2 GPU                              |
-|                                                           |
-|   KundaPanda                                  04 Jan 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include <cstring>
-#include "GainwardGPUv2Controller.h"
-
-GainwardGPUv2Controller::GainwardGPUv2Controller(i2c_smbus_interface* bus, gainward_gpu_dev_id dev, std::string dev_name)
-{
-    this->bus   = bus;
-    this->dev   = dev;
-    this->name  = dev_name;
-}
-
-GainwardGPUv2Controller::~GainwardGPUv2Controller() = default;
-
-std::string GainwardGPUv2Controller::GetDeviceLocation()
-{
-    std::string return_string(bus->info.device_name);
-    char addr[5];
-    snprintf(addr, 5, "0x%02X", dev);
-    return_string.append(", address ");
-    return_string.append(addr);
-    return("I2C: " + return_string);
-}
-
-std::string GainwardGPUv2Controller::GetDeviceName()
-{
-    return(name);
-}
-
-unsigned char GainwardGPUv2Controller::GetLEDRed()
-{
-    return(bus->i2c_smbus_read_byte_data(dev, GAINWARD_V2_RED_REGISTER));
-}
-
-unsigned char GainwardGPUv2Controller::GetLEDGreen()
-{
-    return(bus->i2c_smbus_read_byte_data(dev, GAINWARD_V2_GREEN_REGISTER));
-}
-
-unsigned char GainwardGPUv2Controller::GetLEDBlue()
-{
-    return(bus->i2c_smbus_read_byte_data(dev, GAINWARD_V2_BLUE_REGISTER));
-}
-
-void GainwardGPUv2Controller::SetLEDColors(unsigned char red, unsigned char green, unsigned char blue, unsigned char color_register)
-{
-    switch (color_register)
-    {
-        default:
-            bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_RED_REGISTER, red);
-            bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_GREEN_REGISTER, green);
-            bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_BLUE_REGISTER, blue);
-            break;
-        case GAINWARD_V2_COLOR_REGISTER_SECONDARY:
-            bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_RED_SECONDARY_REGISTER, red);
-            bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_GREEN_SECONDARY_REGISTER, green);
-            bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_BLUE_SECONDARY_REGISTER, blue);
-            break;
-        case GAINWARD_V2_COLOR_REGISTER_TERTIARY:
-            bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_RED_TERTIARY_REGISTER, red);
-            bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_GREEN_TERTIARY_REGISTER, green);
-            bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_BLUE_TERTIARY_REGISTER, blue);
-            break;
-    }
-}
-
-void GainwardGPUv2Controller::SetMode(unsigned char mode, unsigned char speed, unsigned char static_mode)
-{
-    bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_MODE_REGISTER, mode);
-    bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_STATIC_CONTROL_REGISTER, static_mode);
-    bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_SPEED_REGISTER, speed);
-}
-
-void GainwardGPUv2Controller::SetDirection(unsigned char direction)
-{
-    bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_MODE_DIRECTION_REGISTER, direction);
-}
-
-void GainwardGPUv2Controller::SetBreathingSpeed(unsigned int speed)
-{
-    unsigned char lower = speed & 0xFF;
-    unsigned char upper = (speed >> 2 * 4) & 0xFF;
-
-    bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_BREATHE_SPEED_REGISTER_A, lower);
-    bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_BREATHE_SPEED_SECONDARY_REGISTER_A, lower);
-    bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_BREATHE_SPEED_REGISTER_B, upper);
-    bus->i2c_smbus_write_byte_data(dev, GAINWARD_V2_BREATHE_SPEED_SECONDARY_REGISTER_B, upper);
-}

Controllers/GainwardGPUController/GainwardGPUv2Controller/GainwardGPUv2Controller.h

@@ -1,101 +0,0 @@
-/*---------------------------------------------------------*\
-| GainwardGPUv2Controller.h                                 |
-|                                                           |
-|   Driver for Gainward v2 GPU                              |
-|                                                           |
-|   KundaPanda                                  04 Jan 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#pragma once
-
-#include <string>
-#include "i2c_smbus.h"
-
-typedef unsigned char gainward_gpu_dev_id;
-
-/*---------------------------------------------------------------------------------*\
- | Newer Gainward models seem to use addresses very similar to those used by EVGA   |
- \*-------------------------------------------------------------------------------**/
-
-enum
-{
-    /* RGB Registers */
-    GAINWARD_V2_RED_REGISTER                        = 0x6C, /* Red Register */
-    GAINWARD_V2_GREEN_REGISTER                      = 0x6D, /* Green Register */
-    GAINWARD_V2_BLUE_REGISTER                       = 0x6E, /* Blue Register */
-    GAINWARD_V2_RED_SECONDARY_REGISTER              = 0x70, /* Red Register 2 */
-    GAINWARD_V2_GREEN_SECONDARY_REGISTER            = 0x71, /* Green Register 2 */
-    GAINWARD_V2_BLUE_SECONDARY_REGISTER             = 0x72, /* Blue Register 2 */
-    GAINWARD_V2_RED_TERTIARY_REGISTER               = 0xE4, /* Red Register 3 */
-    GAINWARD_V2_GREEN_TERTIARY_REGISTER             = 0xE5, /* Green Register 3 */
-    GAINWARD_V2_BLUE_TERTIARY_REGISTER              = 0xE6, /* Blue Register 3 */
-    GAINWARD_V2_MODE_REGISTER                       = 0xE0, /* Mode Register */
-    /* Direct mode switch register
-     * 0x1 Software control
-     * 0x22 Breathing */
-    GAINWARD_V2_STATIC_CONTROL_REGISTER             = 0x60,
-    GAINWARD_V2_BREATHE_SPEED_REGISTER_A            = 0x62, /* Lower part of speed control for breathe effect */
-    GAINWARD_V2_BREATHE_SPEED_REGISTER_B            = 0x63, /* Upper part of speed control for breathe effect */
-    GAINWARD_V2_BREATHE_SPEED_SECONDARY_REGISTER_A  = 0x64, /* Lower part of speed control for breathe effect - prob. secondary color */
-    GAINWARD_V2_BREATHE_SPEED_SECONDARY_REGISTER_B  = 0x65, /* Upper part of speed control for breathe effect - prob. secondary color */
-    /* Mode direction Register
-     * 0x0
-     * 0x1 */
-    GAINWARD_V2_MODE_DIRECTION_REGISTER             = 0xE1,
-    /* Mode speed Register
-     * 0x0 MAX
-     * 0xF MIN */
-    GAINWARD_V2_SPEED_REGISTER                      = 0xE2,
-};
-
-enum
-{
-    /* Manual color selection using primary registers */
-    GAINWARD_V2_MODE_STATIC                         = 0x00,
-    /* Rainbow cycling with direction and speed controls */
-    GAINWARD_V2_MODE_CYCLE                          = 0x01,
-    /* One strobing color running around the fan
-     * Color using primary registers, direction and speed control */
-    GAINWARD_V2_MODE_STROBE                         = 0x02,
-};
-
-enum
-{
-    GAINWARD_V2_COLOR_REGISTER_PRIMARY,
-    GAINWARD_V2_COLOR_REGISTER_SECONDARY,
-    GAINWARD_V2_COLOR_REGISTER_TERTIARY,
-};
-
-enum
-{
-    /* Software controlled direct mode */
-    GAINWARD_V2_STATIC_SOFTWARE                     = 0x01,
-    /* GPU controlled direct mode with breathing effect */
-    GAINWARD_V2_STATIC_BREATHING                    = 0x22,
-};
-
-class GainwardGPUv2Controller
-{
-public:
-    GainwardGPUv2Controller(i2c_smbus_interface* bus, gainward_gpu_dev_id, std::string dev_name);
-    ~GainwardGPUv2Controller();
-
-    std::string   GetDeviceLocation();
-    std::string   GetDeviceName();
-
-    unsigned char GetLEDRed();
-    unsigned char GetLEDGreen();
-    unsigned char GetLEDBlue();
-    void          SetLEDColors(unsigned char red, unsigned char green, unsigned char blue, unsigned char color_register = GAINWARD_V2_COLOR_REGISTER_PRIMARY);
-    void          SetMode(unsigned char mode, unsigned char speed, unsigned char direct_mode = GAINWARD_V2_STATIC_SOFTWARE);
-    void          SetBreathingSpeed(unsigned int speed);
-    void          SetDirection(unsigned char direction);
-
-private:
-    i2c_smbus_interface *   bus;
-    gainward_gpu_dev_id     dev;
-    std::string             name;
-};

Controllers/GainwardGPUController/GainwardGPUv2Controller/RGBController_GainwardGPUv2.cpp

@@ -1,187 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_GainwardGPUv2.cpp                           |
-|                                                           |
-|   RGBController for Gainward v2 GPU                       |
-|                                                           |
-|   KundaPanda                                  04 Jan 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include "RGBController_GainwardGPUv2.h"
-
-/**------------------------------------------------------------------*\
-    @name Gainward GPU v2
-    @category GPU
-    @type I2C
-    @save :x:
-    @direct :x:
-    @effects :white_check_mark:
-    @detectors DetectGainwardGPUControllers
-    @comment
-\*-------------------------------------------------------------------*/
-
-RGBController_GainwardGPUv2::RGBController_GainwardGPUv2(GainwardGPUv2Controller* controller_ptr)
-{
-    controller                  = controller_ptr;
-
-    name                        = controller->GetDeviceName();
-    vendor                      = "Gainward";
-    type                        = DEVICE_TYPE_GPU;
-    description                 = "Gainward GPU V2 Device";
-    location                    = controller->GetDeviceLocation();
-
-    mode Static;
-    Static.name                 = "Static";
-    Static.value                = GAINWARD_V2_MODE_STATIC;
-    Static.flags                = MODE_FLAG_HAS_PER_LED_COLOR;
-    Static.color_mode           = MODE_COLORS_PER_LED;
-    modes.push_back(Static);
-
-    mode Breathe;
-    Breathe.name                = "Breathing";
-    Breathe.value               = GAINWARD_V2_MODE_STATIC;
-    Breathe.flags               = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR | MODE_FLAG_HAS_SPEED;
-    Breathe.speed_max           = 0x000a;
-    Breathe.speed_min           = 0x1324;
-    Breathe.color_mode          = MODE_COLORS_MODE_SPECIFIC;
-    Breathe.colors_min          = 2;
-    Breathe.colors_max          = 2;
-    Breathe.colors.resize(2);
-    modes.push_back(Breathe);
-
-    mode RainbowWave;
-    RainbowWave.name            = "Rainbow Wave";
-    RainbowWave.value           = GAINWARD_V2_MODE_CYCLE;
-    RainbowWave.flags           = MODE_FLAG_HAS_SPEED | MODE_FLAG_HAS_DIRECTION_LR;
-    RainbowWave.speed_max       = 0x0;
-    RainbowWave.speed_min       = 0xF;
-    RainbowWave.color_mode      = MODE_COLORS_NONE;
-    modes.push_back(RainbowWave);
-
-    mode Strobe;
-    Strobe.name                 = "Strobe";
-    Strobe.value                = GAINWARD_V2_MODE_STROBE;
-    Strobe.flags                = MODE_FLAG_HAS_SPEED | MODE_FLAG_HAS_DIRECTION_LR | MODE_FLAG_HAS_MODE_SPECIFIC_COLOR;
-    Strobe.color_mode           = MODE_COLORS_MODE_SPECIFIC;
-    Strobe.colors_min           = 1;
-    Strobe.colors_max           = 1;
-    Strobe.colors.resize(1);
-    Strobe.speed_max            = 0x0;
-    Strobe.speed_min            = 0xF;
-    modes.push_back(Strobe);
-
-    SetupZones();
-
-    /*-------------------------*\
-    | Initialize active mode    |
-    \*-------------------------*/
-    active_mode = 0;
-}
-
-RGBController_GainwardGPUv2::~RGBController_GainwardGPUv2()
-{
-    Shutdown();
-
-    delete controller;
-}
-
-void RGBController_GainwardGPUv2::SetupZones()
-{
-    /*---------------------------------------------------------*\
-    | Set up zone                                               |
-    \*---------------------------------------------------------*/
-    zone gainward_gpu_zone;
-    gainward_gpu_zone.name              = "GPU";
-    gainward_gpu_zone.type              = ZONE_TYPE_SINGLE;
-    gainward_gpu_zone.leds_min          = 1;
-    gainward_gpu_zone.leds_max          = 1;
-    gainward_gpu_zone.leds_count        = 1;
-    zones.push_back(gainward_gpu_zone);
-
-    /*---------------------------------------------------------*\
-    | Set up LED                                                |
-    \*---------------------------------------------------------*/
-    led gainward_gpu_led;
-    gainward_gpu_led.name               = "GPU";
-    leds.push_back(gainward_gpu_led);
-
-    SetupColors();
-
-    /*---------------------------------------------------------*\
-    | Initialize color                                          |
-    \*---------------------------------------------------------*/
-    unsigned char red = controller->GetLEDRed();
-    unsigned char grn = controller->GetLEDGreen();
-    unsigned char blu = controller->GetLEDBlue();
-
-    colors[0] =  ToRGBColor(red, grn, blu);
-}
-
-void RGBController_GainwardGPUv2::DeviceUpdateLEDs()
-{
-    for(unsigned int color : colors)
-    {
-        unsigned char red = RGBGetRValue(color);
-        unsigned char grn = RGBGetGValue(color);
-        unsigned char blu = RGBGetBValue(color);
-
-        controller->SetLEDColors(red, grn, blu);
-        controller->SetMode(GAINWARD_V2_MODE_STATIC, 0x2);
-    }
-}
-
-void RGBController_GainwardGPUv2::DeviceUpdateZoneLEDs(int /*zone*/)
-{
-    DeviceUpdateLEDs();
-}
-
-void RGBController_GainwardGPUv2::DeviceUpdateSingleLED(int /*led*/)
-{
-    DeviceUpdateLEDs();
-}
-
-void RGBController_GainwardGPUv2::DeviceUpdateMode()
-{
-    mode current_mode = modes[(unsigned int)active_mode];
-    switch (active_mode)
-    {
-        case 1:
-            {
-                controller->SetBreathingSpeed(current_mode.speed);
-
-                unsigned char r1 = RGBGetRValue(current_mode.colors[0]);
-                unsigned char g1 = RGBGetGValue(current_mode.colors[0]);
-                unsigned char b1 = RGBGetBValue(current_mode.colors[0]);
-                controller->SetLEDColors(r1, g1, b1);
-
-                unsigned char r2 = RGBGetRValue(current_mode.colors[1]);
-                unsigned char g2 = RGBGetGValue(current_mode.colors[1]);
-                unsigned char b2 = RGBGetBValue(current_mode.colors[1]);
-                controller->SetLEDColors(r2, g2, b2, GAINWARD_V2_COLOR_REGISTER_SECONDARY);
-                controller->SetMode(GAINWARD_V2_MODE_STATIC, 0x2, GAINWARD_V2_STATIC_BREATHING);
-            }
-            break;
-
-        /*---------------------------------------------*\
-        | Case 3 intentionally falls through to case 2  |
-        \*---------------------------------------------*/
-        case 3:
-            {
-                unsigned char r = RGBGetRValue(current_mode.colors[0]);
-                unsigned char g = RGBGetGValue(current_mode.colors[0]);
-                unsigned char b = RGBGetBValue(current_mode.colors[0]);
-                controller->SetLEDColors(r, g, b, GAINWARD_V2_COLOR_REGISTER_TERTIARY);
-            }
-
-        case 2:
-            controller->SetMode((unsigned char)(current_mode.value), (unsigned char)(current_mode.speed));
-            controller->SetDirection(current_mode.direction);
-            break;
-
-        default:
-            controller->SetMode((unsigned char)(current_mode.value), (unsigned char)(current_mode.speed));
-            break;
-    }
-}

Controllers/GainwardGPUController/GainwardGPUv2Controller/RGBController_GainwardGPUv2.h

@@ -1,33 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_GainwardGPUv2.h                             |
-|                                                           |
-|   RGBController for Gainward v2 GPU                       |
-|                                                           |
-|   KundaPanda                                  04 Jan 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#pragma once
-
-#include "RGBController.h"
-#include "GainwardGPUv2Controller.h"
-
-class RGBController_GainwardGPUv2 : public RGBController
-{
-public:
-    RGBController_GainwardGPUv2(GainwardGPUv2Controller* controller_ptr);
-    ~RGBController_GainwardGPUv2();
-
-    void        SetupZones();
-
-    void        DeviceUpdateLEDs();
-    void        DeviceUpdateZoneLEDs(int zone);
-    void        DeviceUpdateSingleLED(int led);
-
-    void        DeviceUpdateMode();
-
-private:
-    GainwardGPUv2Controller* controller;
-};

Controllers/GigabyteRGBFusion2BlackwellGPUController/GigabyteRGBFusion2BlackwellGPUControllerDetect.cpp

@@ -1,4 +1,4 @@
-/*---------------------------------------------------------*\
+/*---------------------------------------------------------*\
 | GigabyteRGBFusion2BlackwellGPUControllerDetect.cpp        |
 |                                                           |
 |   Detector for Gigabyte RGB Fusion 2 Blackwell GPU        |
@@ -130,8 +130,8 @@ REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS GeForce RTX 5080 XTREME WATERFORCE",
 REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 5080 XTREME WATERFORCE",            DetectGigabyteRGBFusion2BlackwellWaterforceLayoutGPUControllers,                NVIDIA_VEN,     NVIDIA_RTX5080_DEV,         GIGABYTE_SUB_VEN, GIGABYTE_RTX5080_XTREME_WATERFORCE_16G_SUB_DEV,           0x75);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS GeForce RTX 5080 MASTER ICE",             DetectGigabyteRGBFusion2BlackwellAorusMaster5080LayoutGPUControllers,           NVIDIA_VEN,     NVIDIA_RTX5080_DEV,         GIGABYTE_SUB_VEN, GIGABYTE_AORUS_RTX5080_MASTER_ICE_16G_SUB_DEV,            0x75);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 5090 Gaming OC",                    DetectGigabyteRGBFusion2BlackwellGamingLayoutGPUControllers,                    NVIDIA_VEN,     NVIDIA_RTX5090_DEV,         GIGABYTE_SUB_VEN, GIGABYTE_RTX5090_GAMING_OC_32G_SUB_DEV,                   0x75);
-REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 5090 XTREME WATERFORCE",            DetectGigabyteRGBFusion2BlackwellWaterforceLayoutGPUControllers,                NVIDIA_VEN,     NVIDIA_RTX5090_DEV,         GIGABYTE_SUB_VEN, GIGABYTE_RTX5090_XTREME_WATERFORCE_32G_SUB_DEV1,          0x75);
-REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 5090 XTREME WATERFORCE",            DetectGigabyteRGBFusion2BlackwellWaterforceLayoutGPUControllers,                NVIDIA_VEN,     NVIDIA_RTX5090_DEV,         GIGABYTE_SUB_VEN, GIGABYTE_RTX5090_XTREME_WATERFORCE_32G_SUB_DEV2,          0x75);
+REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 5090 XTREME WATERFORCE",            DetectGigabyteRGBFusion2BlackwellGamingLayoutGPUControllers,                    NVIDIA_VEN,     NVIDIA_RTX5090_DEV,         GIGABYTE_SUB_VEN, GIGABYTE_RTX5090_XTREME_WATERFORCE_32G_SUB_DEV,           0x75);
+REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 5090 XTREME WATERFORCE WB",         DetectGigabyteRGBFusion2BlackwellWaterforceLayoutGPUControllers,                NVIDIA_VEN,     NVIDIA_RTX5090_DEV,         GIGABYTE_SUB_VEN, GIGABYTE_RTX5090_XTREME_WATERFORCE_WB_32G_SUB_DEV,        0x75);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS GeForce RTX 5090 MASTER",                 DetectGigabyteRGBFusion2BlackwellGamingLayoutGPUControllers,                    NVIDIA_VEN,     NVIDIA_RTX5090_DEV,         GIGABYTE_SUB_VEN, GIGABYTE_AORUS_RTX5090_MASTER_32G_SUB_DEV,                0x75);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS GeForce RTX 5090 MASTER ICE",             DetectGigabyteRGBFusion2BlackwellGamingLayoutGPUControllers,                    NVIDIA_VEN,     NVIDIA_RTX5090_DEV,         GIGABYTE_SUB_VEN, GIGABYTE_AORUS_RTX5090_MASTER_ICE_32G_SUB_DEV,            0x75);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS GeForce RTX 5090 D V2 MASTER ICE",        DetectGigabyteRGBFusion2BlackwellAorusMaster5090DV2IceLayoutGPUControllers,     NVIDIA_VEN,     NVIDIA_RTX5090D_V2_DEV,     GIGABYTE_SUB_VEN, GIGABYTE_AORUS_RTX5090D_V2_MASTER_ICE_24G_SUB_DEV,        0x75);
@@ -139,6 +139,7 @@ REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS GeForce RTX 5090 D V2 MASTER ICE",
 /*---------------------------------------------------------*\
 |  AMD GPUs                                                 |
 \*---------------------------------------------------------*/
+REGISTER_I2C_PCI_DETECTOR("Gigabyte Radeon RX 9060 GAMING OC 8G",                   DetectGigabyteRGBFusion2BlackwellGamingLayoutGPUControllers,                    AMD_GPU_VEN,    AMD_NAVI44_DEV,             GIGABYTE_SUB_VEN, GIGABYTE_RX9060XT_GAMING_OC_8G_SUB_DEV,                   0x75);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte Radeon RX 9060 XT GAMING",                      DetectGigabyteRGBFusion2BlackwellGamingLayoutGPUControllers,                    AMD_GPU_VEN,    AMD_NAVI44_DEV,             GIGABYTE_SUB_VEN, GIGABYTE_RX9060XT_GAMING_16G_SUB_DEV,                     0x75);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte Radeon RX 9060 XT GAMING OC",                   DetectGigabyteRGBFusion2BlackwellGamingLayoutGPUControllers,                    AMD_GPU_VEN,    AMD_NAVI44_DEV,             GIGABYTE_SUB_VEN, GIGABYTE_RX9060XT_GAMING_OC_16G_SUB_DEV,                  0x75);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS Radeon RX 9070 XT Elite",                 DetectGigabyteRGBFusion2BlackwellGamingLayoutGPUControllers,                    AMD_GPU_VEN,    AMD_NAVI48_DEV,             GIGABYTE_SUB_VEN, GIGABYTE_AORUS_RX9070XT_ELITE_16G_SUB_DEV,                0x75);

Controllers/GigabyteRGBFusion2GPUController/GigabyteRGBFusion2GPUControllerDetect.cpp

@@ -52,8 +52,12 @@ bool TestForGigabyteRGBFusion2GPUController(i2c_smbus_interface* bus, unsigned c
     //Note that GeForce RTX 4080 Gigabyte AORUS MASTER 16G exposes two i2c bus with writable address 0x71 but one respond
     //0x00 0x00 0x00 0x00 so it should be the one controlling the LCD screen. So we skip this bus
 
-    //All seen responses start with 0xAB, so we check for this.
-    if(res < 0 || data_readpkt[0] != 0xAB)
+    //All seen responses start with 0xAB, so we check for this. A DDC/EDID
+    //style bus can echo the written command byte back for every read, so an
+    //all-0xAB response is a mirror, not a controller; every real controller
+    //seen so far follows 0xAB with version bytes (see table above).
+    if(res < 0 || data_readpkt[0] != 0xAB ||
+       (data_readpkt[1] == 0xAB && data_readpkt[2] == 0xAB && data_readpkt[3] == 0xAB))
     {
         // Assemble C-string with respons for debugging
         std::string text = "";
@@ -140,7 +144,8 @@ REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 4070 GAMING OC",
 REGISTER_I2C_PCI_DETECTOR("Gigabyte Geforce RTX 4070 Aero OC",                         DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX4070_DEV,         GIGABYTE_SUB_VEN,   GIGABYTE_RTX4070_AERO_OC_12G_SUB_DEV,           0x71);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 4070 SUPER GAMING OC",                 DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX4070S_DEV,        GIGABYTE_SUB_VEN,   GIGABYTE_RTX4070S_GAMING_OC_12G,                0x71);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 4070 SUPER Aero OC",                   DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX4070S_DEV,        GIGABYTE_SUB_VEN,   GIGABYTE_RTX4070S_AERO_OC_12G,                  0x71);
-REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 4070 SUPER Eagle OC",                  DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX4070S_DEV,        GIGABYTE_SUB_VEN,   GIGABYTE_RTX4070S_EAGLE_OC_ICE_12G,             0x71);
+REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 4070 SUPER Eagle OC",                  DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX4070S_DEV,        GIGABYTE_SUB_VEN,   GIGABYTE_RTX4070S_EAGLE_OC_12G,                 0x71);
+REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 4070 SUPER Eagle OC ICE",              DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX4070S_DEV,        GIGABYTE_SUB_VEN,   GIGABYTE_RTX4070S_EAGLE_OC_ICE_12G,             0x71);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 4070 Ti GAMING",                       DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX4070TI_DEV,       GIGABYTE_SUB_VEN,   GIGABYTE_RTX4070TI_GAMING_12G,                  0x71);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 4070 Ti GAMING OC",                    DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX4070TI_DEV,       GIGABYTE_SUB_VEN,   GIGABYTE_RTX4070TI_GAMING_OC_12G,               0x71);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 4070 Ti GAMING OC",                    DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX4070TI_DEV,       GIGABYTE_SUB_VEN,   GIGABYTE_RTX4070TI_GAMING_OC_12G_SUB_DEV2,      0x71);
@@ -162,6 +167,7 @@ REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 4090 GAMING OC",
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS GeForce RTX 4090 MASTER",                    DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX4090_DEV,         GIGABYTE_SUB_VEN,   GIGABYTE_AORUS_RTX4090_MASTER_24G_SUB_DEV,      0x71);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS GeForce RTX 5090 D MASTER",                  DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX5090D_DEV,        GIGABYTE_SUB_VEN,   GIGABYTE_AORUS_RTX5090D_MASTER_32G_SUB_DEV,     0x71);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 5080 GAMING OC",                       DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX5080_DEV,         GIGABYTE_SUB_VEN,   GIGABYTE_RTX5080_GAMING_OC_16G_SUB_DEV,         0x71);
+REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS GeForce RTX 5080 MASTER ICE",                DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX5080_DEV,         GIGABYTE_SUB_VEN,   GIGABYTE_AORUS_RTX5080_MASTER_ICE_16G_SUB_DEV,  0x71);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte GeForce RTX 5090 GAMING OC",                       DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX5090D_DEV,        GIGABYTE_SUB_VEN,   GIGABYTE_RTX5090_GAMING_OC_32G_SUB_DEV,         0x71);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS GeForce RTX 5090 MASTER",                    DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX5090_DEV,         GIGABYTE_SUB_VEN,   GIGABYTE_AORUS_RTX5090_MASTER_32G_SUB_DEV,      0x71);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS GeForce RTX 5090 MASTER ICE",                DetectGigabyteRGBFusion2GPUControllers, NVIDIA_VEN, NVIDIA_RTX5090_DEV,         GIGABYTE_SUB_VEN,   GIGABYTE_AORUS_RTX5090_MASTER_ICE_32G_SUB_DEV,  0x71);
@@ -185,6 +191,7 @@ REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS Radeon RX 7900 XTX ELITE 24G",
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS RX 6750 XT ELITE 12G",                       DetectGigabyteRGBFusion2GPUControllers, AMD_GPU_VEN, AMD_NAVI22_DEV,            GIGABYTE_SUB_VEN,   GIGABYTE_AORUS_RX_6750_XT_ELITE_12G_SUB_DEV,    0x70);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS RX 6900 XT MASTER rev 2.0",                  DetectGigabyteRGBFusion2GPUControllers, AMD_GPU_VEN, AMD_NAVI21_DEV2,           GIGABYTE_SUB_VEN,   GIGABYTE_AORUS_RX6900XT_MASTER_SUB_DEV,         0x70);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS RX 6900 XT EXTREME WATERFORCE WB",           DetectGigabyteRGBFusion2GPUControllers, AMD_GPU_VEN, AMD_NAVI21_DEV2,           GIGABYTE_SUB_VEN,   GIGABYTE_RX6900XT_XTREME_WATERFORCE_WB_SUB_DEV, 0x70);
+REGISTER_I2C_PCI_DETECTOR("Gigabyte Radeon RX 9060 XT GAMING OC 8G",                   DetectGigabyteRGBFusion2GPUControllers, AMD_GPU_VEN, AMD_NAVI44_DEV,            GIGABYTE_SUB_VEN,   GIGABYTE_RX9060XT_GAMING_OC_8G_SUB_DEV,         0x73);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte AORUS Radeon RX 9070 XT Elite",                    DetectGigabyteRGBFusion2GPUControllers, AMD_GPU_VEN, AMD_NAVI48_DEV,            GIGABYTE_SUB_VEN,   GIGABYTE_AORUS_RX9070XT_ELITE_16G_SUB_DEV,      0x73);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte Radeon RX 9070 XT GAMING OC",                      DetectGigabyteRGBFusion2GPUControllers, AMD_GPU_VEN, AMD_NAVI48_DEV,            GIGABYTE_SUB_VEN,   GIGABYTE_RX9070XT_GAMING_OC_16G_SUB_DEV,        0x73);
 REGISTER_I2C_PCI_DETECTOR("Gigabyte Radeon RX 9070 XT GAMING OC ICE",                  DetectGigabyteRGBFusion2GPUControllers, AMD_GPU_VEN, AMD_NAVI48_DEV,            GIGABYTE_SUB_VEN,   GIGABYTE_RX9070XT_GAMING_OC_ICE_16G_SUB_DEV,    0x73);

Controllers/GigabyteRGBFusion2USBController/GigabyteFusion2USB_Devices.cpp

@@ -4,8 +4,8 @@
 |   Gigabyte Fusion 2 USB Device layouts and                |
 |     and mapping to the device IDs stored on chip          |
 |                                                           |
-|   megadjc                                     31 Jul 2025 |
 |   chrism                                      29 Aug 2025 |
+|   megadjc                                     03 Sep 2026 |
 |                                                           |
 |   This file is part of the OpenRGB project                |
 |   SPDX-License-Identifier: GPL-2.0-only                   |
@@ -19,16 +19,16 @@
 static const gb_fusion2_zone common_d_led_zone =
 {
     HDR_D_LED1,
-    0,
-    1024,
+    RGBFUSION2_DLED_LEDS_MIN,
+    RGBFUSION2_DLED_LEDS_MAX,
     "D_LED"
 };
 
 static const gb_fusion2_zone common_gc_usb_d_led_zone =
 {
     LED1,
-    0,
-    1024,
+    RGBFUSION2_DLED_LEDS_MIN,
+    RGBFUSION2_DLED_LEDS_MAX,
     "D_LED"
 };
 
@@ -36,48 +36,48 @@ static const gb_fusion2_zone common_gc_usb_d_led_zone =
 static const gb_fusion2_zone common_d_led1_zone =
 {
     HDR_D_LED1,
-    0,
-    1024,
+    RGBFUSION2_DLED_LEDS_MIN,
+    RGBFUSION2_DLED_LEDS_MAX,
     "D_LED1"
 };
 
 static const gb_fusion2_zone common_dled1_dled2_zone =
 {
     HDR_D_LED1,
-    0,
-    1024,
+    RGBFUSION2_DLED_LEDS_MIN,
+    RGBFUSION2_DLED_LEDS_MAX,
     "D_LED1/D_LED2"
 };
 
 static const gb_fusion2_zone common_argb_v2_1_zone =
 {
     HDR_D_LED1,
-    0,
-    1024,
+    RGBFUSION2_57XX_LEDS_MIN,
+    RGBFUSION2_57XX_LEDS_MAX,
     "ARGB_V2_1"
 };
 
 static const gb_fusion2_zone alt_argb_v2_1_zone =
 {
     LED3,
-    0,
-    1024,
+    RGBFUSION2_57XX_LEDS_MIN,
+    RGBFUSION2_57XX_LEDS_MAX,
     "ARGB_V2_1"
 };
 
 static const gb_fusion2_zone common_argb_v2_1_3_zone =
 {
     HDR_D_LED1,
-    0,
-    1024,
+    RGBFUSION2_57XX_LEDS_MIN,
+    RGBFUSION2_57XX_LEDS_MAX,
     "ARGB_V2_1/ARGB_V2_3"
 };
 
 static const gb_fusion2_zone common_d_led2_zone =
 {
     HDR_D_LED2,
-    0,
-    1024,
+    RGBFUSION2_DLED_LEDS_MIN,
+    RGBFUSION2_DLED_LEDS_MAX,
     "D_LED2"
 };
 
@@ -85,47 +85,47 @@ static const gb_fusion2_zone common_d_led2_aux_zone =
 {
     HDR_D_LED2,
     2,
-    1024,
+    RGBFUSION2_DLED_LEDS_MAX,
     "D_LED2 + Aux"
 };
 
 static const gb_fusion2_zone common_argb_v2_2_zone =
 {
     HDR_D_LED2,
-    0,
-    1024,
+    RGBFUSION2_57XX_LEDS_MIN,
+    RGBFUSION2_57XX_LEDS_MAX,
     "ARGB_V2_2"
 };
 
 static const gb_fusion2_zone alt_argb_v2_2_zone =
 {
     LED4,
-    0,
-    1024,
+    RGBFUSION2_57XX_LEDS_MIN,
+    RGBFUSION2_57XX_LEDS_MAX,
     "ARGB_V2_2"
 };
 
 static const gb_fusion2_zone common_argb_v2_3_1_zone =
 {
     HDR_D_LED1,
-    0,
-    1024,
+    RGBFUSION2_57XX_LEDS_MIN,
+    RGBFUSION2_57XX_LEDS_MAX,
     "ARGB_V2_3"
 };
 
 static const gb_fusion2_zone common_argb_v2_3_zone =
 {
     HDR_D_LED3,
-    0,
-    1024,
+    RGBFUSION2_57XX_LEDS_MIN,
+    RGBFUSION2_57XX_LEDS_MAX,
     "ARGB_V2_3"
 };
 
 static const gb_fusion2_zone common_argb_v2_4_zone =
 {
     HDR_D_LED4,
-    0,
-    1024,
+    RGBFUSION2_57XX_LEDS_MIN,
+    RGBFUSION2_57XX_LEDS_MAX,
     "ARGB_V2_4"
 };
 

Controllers/GigabyteRGBFusion2USBController/GigabyteFusion2USB_Devices.h

@@ -4,8 +4,8 @@
 |   Gigabyte Fusion 2 USB Device layouts and                |
 |     and mapping to the device IDs stored on chip          |
 |                                                           |
-|   megadjc                                     31 Jul 2025 |
 |   chrism                                      29 Aug 2025 |
+|   megadjc                                     03 Sep 2026 |
 |                                                           |
 |   This file is part of the OpenRGB project                |
 |   SPDX-License-Identifier: GPL-2.0-only                   |
@@ -54,6 +54,8 @@ enum GB_FUSION2_LED_IDX
     HDR_D_LED4          = 8,
     HDR_D_LED3_ARGB     = 0x62,
     HDR_D_LED4_ARGB     = 0x63,
+    ONBOARD1_ARGB       = 0x64,
+    ONBOARD2_ARGB       = 0x65,
 };
 
 /*-------------------------------------------------*\

Controllers/GigabyteRGBFusion2USBController/GigabyteRGBFusion2USBController.cpp

@@ -4,7 +4,7 @@
 |   Driver for Gigabyte Aorus RGB Fusion 2 USB motherboard  |
 |                                                           |
 |   jackun                                      08 Jan 2020 |
-|   megadjc                                     31 Jul 2025 |
+|   megadjc                                     03 Sep 2026 |
 |                                                           |
 |   This file is part of the OpenRGB project                |
 |   SPDX-License-Identifier: GPL-2.0-or-later               |
@@ -55,6 +55,27 @@ static LEDCount LedCountToEnum(unsigned int c)
     }
 }
 
+static LEDCount LedCountFromEnum(uint8_t count){
+    switch(count & 0x0F)
+    {
+        case LEDS_32:
+            return LEDS_32;
+
+        case LEDS_64:
+            return LEDS_64;
+
+        case LEDS_256:
+            return LEDS_256;
+
+        case LEDS_512:
+            return LEDS_512;
+
+        case LEDS_1024:
+        default:
+            return LEDS_1024;
+    }
+}
+
 RGBFusion2USBController::RGBFusion2USBController(hid_device* handle, const char* path, std::string mb_name, uint16_t pid): dev(handle), product_id(pid)
 {
     name        = mb_name;
@@ -96,9 +117,12 @@ bool RGBFusion2USBController::RefreshHardwareInfo()
     }
 
     std::memcpy(&report, buffer, sizeof(IT8297Report));
+
     report_loaded   = true;
     device_num      = report.device_num;
+    fw_id           = report.fw_ver >> 24;
     description     = std::string(report.str_product, 28);
+
     if(std::string::iterator nul = std::find(description.begin(), description.end(), '\0');
        nul != description.end())
     {
@@ -122,10 +146,12 @@ bool RGBFusion2USBController::RefreshHardwareInfo()
         chip_id = text;
     }
 
-    D_LED1_count = LedCountToEnum(report.curr_led_count_low  & 0x0F);
-    D_LED2_count = LedCountToEnum((report.curr_led_count_low  >> 4) & 0x0F);
-    D_LED3_count = LedCountToEnum(report.curr_led_count_high & 0x0F);
-    D_LED4_count = LedCountToEnum((report.curr_led_count_high >> 4) & 0x0F);
+    ARGB_count[0] = LedCountFromEnum(report.argb01_count & 0x0F);
+    ARGB_count[1] = LedCountFromEnum((report.argb01_count >> 4) & 0x0F);
+    ARGB_count[2] = LedCountFromEnum(report.argb23_count & 0x0F);
+    ARGB_count[3] = LedCountFromEnum((report.argb23_count >> 4) & 0x0F);
+    ARGB_count[4] = LedCountFromEnum(report.argb45_count & 0x0F);
+    ARGB_count[5] = LedCountFromEnum((report.argb45_count >> 4) & 0x0F);
 
     cal_data.dled[0]   = report.cal_strip0;
     cal_data.dled[1]   = report.cal_strip1;
@@ -150,15 +176,15 @@ bool RGBFusion2USBController::RefreshHardwareInfo()
 
             cal_data.dled[2] = cali.cal_strip2;
             cal_data.dled[3] = cali.cal_strip3;
-            cal_data.spare[2] = cali.cal_spare2;
-            cal_data.spare[3] = cali.cal_spare3;
+            cal_data.dled[4] = cali.cal_strip4;
+            cal_data.dled[5] = cali.cal_strip5;
         }
         else
         {
             cal_data.dled[2] = 0;
             cal_data.dled[3] = 0;
-            cal_data.spare[2] = 0;
-            cal_data.spare[3] = 0;
+            cal_data.dled[4] = 0;
+            cal_data.dled[5] = 0;
             cali_loaded      = false;
         }
     }
@@ -166,8 +192,8 @@ bool RGBFusion2USBController::RefreshHardwareInfo()
     {
         cal_data.dled[2] = 0;
         cal_data.dled[3] = 0;
-        cal_data.spare[2] = 0;
-        cal_data.spare[3] = 0;
+        cal_data.dled[4] = 0;
+        cal_data.dled[5] = 0;
     }
 
     return report_loaded;
@@ -184,11 +210,13 @@ std::string RGBFusion2USBController::DecodeCalibrationBuffer(uint32_t value) con
     uint8_t bo_b        =  value        & 0xFF;
     uint8_t bo_g        = (value >> 8 ) & 0xFF;
     uint8_t bo_r        = (value >> 16) & 0xFF;
+    uint8_t bo_reserved = (value >> 24) & 0xFF;
 
+    bool reserved_clear = (bo_reserved == 0);
     bool in_range       = (bo_r < 3 && bo_g < 3 && bo_b < 3);
     bool distinct       = (bo_r != bo_g && bo_r != bo_b && bo_g != bo_b);
 
-    if(in_range && distinct)
+    if(reserved_clear && in_range && distinct)
     {
         out[bo_r] = 'R';
         out[bo_g] = 'G';
@@ -196,7 +224,7 @@ std::string RGBFusion2USBController::DecodeCalibrationBuffer(uint32_t value) con
         return out;
     }
 
-    return "BAD";
+    return "INVALID";
 }
 
 uint32_t RGBFusion2USBController::EncodeCalibrationBuffer(const std::string& rgb_order)
@@ -247,18 +275,32 @@ EncodedCalibration RGBFusion2USBController::GetCalibration(bool refresh_from_hw)
     out.mainboard = DecodeCalibrationBuffer(cal_data.mainboard);
 
     if(product_id == 0x5711)
+    {
+        if(cali_loaded)
         {
             out.dled[2] = DecodeCalibrationBuffer(cal_data.dled[2]);
             out.dled[3] = DecodeCalibrationBuffer(cal_data.dled[3]);
-        out.spare[2] = DecodeCalibrationBuffer(cal_data.spare[2]);
-        out.spare[3] = DecodeCalibrationBuffer(cal_data.spare[3]);
+            out.dled[4] = DecodeCalibrationBuffer(cal_data.dled[4]);
+            out.dled[5] = DecodeCalibrationBuffer(cal_data.dled[5]);
+        }
+        else
+        {
+            /*-------------------------------------------------*\
+            | CC61 was not available, so these values are       |
+            | unknown rather than OFF.                           |
+            \*-------------------------------------------------*/
+            out.dled[2] = "INVALID";
+            out.dled[3] = "INVALID";
+            out.dled[4] = "INVALID";
+            out.dled[5] = "INVALID";
+        }
     }
     else
     {
         out.dled[2] = "OFF";
         out.dled[3] = "OFF";
-        out.spare[2] = "OFF";
-        out.spare[3] = "OFF";
+        out.dled[4] = "OFF";
+        out.dled[5] = "OFF";
     }
 
     return out;
@@ -271,34 +313,72 @@ bool RGBFusion2USBController::SetCalibration(const EncodedCalibration& cal, bool
         return false;
     }
 
-    if(EncodeCalibrationBuffer(cal.dled[0])       == cal_data.dled[0]
-        && EncodeCalibrationBuffer(cal.dled[1])   == cal_data.dled[1]
-        && EncodeCalibrationBuffer(cal.mainboard) == cal_data.mainboard
-        && EncodeCalibrationBuffer(cal.spare[0])  == cal_data.spare[0]
-        && EncodeCalibrationBuffer(cal.spare[1])  == cal_data.spare[1]
-        && (product_id != 0x5711
-        || (EncodeCalibrationBuffer(cal.dled[2])  == cal_data.dled[2]
-        && EncodeCalibrationBuffer(cal.dled[3])   == cal_data.dled[3]
-        && EncodeCalibrationBuffer(cal.spare[2])  == cal_data.spare[2]
-        && EncodeCalibrationBuffer(cal.spare[3])  == cal_data.spare[3])))
+    /*---------------------------------------------------------*\
+    | A calibration write contains the complete calibration     |
+    | payload. Do not write from incomplete hardware state.     |
+    \*---------------------------------------------------------*/
+    if(!report_loaded || (product_id == 0x5711 && !cali_loaded))
     {
-        return true;
+        return false;
     }
 
+    /*---------------------------------------------------------*\
+    | Preserve malformed/unavailable values rather than         |
+    | converting them to zero. Unknown strings are treated the  |
+    | same way so stale configuration cannot erase calibration. |
+    \*---------------------------------------------------------*/
+    auto encode_or_preserve = [&](const std::string& rgb_order, uint32_t current) -> uint32_t
+    {
+        std::string key = rgb_order;
+        std::transform(key.begin(), key.end(), key.begin(),
+                       [](unsigned char c){ return char(std::toupper(c)); });
+
+        if(key == "INVALID" || key == "BAD" || key.empty())
+        {
+            return current;
+        }
+
+        if(key == "OFF" || key == "0")
+        {
+            return 0u;
+        }
+
+        if(GigabyteCalibrationsLookup.find(key) == GigabyteCalibrationsLookup.end())
+        {
+            return current;
+        }
+
+        return EncodeCalibrationBuffer(key);
+    };
+
     CMD_0x33 desired;
 
-    desired.c.d_strip_c0        = EncodeCalibrationBuffer(cal.dled[0]);
-    desired.c.d_strip_c1        = EncodeCalibrationBuffer(cal.dled[1]);
-    desired.c.rgb_cali          = EncodeCalibrationBuffer(cal.mainboard);
-    desired.c.c_spare0          = EncodeCalibrationBuffer(cal.spare[0]);
-    desired.c.c_spare1          = EncodeCalibrationBuffer(cal.spare[1]);
+    desired.c.d_strip_c0 = encode_or_preserve(cal.dled[0], cal_data.dled[0]);
+    desired.c.d_strip_c1 = encode_or_preserve(cal.dled[1], cal_data.dled[1]);
+    desired.c.rgb_cali   = encode_or_preserve(cal.mainboard, cal_data.mainboard);
+    desired.c.c_spare0   = encode_or_preserve(cal.spare[0], cal_data.spare[0]);
+    desired.c.c_spare1   = encode_or_preserve(cal.spare[1], cal_data.spare[1]);
 
     if(product_id == 0x5711)
     {
-        desired.c.d_strip_c2    = EncodeCalibrationBuffer(cal.dled[2]);
-        desired.c.d_strip_c3    = EncodeCalibrationBuffer(cal.dled[3]);
-        desired.c.c_spare2      = EncodeCalibrationBuffer(cal.spare[2]);
-        desired.c.c_spare3      = EncodeCalibrationBuffer(cal.spare[3]);
+        desired.c.d_strip_c2 = encode_or_preserve(cal.dled[2], cal_data.dled[2]);
+        desired.c.d_strip_c3 = encode_or_preserve(cal.dled[3], cal_data.dled[3]);
+        desired.c.d_strip_c4 = encode_or_preserve(cal.dled[4], cal_data.dled[4]);
+        desired.c.d_strip_c5 = encode_or_preserve(cal.dled[5], cal_data.dled[5]);
+    }
+
+    if(desired.c.d_strip_c0 == cal_data.dled[0]
+        && desired.c.d_strip_c1 == cal_data.dled[1]
+        && desired.c.rgb_cali   == cal_data.mainboard
+        && desired.c.c_spare0   == cal_data.spare[0]
+        && desired.c.c_spare1   == cal_data.spare[1]
+        && (product_id != 0x5711
+        || (desired.c.d_strip_c2 == cal_data.dled[2]
+        && desired.c.d_strip_c3  == cal_data.dled[3]
+        && desired.c.d_strip_c4  == cal_data.dled[4]
+        && desired.c.d_strip_c5  == cal_data.dled[5])))
+    {
+        return true;
     }
 
     int rc = SendPacket(desired.buffer);
@@ -309,7 +389,7 @@ bool RGBFusion2USBController::SetCalibration(const EncodedCalibration& cal, bool
 
     ResetController();
     std::this_thread::sleep_for(std::chrono::milliseconds(20));
-    SaveCalState();
+    SaveLightingStateToFlash();
     std::this_thread::sleep_for(std::chrono::milliseconds(20));
 
     cal_data.dled[0]   = desired.c.d_strip_c0;
@@ -322,38 +402,68 @@ bool RGBFusion2USBController::SetCalibration(const EncodedCalibration& cal, bool
     {
         cal_data.dled[2] = desired.c.d_strip_c2;
         cal_data.dled[3] = desired.c.d_strip_c3;
-        cal_data.spare[2] = desired.c.c_spare2;
-        cal_data.spare[3] = desired.c.c_spare3;
+        cal_data.dled[4] = desired.c.d_strip_c4;
+        cal_data.dled[5] = desired.c.d_strip_c5;
     }
     else
     {
         cal_data.dled[2] = 0u;
         cal_data.dled[3] = 0u;
-        cal_data.spare[2] = 0u;
-        cal_data.spare[3] = 0u;
+        cal_data.dled[4] = 0u;
+        cal_data.dled[5] = 0u;
     }
 
     return true;
 }
 
-void RGBFusion2USBController::SetLedCount(unsigned int c0, unsigned int c1, unsigned int c2, unsigned int c3)
+void RGBFusion2USBController::SetLedCount(
+    unsigned int c0,
+    unsigned int c1,
+    unsigned int c2,
+    unsigned int c3,
+    unsigned int c4,
+    unsigned int c5)
 {
-    LEDCount new_d1 = LedCountToEnum(c0);
-    LEDCount new_d2 = LedCountToEnum(c1);
-    LEDCount new_d3 = LedCountToEnum(c2);
-    LEDCount new_d4 = LedCountToEnum(c3);
+    LEDCount new_count[6] =
+    {
+        LedCountToEnum(c0),
+        LedCountToEnum(c1),
+        LedCountToEnum(c2),
+        LedCountToEnum(c3),
+        LedCountToEnum(c4),
+        LedCountToEnum(c5)
+    };
 
-    if(new_d1 == D_LED1_count && new_d2 == D_LED2_count && new_d3 == D_LED3_count && new_d4 == D_LED4_count)
+    bool changed = false;
+
+    for(unsigned int i = 0; i < 6; i++)
+    {
+        if(new_count[i] != ARGB_count[i])
+        {
+            changed = true;
+            break;
+        }
+    }
+
+    if(!changed)
     {
         return;
     }
 
-    D_LED1_count    = new_d1;
-    D_LED2_count    = new_d2;
-    D_LED3_count    = new_d3;
-    D_LED4_count    = new_d4;
+    for(unsigned int i = 0; i < 6; i++)
+    {
+        ARGB_count[i] = new_count[i];
+    }
 
-    SendCCReport(0x34, (new_d2 << 4) | new_d1, (new_d4 << 4) | new_d3);
+    unsigned char buffer[FUSION2_USB_BUFFER_SIZE] = {0};
+
+    buffer[0] = report_id;
+    buffer[1] = 0x34;
+    buffer[2] = (new_count[1] << 4) | new_count[0];
+    buffer[3] = (new_count[3] << 4) | new_count[2];
+    buffer[4] = (new_count[5] << 4) | new_count[4];
+
+    SendPacket(buffer);
 }
 
 /*---------------------------------------------------------*\
@@ -371,7 +481,7 @@ bool RGBFusion2USBController::SetStripBuiltinEffectState(int hdr, bool enable)
                 bitmask = 0x01;
                 break;
             case 0x5711:
-                bitmask = 0x01 | 0x02 | 0x08 | 0x10;
+                bitmask = 0x01 | 0x02 | 0x08 | 0x10 | 0x20 | 0x40;
                 break;
             default:
                 bitmask = 0x01 | 0x02;
@@ -395,6 +505,14 @@ bool RGBFusion2USBController::SetStripBuiltinEffectState(int hdr, bool enable)
             case HDR_D_LED4_ARGB:
                 bitmask = 0x10;
                 break;
+             case LED10:
+            case ONBOARD1_ARGB:
+                bitmask = 0x20;
+                break;
+            case LED11:
+            case ONBOARD2_ARGB:
+                bitmask = 0x40;
+                break;
             default:
                 bitmask = 0x01;
                 break;
@@ -416,17 +534,17 @@ bool RGBFusion2USBController::SetStripBuiltinEffectState(int hdr, bool enable)
 }
 
 /*---------------------------------------------------------*\
-| Persist LED config data                                   |
+| Enable LED Lighting Persistence                           |
 \*---------------------------------------------------------*/
-bool RGBFusion2USBController::SaveLEDState(bool e)
+bool RGBFusion2USBController::SetPersistentLightingEnabled(bool e)
 {
     return SendCCReport(0x47, e ? 1 : 0);
 }
 
 /*---------------------------------------------------------*\
-| Persist calibration                                       |
+| Save lighting state to flash                              |
 \*---------------------------------------------------------*/
-bool RGBFusion2USBController::SaveCalState()
+bool RGBFusion2USBController::SaveLightingStateToFlash()
 {
     return SendCCReport(0x5E, 0);
 }
@@ -440,7 +558,7 @@ bool RGBFusion2USBController::EnableBeat(bool e)
 }
 
 /*---------------------------------------------------------*\
-| Set Lamp Array mode (MSDL)                                |
+| Set Lamp Array mode                                       |
 \*---------------------------------------------------------*/
 bool RGBFusion2USBController::EnableLampArray(bool enable)
 {
@@ -461,6 +579,16 @@ std::string RGBFusion2USBController::GetDeviceDescription()
     return(description);
 }
 
+uint8_t RGBFusion2USBController::GetFWID()
+{
+    return(fw_id);
+}
+
+uint8_t RGBFusion2USBController::GetFWRevision()
+{
+    return((report.fw_ver >> 16) & 0xFF);
+}
+
 std::string RGBFusion2USBController::GetFWVersion()
 {
     return(version);
@@ -512,6 +640,12 @@ void RGBFusion2USBController::SetStripColors(unsigned int hdr, RGBColor* colors,
         case HDR_D_LED4_ARGB:
             byteorder = cal_data.dled[3];
             break;
+        case ONBOARD1_ARGB:
+            byteorder = cal_data.dled[4];
+            break;
+        case ONBOARD2_ARGB:
+            byteorder = cal_data.dled[5];
+            break;
         default:
             byteorder = cal_data.dled[0];
             break;
@@ -618,7 +752,7 @@ void RGBFusion2USBController::SetLEDEffect(int led, int mode, unsigned int speed
             pkt.e.effect_param0     = 7;
             break;
         case EFFECT_WAVE:
-            pkt.e.period0           = (((speed + 1)^2) + (speed + 1) + 10) * 5 / 2;
+            pkt.e.period0           = ((speed + 1) * (speed + 1) + (speed + 1) + 10) * 5 / 2;
             pkt.e.effect_param0     = 7;
             pkt.e.effect_param1     = 1;
             break;
@@ -719,7 +853,8 @@ void RGBFusion2USBController::ResetController()
 | Check controller for gen2 ARGB support                    |
 |   Checks for supported device number                      |
 |   Then checks for supported controllers                   |
-|   Then checks for supported feature bit (SaveLEDState)    |
+|   Then checks for supported feature bit                   |
+|       (SetPersistentLighting)                             |
 |   Finally checks for strip detection value.               |
 \*---------------------------------------------------------*/
 bool RGBFusion2USBController::SupportsGen2() const
@@ -829,10 +964,10 @@ bool RGBFusion2USBController::ScanGen2Strips(uint8_t enabled_headers)
 
         dst.totalLeds               = total_leds;
 
-        SetLedCount(0, 0, 0, 0);
+        SetLedCount(0, 0, 0, 0, 0, 0);
         std::this_thread::sleep_for(std::chrono::milliseconds(20));
 
-        SaveLEDState(false);
+        SetPersistentLightingEnabled(false);
         std::this_thread::sleep_for(std::chrono::milliseconds(20));
     }
 
@@ -842,7 +977,7 @@ bool RGBFusion2USBController::ScanGen2Strips(uint8_t enabled_headers)
 /*---------------------------------------------------------*\
 | Check controller for persistent state support             |
 \*---------------------------------------------------------*/
-bool RGBFusion2USBController::SupportsSaveLEDState() const
+bool RGBFusion2USBController::SupportsSetPersistentLighting() const
 {
     return(report_loaded && (report.support_cmd_flag & 0x01));
 }

Controllers/GigabyteRGBFusion2USBController/GigabyteRGBFusion2USBController.h

@@ -4,7 +4,7 @@
 |   Driver for Gigabyte Aorus RGB Fusion 2 USB motherboard  |
 |                                                           |
 |   jackun                                      08 Jan 2020 |
-|   megadjc                                     31 Jul 2025 |
+|   megadjc                                     03 Sep 2026 |
 |                                                           |
 |   This file is part of the OpenRGB project                |
 |   SPDX-License-Identifier: GPL-2.0-or-later               |
@@ -20,6 +20,14 @@
 #include "GigabyteFusion2USB_Devices.h"
 
 #define FUSION2_USB_BUFFER_SIZE   64
+#define RGBFUSION2_DLED_LEDS_MIN  0
+#define RGBFUSION2_DLED_LEDS_MAX  1024
+
+/*--------------------------------------------------------*\
+| IT57xx only supports 256 LED strings                     |
+\*--------------------------------------------------------*/
+#define RGBFUSION2_57XX_LEDS_MIN  0
+#define RGBFUSION2_57XX_LEDS_MAX  256
 
 /*--------------------------------------------------------*\
 | Gen2 scan/info opcode base                               |
@@ -73,8 +81,8 @@ struct LEDs
 \*---------------------------------------------------------*/
 struct CalibrationData
 {
-    uint32_t dled[4]   = {0, 0, 0, 0};
-    uint32_t spare[4]  = {0, 0, 0, 0};
+    uint32_t dled[6]   = {0, 0, 0, 0, 0, 0};
+    uint32_t spare[2]  = {0, 0};
     uint32_t mainboard = 0;
 };
 
@@ -83,8 +91,8 @@ struct CalibrationData
 \*---------------------------------------------------------*/
 struct EncodedCalibration
 {
-    std::string dled[4];
-    std::string spare[4];
+    std::string dled[6];
+    std::string spare[2];
     std::string mainboard;
 };
 
@@ -176,6 +184,12 @@ union PktRGB
             case HDR_D_LED4:
                 header = HDR_D_LED4_ARGB;
                 break;
+            case LED10:
+                header = ONBOARD1_ARGB;
+                break;
+            case LED11:
+                header = ONBOARD2_ARGB;
+                break;
             default:
                 header = HDR_D_LED1_ARGB;
                 break;
@@ -271,9 +285,9 @@ struct IT8297Report
     uint8_t  device_num;
     uint8_t  strip_detect;
     uint32_t fw_ver;
-    uint8_t  curr_led_count_high;
-    uint8_t  curr_led_count_low;
-    uint8_t  strip_ctrl_length1;
+    uint8_t  argb01_count;
+    uint8_t  argb23_count;
+    uint8_t  argb45_count;
     uint8_t  support_cmd_flag;
     char     str_product[28];
     uint32_t cal_spare0;
@@ -293,8 +307,8 @@ struct IT5711Calibration
     uint8_t  reserved[3];
     uint32_t cal_strip2;
     uint32_t cal_strip3;
-    uint32_t cal_spare2;
-    uint32_t cal_spare3;
+    uint32_t cal_strip4;
+    uint32_t cal_strip5;
     uint8_t  padding[44];
 };
 
@@ -315,8 +329,8 @@ union CMD_0x33
         uint32_t c_spare1       = 0;
         uint32_t d_strip_c2     = 0;
         uint32_t d_strip_c3     = 0;
-        uint32_t c_spare2       = 0;
-        uint32_t c_spare3       = 0;
+        uint32_t d_strip_c4     = 0;
+        uint32_t d_strip_c5     = 0;
         uint8_t  reserved[25];
     } c;
 
@@ -336,14 +350,15 @@ public:
 
     bool                    ApplyEffect(bool batch_commit = false);
     bool                    SetCalibration(const EncodedCalibration& cal, bool refresh_from_hw);
-    void                    SetLedCount(unsigned int c0, unsigned int c1, unsigned int c2, unsigned int c3);
+    void                    SetLedCount(unsigned int c0, unsigned int c1, unsigned int c2, unsigned int c3, unsigned int c4, unsigned int c5);
     void                    SetLEDEffect(int led, int mode, unsigned int speed, unsigned char brightness, bool random, uint32_t* color);
     bool                    SetStripBuiltinEffectState(int hdr, bool enable);
     void                    SetStripColors(unsigned int hdr, RGBColor * colors, unsigned int num_colors, int single_led = -1);
     bool                    SupportsGen2() const;
     bool                    ScanGen2Strips(uint8_t hdr_mask);
-    bool                    SaveLEDState(bool enable);
-    bool                    SupportsSaveLEDState() const;
+    bool                    SupportsSetPersistentLighting() const;
+    bool                    SetPersistentLightingEnabled(bool enable);
+    bool                    SaveLightingStateToFlash();
 
     EncodedCalibration      GetCalibration(bool refresh_from_hw = false);
     std::string             GetDeviceName();
@@ -351,6 +366,8 @@ public:
     std::string             GetDeviceDescription();
     std::string             GetDeviceLocation();
     std::string             GetFWVersion();
+    uint8_t                 GetFWID();
+    uint8_t                 GetFWRevision();
     uint16_t                GetProductID();
     std::string             GetSerial();
     std::vector<Gen2StripInfo> ExportGen2Strips() const;
@@ -363,13 +380,13 @@ private:
     uint32_t                EncodeCalibrationBuffer(const std::string& rgb_order);
     bool                    RefreshHardwareInfo();
     void                    ResetController();
-    bool                    SaveCalState();
     bool                    SendCCReport(uint8_t a, uint8_t b, uint8_t c = 0);
     bool                    SendReport(uint8_t id, uint8_t a, uint8_t b, uint8_t c = 0);
     int                     SendPacket(unsigned char* packet);
 
     hid_device*             dev;
     uint8_t                 device_num;
+    uint8_t                 fw_id               = 0;
     uint16_t                product_id;
     uint32_t                effect_zone_mask    = 0;
     int                     mode;
@@ -384,8 +401,5 @@ private:
     int                     report_id           = 0xCC;
     bool                    report_loaded       = false;
     bool                    cali_loaded         = false;
-    LEDCount                D_LED1_count;
-    LEDCount                D_LED2_count;
-    LEDCount                D_LED3_count;
-    LEDCount                D_LED4_count;
+    LEDCount                ARGB_count[6];
 };

Controllers/GigabyteRGBFusion2USBController/GigabyteRGBFusion2USBControllerDetect.cpp

@@ -5,7 +5,7 @@
 |   motherboard                                             |
 |                                                           |
 |   jackun                                      08 Jan 2020 |
-|   megadjc                                     31 Jul 2025 |
+|   megadjc                                     03 Sep 2026 |
 |                                                           |
 |   This file is part of the OpenRGB project                |
 |   SPDX-License-Identifier: GPL-2.0-or-later               |

Controllers/GigabyteRGBFusion2USBController/RGBController_GigabyteRGBFusion2USB.h

@@ -5,7 +5,7 @@
 |   motherboard                                             |
 |                                                           |
 |   jackun                                      08 Jan 2020 |
-|   megadjc                                     31 Jul 2025 |
+|   megadjc                                     03 Sep 2026 |
 |                                                           |
 |   This file is part of the OpenRGB project                |
 |   SPDX-License-Identifier: GPL-2.0-or-later               |
@@ -13,35 +13,16 @@
 
 #pragma once
 
-#include <map>
 #include "RGBController.h"
 #include "GigabyteFusion2USB_Devices.h"
 #include "GigabyteRGBFusion2USBController.h"
-#include "SettingsManager.h"
 
-#define RGBFUSION2_DIGITAL_LEDS_MIN         0
-#define RGBFUSION2_DIGITAL_LEDS_MAX         1024
 #define RGBFUSION2_BRIGHTNESS_MIN           0
 #define RGBFUSION2_BRIGHTNESS_MAX           255
 #define RGBFUSION2_SPEED_MIN                9
 #define RGBFUSION2_SPEED_MID                4
 #define RGBFUSION2_SPEED_MAX                0
 
-#define GET_JSON_VAL_ELSE_OFF(obj, key) obj.contains(key) ? obj.at(key).get<std::string>() : std::string("OFF")
-
-template<typename K, typename V>
-static std::map<V, K> reverse_map(const std::map<K, V>& map)
-{
-    std::map<V, K> reversed_map;
-
-    for(const std::pair<K, V> entry : map)
-    {
-        reversed_map[entry.second] = entry.first;
-    }
-
-    return reversed_map;
-}
-
 class RGBController_RGBFusion2USB: public RGBController
 {
 public:
@@ -59,6 +40,8 @@ public:
     void                        DeviceUpdateMode();
     void                        DeviceUpdateZoneMode(int zone);
     void                        DeviceSaveMode() override;
+    void                        DeviceConfigureDevice() override;
+    void                        DeviceUpdateDeviceSpecificConfiguration() override;
 
 private:
     std::string                 detector_name;
@@ -67,6 +50,9 @@ private:
     uint8_t                     device_num;
     RGBColor                    null_color      = 0;
     bool                        supports_gen2   = 0;
+    uint8_t                     gen2_enabled_headers = 0;
+    bool                        entire_device_effect_active = false;
+    bool                        persist_lighting_on_exit    = false;
     /*---------------------------------------------------------*\
     | The intial value of device_index should point to the      |
     |   layout for the generic_device                           |
@@ -75,6 +61,8 @@ private:
     uint16_t                    product_id      = 0;
     uint32_t                    effects_mask    = 0;
     void                        Init_Controller();
+    void                        InitDeviceSpecificConfiguration();
+    void                        ApplyDeviceSpecificConfiguration(bool setup_zones);
     int                         GetLED_Zone(int led_idx);
 
     /*---------------------------------------------------------*\
@@ -84,16 +72,4 @@ private:
     gb_fusion2_layout           instance_zones{};
     std::vector<gb_fusion2_zone*> allocated_zones;
 
-    nlohmann::json              WriteCalJsonFrom(
-                                    const EncodedCalibration& src);
-    void                        FillMissingWith(
-                                    nlohmann::json& dst,
-                                    const EncodedCalibration& fb);
-    nlohmann::json              BuildCustomLayoutJson(
-                                    const gb_fusion2_device* layout,
-                                    const RvrseLedHeaders& reverseLookup);
-    void                        LoadCustomLayoutFromJson(
-                                    const nlohmann::json& json_custom,
-                                    const FwdLedHeaders& forwardLookup,
-                                    gb_fusion2_device* layout);
 };

Controllers/GoveeController/RGBController_Govee.cpp

@@ -16,22 +16,45 @@
 
 using namespace std::chrono_literals;
 
-struct GoveeHardwareInfo
+/*---------------------------------------------------------*\
+| A device's zone shape is picked from this fixed set of    |
+| known layouts rather than special-cased by SKU string, so |
+| adding a device that fits an existing shape is a one-line |
+| table entry rather than a new code path.                  |
+|                                                           |
+|   LINEAR      single strip, no matrix                     |
+|   SERPENTINE  matrix wired bottom-to-top, alternating     |
+|               scan direction each row (e.g. H6022)        |
+|   SPLIT_BARS  two disconnected bars either side of a gap, |
+|               e.g. two light bars flanking a monitor      |
+\*---------------------------------------------------------*/
+enum GoveeZoneLayout
+{
+    GOVEE_ZONE_LINEAR,
+    GOVEE_ZONE_SERPENTINE,
+    GOVEE_ZONE_SPLIT_BARS,
+};
+
+struct GoveeDeviceInfo
 {
     unsigned int    led_count;
-    unsigned int matrix_row_len;    // 0 = linear
+    GoveeZoneLayout layout;
+    unsigned int    matrix_row_len;    // SERPENTINE only: LEDs per row
+    unsigned int    gap_columns;       // SPLIT_BARS only: empty columns between the two bars
     bool            supports_razer;
 };
 
 const unsigned int GOVEE_FALLBACK_LED_COUNT = 1;
+#define GOVEE_MATRIX_LED_NONE                       0xFFFFFFFF
 
-static std::map<std::string, GoveeHardwareInfo> govee_hardware_info
+static std::map<std::string, GoveeDeviceInfo> govee_device_info
 {
-    { "H6022",   { 132, 12, true  } },    // Govee Smart Table Lamp 2
-    { "H612F",   { 12,  0,  true  } },    // Govee Strip Light S (3m)
-    { "H619A",   { 20,  0,  true  } },    // Govee RGBIC Led Strip Lights
-    { "H70B1",   { 20,  0,  true  } },    // Govee LED Curtain Lights
-    { "H607C",   { 174, 0,  true  } },    // Govee Floor Lamp 2
+    { "H6022",   { 132, GOVEE_ZONE_SERPENTINE, 12, 0,  true } },    // Govee Smart Table Lamp 2
+    { "H6046",   { 20,  GOVEE_ZONE_SPLIT_BARS, 0,  10, true } },    // Govee RGBIC Gaming Light Bars - two 10-LED bars, right then left
+    { "H612F",   { 12,  GOVEE_ZONE_LINEAR,     0,  0,  true } },    // Govee Strip Light S (3m)
+    { "H619A",   { 20,  GOVEE_ZONE_LINEAR,     0,  0,  true } },    // Govee RGBIC Led Strip Lights
+    { "H70B1",   { 20,  GOVEE_ZONE_LINEAR,     0,  0,  true } },    // Govee LED Curtain Lights
+    { "H607C",   { 174, GOVEE_ZONE_LINEAR,     0,  0,  true } },    // Govee Floor Lamp 2
 };
 
 enum
@@ -98,10 +121,10 @@ RGBController_Govee::~RGBController_Govee()
 
 void RGBController_Govee::SetupZones()
 {
-    GoveeHardwareInfo hw = { GOVEE_FALLBACK_LED_COUNT, 0, false };
+    GoveeDeviceInfo hw = { GOVEE_FALLBACK_LED_COUNT, GOVEE_ZONE_LINEAR, 0, 0, false };
 
-    std::map<std::string, GoveeHardwareInfo>::iterator it = govee_hardware_info.find(controller->GetSku());
-    if(it != govee_hardware_info.end())
+    std::map<std::string, GoveeDeviceInfo>::iterator it = govee_device_info.find(controller->GetSku());
+    if(it != govee_device_info.end())
     {
         hw = it->second;
         razer_supported = hw.supports_razer;
@@ -112,17 +135,60 @@ void RGBController_Govee::SetupZones()
     strip.leds_min              = hw.led_count;
     strip.leds_max              = hw.led_count;
 
-    if(hw.matrix_row_len == 0)
+    switch(hw.layout)
+    {
+        case GOVEE_ZONE_LINEAR:
         {
             strip.name              = "Govee Strip";
             strip.type              = ZONE_TYPE_LINEAR;
+            break;
         }
-    else
+
+        case GOVEE_ZONE_SPLIT_BARS:
+        {
+            strip.name              = "Light Bars";
+            strip.type              = ZONE_TYPE_MATRIX;
+
+            unsigned int bar_leds   = hw.led_count / 2;
+            unsigned int width      = hw.gap_columns + 2;
+            unsigned int height     = bar_leds;
+
+            strip.matrix_map.Set(height, width, NULL);
+
+            /*-------------------------------------------------*\
+            | The two bars stand either side of a monitor, so   |
+            | the left bar takes the first column and the right |
+            | bar the last one.  The columns between them are   |
+            | empty and represent the gap across the desk,      |
+            | which keeps horizontal effects moving at the same |
+            | rate as they appear to the eye.                   |
+            \*-------------------------------------------------*/
+            for(unsigned int y = 0; y < height; y++)
+            {
+                for(unsigned int x = 0; x < width; x++)
+                {
+                    strip.matrix_map.map[(y * width) + x] = GOVEE_MATRIX_LED_NONE;
+                }
+
+                strip.matrix_map.map[(y * width)]                 = bar_leds + y;
+                strip.matrix_map.map[(y * width) + (width - 1)]   = y;
+            }
+            break;
+        }
+
+        case GOVEE_ZONE_SERPENTINE:
+        default:
         {
             strip.name              = "Govee Matrix";
             strip.type              = ZONE_TYPE_MATRIX;
 
-        unsigned int width      = hw.matrix_row_len;
+            /*-------------------------------------------------*\
+            | matrix_row_len is only meaningful for this layout |
+            | - guard a table entry that forgets to set it so a |
+            | bad row degrades to a single column instead of    |
+            | dividing by zero.                                 |
+            \*-------------------------------------------------*/
+            unsigned int width      = (hw.matrix_row_len > 0) ? hw.matrix_row_len : 1;
             unsigned int height     = hw.led_count / width;
 
             strip.matrix_map.height = height;
@@ -130,8 +196,8 @@ void RGBController_Govee::SetupZones()
             strip.matrix_map.map.resize(hw.led_count);
 
             /*-------------------------------------------------*\
-        | On H6022, LEDs indexed bottom to top, alternating |
-        | clockwise and counterclockwise for each row.      |
+            | LEDs indexed bottom to top, alternating clockwise |
+            | and counterclockwise for each row (e.g. H6022).   |
             \*-------------------------------------------------*/
             for(unsigned int y = 0; y < height; y++)
             {
@@ -152,13 +218,33 @@ void RGBController_Govee::SetupZones()
                     strip.matrix_map.map[y * width + x] = led_y * width + led_x;
                 }
             }
+            break;
+        }
     }
     zones.push_back(strip);
 
     for(std::size_t led_idx = 0; led_idx < strip.leds_count; led_idx++)
     {
         led strip_led;
+
+        if(hw.layout == GOVEE_ZONE_SPLIT_BARS)
+        {
+            unsigned int bar_leds = hw.led_count / 2;
+
+            if(led_idx < bar_leds)
+            {
+                strip_led.name  = "Right Bar LED " + std::to_string(led_idx + 1);
+            }
+            else
+            {
+                strip_led.name  = "Left Bar LED " + std::to_string(led_idx - (bar_leds - 1));
+            }
+        }
+        else
+        {
             strip_led.name      = "Govee LED " + std::to_string(led_idx);
+        }
+
         leds.push_back(strip_led);
     }
 
@@ -288,6 +374,23 @@ void RGBController_Govee::KeepaliveThread()
             {
                 UpdateStatic(true);
             }
+            else if(modes[active_mode].value == GOVEE_MODE_DIRECT)
+            {
+                /*-----------------------------------------------------*\
+                | Direct/per-LED mode has no other periodic refresh -   |
+                | SendRazerEnable() only fires once, at mode entry.     |
+                | Re-assert it here so a long gap between real updates  |
+                | (e.g. idle time between plugin-driven alerts) can't   |
+                | let the device's external-control session time out    |
+                | and fall back to its own firmware default.            |
+                \*-----------------------------------------------------*/
+                if(razer_supported)
+                {
+                    controller->SendRazerEnable();
+                }
+
+                DeviceUpdateLEDs();
+            }
         }
 
         std::this_thread::sleep_for(10s);

Controllers/HIDLampArrayController/HIDLampArrayController.cpp

@@ -31,7 +31,7 @@ HIDLampArrayController::HIDLampArrayController(hid_device *dev_handle, const cha
     unsigned int  pos                   = 0;
     unsigned char report_descriptor[HID_API_MAX_REPORT_DESCRIPTOR_SIZE];
     unsigned char report_id             = 0;
-    unsigned int  size                  = hid_get_report_descriptor(dev, report_descriptor, sizeof(report_descriptor));
+    int           size                  = hid_get_report_descriptor(dev, report_descriptor, sizeof(report_descriptor));
     unsigned int  usage                 = 0;
     unsigned char usage_page            = 0;
 
@@ -40,7 +40,18 @@ HIDLampArrayController::HIDLampArrayController(hid_device *dev_handle, const cha
     \*-----------------------------------------------------*/
     std::unordered_map<unsigned int, unsigned int> usage_to_report_id;
 
-    while(pos < size)
+    /*-----------------------------------------------------*\
+    | A failed descriptor read returns -1; treated as a     |
+    | length it walks off the end of the buffer.            |
+    \*-----------------------------------------------------*/
+    if(size < 0)
+    {
+        LampArray.LampCount     = 0;
+        LampArray.LampArrayKind = HID_LAMPARRAY_KIND_UNDEFINED;
+        return;
+    }
+
+    while(pos < (unsigned int)size)
     {
         get_hid_item_size(report_descriptor, size, pos, &data_len, &key_size);
 

Controllers/HIDLampArrayController/RGBController_HIDLampArray.cpp

@@ -83,6 +83,8 @@ RGBController_HIDLampArray::RGBController_HIDLampArray(HIDLampArrayController* c
 
 RGBController_HIDLampArray::~RGBController_HIDLampArray()
 {
+    Shutdown();
+
     delete controller;
 }
 
@@ -194,7 +196,7 @@ static const char *HIDUsageIDsToKeyNames[HID_KEYBOARD_USAGE_IDS_COUNT] =
     KEY_EN_NUMPAD_0,            // Keypad 0 and Insert
     KEY_EN_NUMPAD_PERIOD,       // Keypad . and Delete
     KEY_EN_BACK_SLASH,          // Keyboard Non-US \ and |
-    KEY_EN_UNUSED,              // Keyboard Application
+    KEY_EN_MENU,                // Keyboard Application
     KEY_EN_POWER,               // Keyboard Power
     KEY_EN_NUMPAD_EQUAL,        // Keypad =
     KEY_EN_F13,                 // Keyboard F13
@@ -258,6 +260,16 @@ static const char *HIDUsageIDsToKeyNames[HID_KEYBOARD_USAGE_IDS_COUNT] =
     KEY_EN_UNUSED,              // Keyboard Clear/Again
     KEY_EN_UNUSED,              // Keyboard CrSel/Props
     KEY_EN_UNUSED,              // Keyboard ExSel
+    KEY_EN_UNUSED,              // A5 Reserved
+    KEY_EN_UNUSED,              // A6 Reserved
+    KEY_EN_UNUSED,              // A7 Reserved
+    KEY_EN_UNUSED,              // A8 Reserved
+    KEY_EN_UNUSED,              // A9 Reserved
+    KEY_EN_UNUSED,              // AA Reserved
+    KEY_EN_UNUSED,              // AB Reserved
+    KEY_EN_UNUSED,              // AC Reserved
+    KEY_EN_UNUSED,              // AD Reserved
+    KEY_EN_UNUSED,              // AE Reserved
     KEY_EN_UNUSED,              // AF Reserved
     KEY_EN_UNUSED,              // Keypad 00
     KEY_EN_UNUSED,              // Keypad 000
@@ -305,6 +317,7 @@ static const char *HIDUsageIDsToKeyNames[HID_KEYBOARD_USAGE_IDS_COUNT] =
     KEY_EN_UNUSED,              // Keypad Octal
     KEY_EN_UNUSED,              // Keypad Decimal
     KEY_EN_UNUSED,              // Keypad Hexadecimal
+    KEY_EN_UNUSED,              // DE Reserved
     KEY_EN_UNUSED,              // DF Reserved
     KEY_EN_LEFT_CONTROL,        // Keyboard LeftControl
     KEY_EN_LEFT_SHIFT,          // Keyboard LeftShift
@@ -334,8 +347,8 @@ void RGBController_HIDLampArray::SetupZones()
         columns.insert(controller->GetLamps()[lamp_idx].PositionXInMicrometers);
     }
 
-    new_zone.matrix_map.height  = rows.size();
-    new_zone.matrix_map.width   = columns.size();
+    new_zone.matrix_map.height  = (unsigned int)rows.size();
+    new_zone.matrix_map.width   = (unsigned int)columns.size();
     new_zone.matrix_map.map.resize(rows.size() * columns.size());
 
     memset(new_zone.matrix_map.map.data(), 0xFF, (new_zone.matrix_map.map.size() * sizeof(unsigned int)));
@@ -346,7 +359,7 @@ void RGBController_HIDLampArray::SetupZones()
         size_t idx      = std::distance(columns.begin(), columns.find(controller->GetLamps()[lamp_idx].PositionXInMicrometers));
         size_t idy      = std::distance(rows.begin(), rows.find(controller->GetLamps()[lamp_idx].PositionYInMicrometers));
 
-        new_zone.matrix_map.map[idx + idy * new_zone.matrix_map.width] = lamp_idx;
+        new_zone.matrix_map.map[idx + idy * new_zone.matrix_map.width] = (unsigned int)lamp_idx;
     }
 
     zones.push_back(new_zone);
@@ -355,9 +368,11 @@ void RGBController_HIDLampArray::SetupZones()
     {
         led new_led;
 
-        if(controller->GetLamps()[lamp_idx].LampKey < HID_KEYBOARD_USAGE_IDS_COUNT)
+        unsigned char lamp_key = controller->GetLamps()[lamp_idx].LampKey;
+
+        if(lamp_key < HID_KEYBOARD_USAGE_IDS_COUNT && HIDUsageIDsToKeyNames[lamp_key] != nullptr)
         {
-            new_led.name = HIDUsageIDsToKeyNames[controller->GetLamps()[lamp_idx].LampKey];
+            new_led.name = HIDUsageIDsToKeyNames[lamp_key];
         }
         else
         {
@@ -371,7 +386,7 @@ void RGBController_HIDLampArray::SetupZones()
 
 void RGBController_HIDLampArray::DeviceUpdateLEDs()
 {
-    unsigned int leds_to_go = leds.size();
+    unsigned int leds_to_go = (unsigned int)leds.size();
 
     while(leds_to_go > 0)
     {
@@ -387,7 +402,7 @@ void RGBController_HIDLampArray::DeviceUpdateLEDs()
 
         for(unsigned int led_frame_idx = 0; led_frame_idx < leds_this_frame; led_frame_idx++)
         {
-            unsigned short led_idx = (leds.size() - leds_to_go) + led_frame_idx;
+            unsigned short led_idx = (unsigned short)((leds.size() - leds_to_go) + led_frame_idx);
             LampIds[led_frame_idx] = led_idx;
             UpdateColors[led_frame_idx].RedChannel = RGBGetRValue(colors[led_idx]);
             UpdateColors[led_frame_idx].GreenChannel = RGBGetGValue(colors[led_idx]);

Controllers/HyperXMicrophoneV2Controller/RGBController_HyperXMicrophoneV2.cpp

@@ -85,7 +85,7 @@ void RGBController_HyperXMicrophoneV2::SetupZones()
     Mic.leds_min                = HYPERX_QUADCAST_2S_TOTAL_LEDS;
     Mic.leds_max                = HYPERX_QUADCAST_2S_TOTAL_LEDS;
     Mic.leds_count              = HYPERX_QUADCAST_2S_TOTAL_LEDS;
-    Mic.matrix_map.Set(HYPERX_QUADCAST_2S_MATRIX_WIDTH, HYPERX_QUADCAST_2S_MATRIX_HEIGHT, led_mapping);
+    Mic.matrix_map.Set(HYPERX_QUADCAST_2S_MATRIX_HEIGHT, HYPERX_QUADCAST_2S_MATRIX_WIDTH, led_mapping);
 
     for(unsigned int i = 0; i < HYPERX_QUADCAST_2S_TOTAL_LEDS; i ++)
     {

Controllers/LogitechController/LogitechControllerDetect.cpp

@@ -20,9 +20,6 @@
 #include "LogitechG213Controller.h"
 #include "LogitechG600Controller.h"
 #include "LogitechG933Controller.h"
-#include "LogitechG810Controller.h"
-#include "LogitechGProKeyboardController.h"
-#include "LogitechG910Controller.h"
 #include "LogitechG815Controller.h"
 #include "LogitechG915Controller.h"
 #include "LogitechGLightsyncController.h"
@@ -32,9 +29,6 @@
 #include "RGBController_LogitechG213.h"
 #include "RGBController_LogitechG600.h"
 #include "RGBController_LogitechG933.h"
-#include "RGBController_LogitechG810.h"
-#include "RGBController_LogitechGProKeyboard.h"
-#include "RGBController_LogitechG910.h"
 #include "RGBController_LogitechG815.h"
 #include "RGBController_LogitechG915.h"
 #include "RGBController_LogitechGLightsync.h"
@@ -61,12 +55,6 @@ using namespace std::chrono_literals;
 | Keyboard product IDs                                      |
 \*---------------------------------------------------------*/
 #define LOGITECH_G213_PID                           0xC336
-#define LOGITECH_G512_PID                           0xC342
-#define LOGITECH_G512_RGB_PID                       0xC33C
-#define LOGITECH_G610_1_PID                         0xC333
-#define LOGITECH_G610_2_PID                         0xC338
-#define LOGITECH_G810_1_PID                         0xC331
-#define LOGITECH_G810_2_PID                         0xC337
 #define LOGITECH_G813_PID                           0xC232
 #define LOGITECH_G815_PID                           0xC33F
 #define LOGITECH_G915_WIRED_PID                     0xC33E
@@ -74,9 +62,6 @@ using namespace std::chrono_literals;
 #define LOGITECH_G915_RECEIVER_2_PID                0xC547
 #define LOGITECH_G915TKL_WIRED_PID                  0xC343
 #define LOGITECH_G915TKL_RECEIVER_PID               0xC545
-#define LOGITECH_G910_ORION_SPARK_PID               0xC32B
-#define LOGITECH_G910_PID                           0xC335
-#define LOGITECH_GPRO_KEYBOARD_1_PID                0xC339
 
 /*---------------------------------------------------------*\
 | Mouse product IDs                                         |
@@ -172,112 +157,6 @@ DetectedControllers DetectLogitechKeyboardG213(hid_device_info* info, const std:
     return(detected_controllers);
 }
 
-DetectedControllers DetectLogitechKeyboardG810(hid_device_info* info, const std::string& name)
-{
-    /*-----------------------------------------------------*\
-    | Logitech keyboards use two different usages, one for  |
-    | 20-byte packets and one for 64-byte packets.  Usage   |
-    | 0x0602 for 20 byte, usage 0x0604 for 64 byte, both    |
-    | are on usage page 0xFF43                              |
-    \*-----------------------------------------------------*/
-    DetectedControllers detected_controllers;
-
-    hid_device* dev_usage_0x0602 = nullptr;
-    hid_device* dev_usage_0x0604 = nullptr;
-    hid_device_info* info_temp = info;
-
-    while(info_temp)
-    {
-        if(info_temp->vendor_id        == info->vendor_id           // constant LOGITECH_VID
-        && info_temp->product_id       == info->product_id          // NON-constant
-        && info_temp->interface_number == info->interface_number    // constant 1
-        && info_temp->usage_page       == info->usage_page)         // constant 0xFF43
-        {
-            if(info_temp->usage == 0x0602)
-            {
-                dev_usage_0x0602 = hid_open_path(info_temp->path);
-            }
-            else if(info_temp->usage == 0x0604)
-            {
-                dev_usage_0x0604 = hid_open_path(info_temp->path);
-            }
-        }
-        if(dev_usage_0x0602 && dev_usage_0x0604)
-        {
-            break;
-        }
-        info_temp = info_temp->next;
-    }
-    if(dev_usage_0x0602 && dev_usage_0x0604)
-    {
-        LogitechG810Controller*     controller     = new LogitechG810Controller(dev_usage_0x0602, dev_usage_0x0604, info->path, name);
-        RGBController_LogitechG810* rgb_controller = new RGBController_LogitechG810(controller);
-
-        detected_controllers.push_back(rgb_controller);
-    }
-    else
-    {
-        // Not all of them could be opened, do some cleanup
-        hid_close(dev_usage_0x0602);
-        hid_close(dev_usage_0x0604);
-    }
-
-    return(detected_controllers);
-}
-
-DetectedControllers DetectLogitechKeyboardG910(hid_device_info* info, const std::string& name)
-{
-    /*-----------------------------------------------------*\
-    | Logitech keyboards use two different usages, one for  |
-    | 20-byte packets and one for 64-byte packets.  Usage   |
-    | 0x0602 for 20 byte, usage 0x0604 for 64 byte, both    |
-    | are on usage page 0xFF43                              |
-    \*-----------------------------------------------------*/
-    DetectedControllers detected_controllers;
-
-    hid_device* dev_usage_0x0602 = nullptr;
-    hid_device* dev_usage_0x0604 = nullptr;
-    hid_device_info* info_temp = info;
-
-    while(info_temp)
-    {
-        if(info_temp->vendor_id        == info->vendor_id           // constant LOGITECH_VID
-        && info_temp->product_id       == info->product_id          // NON-constant
-        && info_temp->interface_number == info->interface_number    // constant 1
-        && info_temp->usage_page       == info->usage_page)         // constant 0xFF43
-        {
-            if(info_temp->usage == 0x0602)
-            {
-                dev_usage_0x0602 = hid_open_path(info_temp->path);
-            }
-            else if(info_temp->usage == 0x0604)
-            {
-                dev_usage_0x0604 = hid_open_path(info_temp->path);
-            }
-        }
-        if(dev_usage_0x0602 && dev_usage_0x0604)
-        {
-            break;
-        }
-        info_temp = info_temp->next;
-    }
-    if(dev_usage_0x0602 && dev_usage_0x0604)
-    {
-        LogitechG910Controller*     controller     = new LogitechG910Controller(dev_usage_0x0602, dev_usage_0x0604, info->path, name);
-        RGBController_LogitechG910* rgb_controller = new RGBController_LogitechG910(controller);
-
-        detected_controllers.push_back(rgb_controller);
-    }
-    else
-    {
-        // Not all of them could be opened, do some cleanup
-        hid_close(dev_usage_0x0602);
-        hid_close(dev_usage_0x0604);
-    }
-
-    return(detected_controllers);
-}
-
 DetectedControllers DetectLogitechKeyboardG815(hid_device_info* info, const std::string& name)
 {
     /*-----------------------------------------------------*\
@@ -431,8 +310,9 @@ DetectedControllers DetectLogitechKeyboardG915Receiver2(hid_device_info* info, c
             {
                 /*-----------------------------------------*\
                 | G915 X family: the unified HID++ 2.0      |
-                | controller handles it. Skip so the C547   |
-                | detector claims it.                       |
+                | controller handles it. Skip so the        |
+                | unified detector, registered after this   |
+                | one, claims it.                           |
                 \*-----------------------------------------*/
                 LOG_DEBUG("[LogitechControllerDetect] 0xC547 G915 X -> unified controller, skipping legacy");
                 hid_close(dev);
@@ -493,59 +373,6 @@ DetectedControllers DetectLogitechKeyboardG915Wired(hid_device_info* info, const
     return(detected_controllers);
 }
 
-DetectedControllers DetectLogitechKeyboardGPro(hid_device_info* info, const std::string& name)
-{
-    /*-----------------------------------------------------*\
-    | Logitech keyboards use two different usages, one for  |
-    | 20-byte packets and one for 64-byte packets.  Usage   |
-    | 0x0602 for 20 byte, usage 0x0604 for 64 byte, both    |
-    | are on usage page 0xFF43                              |
-    \*-----------------------------------------------------*/
-    DetectedControllers detected_controllers;
-
-    hid_device* dev_usage_0x0602 = nullptr;
-    hid_device* dev_usage_0x0604 = nullptr;
-    hid_device_info* info_temp = info;
-
-    while(info_temp)
-    {
-        if(info_temp->vendor_id        == info->vendor_id           // constant LOGITECH_VID
-        && info_temp->product_id       == info->product_id          // NON-constant
-        && info_temp->interface_number == info->interface_number    // constant 1
-        && info_temp->usage_page       == info->usage_page)         // constant 0xFF43
-        {
-            if(info_temp->usage == 0x0602)
-            {
-                dev_usage_0x0602 = hid_open_path(info_temp->path);
-            }
-            else if(info_temp->usage == 0x0604)
-            {
-                dev_usage_0x0604 = hid_open_path(info_temp->path);
-            }
-        }
-        if(dev_usage_0x0602 && dev_usage_0x0604)
-        {
-            break;
-        }
-        info_temp = info_temp->next;
-    }
-    if(dev_usage_0x0602 && dev_usage_0x0604)
-    {
-        LogitechGProKeyboardController*     controller     = new LogitechGProKeyboardController(dev_usage_0x0602, dev_usage_0x0604, name);
-        RGBController_LogitechGProKeyboard* rgb_controller = new RGBController_LogitechGProKeyboard(controller);
-
-        detected_controllers.push_back(rgb_controller);
-    }
-    else
-    {
-        // Not all of them could be opened, do some cleanup
-        hid_close(dev_usage_0x0602);
-        hid_close(dev_usage_0x0604);
-    }
-
-    return(detected_controllers);
-}
-
 /*---------------------------------------------------------*\
 | Logitech Mice                                             |
 \*---------------------------------------------------------*/
@@ -998,6 +825,16 @@ static bool HIDPP20ClaimDevice(const std::string& device_id)
     return hidpp20_claimed_devices.insert(device_id).second;
 }
 
+/*---------------------------------------------------------*\
+| Free the device claim when the device is unplugged        |
+\*---------------------------------------------------------*/
+static bool HIDPP20UnclaimDevice(const std::string& device_id)
+{
+    std::lock_guard<std::mutex> lock(hidpp20_registry_mutex);
+
+    return hidpp20_claimed_devices.erase(device_id);
+}
+
 /*---------------------------------------------------------*\
 | Watchers own threads and a node handle, so they have to   |
 | be stopped before the process exits.                      |
@@ -1380,7 +1217,7 @@ static bool HIDPP20LookupTarget(const std::string& node_path, uint8_t index, HID
 | lighting; both leave the target on file, so a device      |
 | that was asleep is built when its dongle reports it.      |
 \*---------------------------------------------------------*/
-static RGBController_LogitechHIDPP20* HIDPP20BuildController(const HIDPP20BuildTarget& target)
+static RGBController_LogitechHIDPP20* HIDPP20BuildController(const HIDPP20BuildTarget& target, const std::string& device_id="")
 {
     HIDPP20BuildClaim claim(target.node_path, target.index);
 
@@ -1466,7 +1303,7 @@ static RGBController_LogitechHIDPP20* HIDPP20BuildController(const HIDPP20BuildT
     {
         controller->Initialize();
 
-        RGBController_LogitechHIDPP20* rgb_controller = new RGBController_LogitechHIDPP20(controller);
+        RGBController_LogitechHIDPP20* rgb_controller = new RGBController_LogitechHIDPP20(controller, [device_id](){HIDPP20UnclaimDevice(device_id);});
 
         /*-------------------------------------------------*\
         | Reader and power threads from the start, so we    |
@@ -1569,7 +1406,7 @@ static DetectedControllers HIDPP20Create(hid_device_info* info, const std::strin
 
     HIDPP20RecordTarget(target);
 
-    RGBController_LogitechHIDPP20* rgb_controller = HIDPP20BuildController(target);
+    RGBController_LogitechHIDPP20* rgb_controller = HIDPP20BuildController(target, device_id);
 
     if(rgb_controller != nullptr)
     {
@@ -1684,29 +1521,6 @@ DetectedControllers DetectLogitechHIDPP20(hid_device_info* info, const std::stri
     return(detected);
 }
 
-/*-------------------------------------------------------------------------------------------------------------------------------------*\
-| Unified HID++ 2.0: generic detection. These run only for devices with no *enabled* VID/PID-specific detector, disabling a legacy      |
-| controller in Settings hands its hardware over on the next detection. That is the migration path: no code change, and no risk to a    |
-| device whose legacy controller stays enabled.                                                                                         |
-|                                                                                                                                       |
-| The registrations cover every legacy transport signature:                                                                             |
-|  any interface, 0xFF00 usage 2    standard HID++ long report (modern keyboards/mice, receivers, G915 family, wired Lightspeed mice).  |
-|                                   Usage 2 is the collection we write to, on Windows, the only one that accepts our writes.            |
-|  any interface, 0xFF43 any usage  keyboards (G213/G512/G610/G810/G813/G815/G910/G Pro), the G560 speaker, the                         |
-|                                   G933 headset, and Bluetooth nodes. Not interface-keyed: a Bluetooth node                            |
-|                                   reports interface -1, which is also HID_INTERFACE_ANY, so it can never match.                       |
-|  interface 1, 0xFF00 any usage    older mice whose HID++ collection is not the usage-2 one                                            |
-|  any interface, 0xFFA0 usage 1    Centurion (G522, PRO X 2)                                                                           |
-|                                                                                                                                       |
-| Not covered, deliberately: the G600 (page 0xFF80) and the X56 (own VID) are not HID++ 2.0. A matching non-HID++ node costs one failed |
-| probe, ProbeIdentity changes nothing on the device. Receivers are recognized at runtime: the device probe fails and the pairing table |
-| answers; paired slots follow the same enabled/disabled rule (hidpp20_legacy_wireless_pids).                                           |
-\*-------------------------------------------------------------------------------------------------------------------------------------*/
-REGISTER_HID_DETECTOR_PU_ONLY ("Logitech HID++ 2.0", DetectLogitechHIDPP20, 0xFF00, 2);
-REGISTER_HID_DETECTOR_P_ONLY  ("Logitech HID++ 2.0", DetectLogitechHIDPP20, 0xFF43);
-REGISTER_HID_DETECTOR_IP_ONLY ("Logitech HID++ 2.0", DetectLogitechHIDPP20, 1, 0xFF00);
-REGISTER_HID_DETECTOR_PU_ONLY ("Logitech HID++ 2.0", DetectLogitechHIDPP20, 0xFFA0, 1);
-
 REGISTER_CUSTOM_UDEV_RULE(logitech_hidpp20, "Logitech HID++ 2.0", "SUBSYSTEM==\"hidraw\", ATTRS{idVendor}==\"046d\", TAG+=\"uaccess\", TAG+=\"Logitech_HID_20\"\nSUBSYSTEM==\"usb\", ATTR{idVendor}==\"046d\", TAG+=\"uaccess\", TAG+=\"Logitech_HID_20\"");
 REGISTER_CUSTOM_UDEV_RULE(logitech_g560, "Logitech G560 Lightsync Speaker", "SUBSYSTEMS==\"usb|hidraw\", ATTRS{idVendor}==\"046d\", ATTRS{idProduct}==\"0a78\", TAG+=\"uaccess\", TAG+=\"Logitech_G560_Lightsync_Speaker\"");
 
@@ -1714,35 +1528,14 @@ REGISTER_CUSTOM_UDEV_RULE(logitech_g560, "Logitech G560 Lightsync Speaker", "SUB
 | Keyboards                                                                                                                                         |
 \*-------------------------------------------------------------------------------------------------------------------------------------------------*/
 REGISTER_HID_DETECTOR_IPU("Logitech G213",                                  DetectLogitechKeyboardG213, LOGITECH_VID, LOGITECH_G213_PID,                    1, 0xFF43, 0x0602);
-REGISTER_HID_DETECTOR_IP ("Logitech G512",                                  DetectLogitechKeyboardG810, LOGITECH_VID, LOGITECH_G512_PID,                    1, 0xFF43);
-REGISTER_HID_DETECTOR_IP ("Logitech G512 RGB",                              DetectLogitechKeyboardG810, LOGITECH_VID, LOGITECH_G512_RGB_PID,                1, 0xFF43);
-REGISTER_HID_DETECTOR_IP ("Logitech G610 Orion",                            DetectLogitechKeyboardG810, LOGITECH_VID, LOGITECH_G610_1_PID,                  1, 0xFF43);
-REGISTER_HID_DETECTOR_IP ("Logitech G610 Orion",                            DetectLogitechKeyboardG810, LOGITECH_VID, LOGITECH_G610_2_PID,                  1, 0xFF43);
-REGISTER_HID_DETECTOR_IP ("Logitech G810 Orion Spectrum",                   DetectLogitechKeyboardG810, LOGITECH_VID, LOGITECH_G810_1_PID,                  1, 0xFF43);
-REGISTER_HID_DETECTOR_IP ("Logitech G810 Orion Spectrum",                   DetectLogitechKeyboardG810, LOGITECH_VID, LOGITECH_G810_2_PID,                  1, 0xFF43);
 REGISTER_HID_DETECTOR_IP ("Logitech G813 RGB Mechanical Gaming Keyboard",   DetectLogitechKeyboardG815, LOGITECH_VID, LOGITECH_G813_PID,                    1, 0xFF43);
 REGISTER_HID_DETECTOR_IP ("Logitech G815 RGB Mechanical Gaming Keyboard",   DetectLogitechKeyboardG815, LOGITECH_VID, LOGITECH_G815_PID,                    1, 0xFF43);
-REGISTER_HID_DETECTOR_IP ("Logitech G910 Orion Spark",                      DetectLogitechKeyboardG910, LOGITECH_VID, LOGITECH_G910_ORION_SPARK_PID,        1, 0xFF43);
-REGISTER_HID_DETECTOR_IP ("Logitech G910 Orion Spectrum",                   DetectLogitechKeyboardG910, LOGITECH_VID, LOGITECH_G910_PID,                    1, 0xFF43);
-REGISTER_HID_DETECTOR_IP ("Logitech G Pro RGB Mechanical Gaming Keyboard",  DetectLogitechKeyboardGPro, LOGITECH_VID, LOGITECH_GPRO_KEYBOARD_1_PID,         1, 0xFF43);
 
 REGISTER_HID_DETECTOR_IPU("Logitech G915 Wireless RGB Mechanical Gaming Keyboard",              DetectLogitechKeyboardG915,      LOGITECH_VID, LOGITECH_G915_RECEIVER_PID,      2, 0xFF00, 2);
 REGISTER_HID_DETECTOR_IPU("Logitech G915 Wireless RGB Mechanical Gaming Keyboard (Receiver 2)", DetectLogitechKeyboardG915Receiver2, LOGITECH_VID, LOGITECH_G915_RECEIVER_2_PID, 2, 0xFF00, 2);
 REGISTER_HID_DETECTOR_IPU("Logitech G915 Wireless RGB Mechanical Gaming Keyboard (Wired)",      DetectLogitechKeyboardG915Wired, LOGITECH_VID, LOGITECH_G915_WIRED_PID,         2, 0xFF00, 2);
 REGISTER_HID_DETECTOR_IPU("Logitech G915TKL Wireless RGB Mechanical Gaming Keyboard",           DetectLogitechKeyboardG915,      LOGITECH_VID, LOGITECH_G915TKL_RECEIVER_PID,   2, 0xFF00, 2);
 REGISTER_HID_DETECTOR_IPU("Logitech G915TKL Wireless RGB Mechanical Gaming Keyboard (Wired)",   DetectLogitechKeyboardG915Wired, LOGITECH_VID, LOGITECH_G915TKL_WIRED_PID,      2, 0xFF00, 2);
-/*---------------------------------------------------------*\
-| C547 carve-out: the legacy G915 Receiver 2 registration   |
-| above makes C547 a VID/PID-specific match, which          |
-| suppresses the generic HID++ 2.0 detector for every C547  |
-| node, including receivers with non-G915 devices paired.   |
-| This specific entry runs after the G915 detector          |
-| (registration order); when that returns nothing, the      |
-| unified pairing-table enumeration takes the receiver.     |
-| Literal PID: the macro token-pastes the object name and   |
-| LOGITECH_G915_RECEIVER_2_PID is already used above.       |
-\*---------------------------------------------------------*/
-REGISTER_HID_DETECTOR_IPU("Logitech HID++ 2.0 (C547 receiver)", DetectLogitechHIDPP20, LOGITECH_VID, 0xC547, 2, 0xFF00, 2);
 /*-------------------------------------------------------------------------------------------------------------------------------------------------*\
 | Mice                                                                                                                                              |
 \*-------------------------------------------------------------------------------------------------------------------------------------------------*/
@@ -1973,3 +1766,31 @@ REGISTER_HID_DETECTOR_IPU("Logitech G733 Gaming Headset",
 REGISTER_HID_DETECTOR_IPU("Logitech G733 Gaming Headset",                       DetectLogitechWired,        LOGITECH_VID, LOGITECH_G733_2_PID,                          3, 0xFF43, 514);
 REGISTER_HID_DETECTOR_IPU("Logitech G733 Gaming Headset",                       DetectLogitechWired,        LOGITECH_VID, LOGITECH_G733_3_PID,                          3, 0xFF43, 514);
 REGISTER_HID_DETECTOR_IPU("Logitech G935 Gaming Headset",                       DetectLogitechWired,        LOGITECH_VID, LOGITECH_G935_PID,                            3, 0xFF43, 514);
+
+/*-------------------------------------------------------------------------------------------------------------------------------------*\
+| Unified HID++ 2.0. Keyed to the Logitech VID, so these are specific detectors and no generic detector runs on a Logitech node;        |
+| HID LampArray in particular, which the official app publishes as a virtual device for older boards. Registered last on purpose:       |
+| specific detectors run in registration order and the first to return a controller wins, so a legacy controller keeps its device       |
+| while its detector is enabled, and disabling it in Settings hands the device over on the next detection.                              |
+|                                                                                                                                       |
+| USB, every legacy transport signature:                                                                                                |
+|  0xFF00 usage 2                   standard HID++ long report (modern keyboards/mice, receivers, G915 family, wired Lightspeed mice).  |
+|                                   Usage 2 is the collection we write to, on Windows, the only one that accepts our writes.            |
+|  0xFF43 any usage                 keyboards (G213/G512/G610/G810/G813/G815/G910/G Pro), the G560 speaker, the G933 headset            |
+|  interface 1, 0xFF00 any usage    older mice whose HID++ collection is not the usage-2 one. No bus key: an interface number           |
+|                                   only exists on USB.                                                                                 |
+|  0xFFA0 usage 1                   Centurion (G522, PRO X 2)                                                                           |
+| Bluetooth, which reports no interface number:                                                                                         |
+|  0xFF43 any usage                 G-series keyboards (G515)                                                                           |
+|  0xFF00 usage 2                   mice, the collection Solaar drives them on                                                          |
+|                                                                                                                                       |
+| Not covered, deliberately: the G600 (page 0xFF80) and the X56 (own VID) are not HID++ 2.0. A matching non-HID++ node costs one failed |
+| probe, ProbeIdentity changes nothing on the device. Receivers are recognized at runtime: the device probe fails and the pairing table |
+| answers; paired slots follow the same enabled/disabled rule (hidpp20_legacy_wireless_pids).                                           |
+\*-------------------------------------------------------------------------------------------------------------------------------------*/
+REGISTER_HID_DETECTOR_BPU("Logitech HID++ 2.0", DetectLogitechHIDPP20, LOGITECH_VID, HID_PID_ANY, HID_API_BUS_USB,       0xFF00, 2);
+REGISTER_HID_DETECTOR_BP ("Logitech HID++ 2.0", DetectLogitechHIDPP20, LOGITECH_VID, HID_PID_ANY, HID_API_BUS_USB,       0xFF43);
+REGISTER_HID_DETECTOR_IP ("Logitech HID++ 2.0", DetectLogitechHIDPP20, LOGITECH_VID, HID_PID_ANY, 1,                     0xFF00);
+REGISTER_HID_DETECTOR_BPU("Logitech HID++ 2.0", DetectLogitechHIDPP20, LOGITECH_VID, HID_PID_ANY, HID_API_BUS_USB,       0xFFA0, 1);
+REGISTER_HID_DETECTOR_BP ("Logitech HID++ 2.0", DetectLogitechHIDPP20, LOGITECH_VID, HID_PID_ANY, HID_API_BUS_BLUETOOTH, 0xFF43);
+REGISTER_HID_DETECTOR_BPU("Logitech HID++ 2.0", DetectLogitechHIDPP20, LOGITECH_VID, HID_PID_ANY, HID_API_BUS_BLUETOOTH, 0xFF00, 2);

Controllers/LogitechController/LogitechG810Controller/LogitechG810Controller.cpp

@@ -1,198 +0,0 @@
-/*---------------------------------------------------------*\
-| LogitechG810Controller.cpp                                |
-|                                                           |
-|   Driver for Logitech G810 Orion Spectrum                 |
-|                                                           |
-|   Adam Honse (CalcProgrammer1)                11 Jun 2020 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include <cstring>
-#include "LogitechG810Controller.h"
-#include "StringUtils.h"
-
-LogitechG810Controller::LogitechG810Controller(hid_device* dev_handle_0x11, hid_device* dev_handle_0x12, char* path, std::string dev_name)
-{
-    dev_pkt_0x11    = dev_handle_0x11;
-    dev_pkt_0x12    = dev_handle_0x12;
-    location        = path;
-    name            = dev_name;
-}
-
-LogitechG810Controller::~LogitechG810Controller()
-{
-    hid_close(dev_pkt_0x11);
-    hid_close(dev_pkt_0x12);
-}
-
-std::string LogitechG810Controller::GetLocationString()
-{
-    return("HID: " + location);
-}
-
-std::string LogitechG810Controller::GetNameString()
-{
-    return(name);
-}
-
-std::string LogitechG810Controller::GetSerialString()
-{
-    wchar_t serial_string[128];
-    int ret = hid_get_serial_number_string(dev_pkt_0x11, serial_string, 128);
-
-    if(ret != 0)
-    {
-        return("");
-    }
-
-    return(StringUtils::wstring_to_string(serial_string));
-}
-
-void LogitechG810Controller::Commit()
-{
-    SendCommit();
-}
-
-void LogitechG810Controller::SetDirect
-    (
-    unsigned char       zone,
-    unsigned char       frame_count,
-    unsigned char *     frame_data
-    )
-{
-    SendDirectFrame(zone, frame_count, frame_data);
-}
-
-void LogitechG810Controller::SetMode
-    (
-    unsigned char       mode,
-    unsigned short      speed,
-    unsigned char       red,
-    unsigned char       green,
-    unsigned char       blue
-    )
-{
-    SendMode(LOGITECH_G810_ZONE_MODE_KEYBOARD, mode, speed, red, green, blue);
-    SendMode(LOGITECH_G810_ZONE_MODE_LOGO,     mode, speed, red, green, blue);
-
-    SendCommit();
-}
-
-/*-------------------------------------------------------------------------------------------------*\
-| Private packet sending functions.                                                                 |
-\*-------------------------------------------------------------------------------------------------*/
-
-void LogitechG810Controller::SendCommit()
-{
-    unsigned char usb_buf[20];
-
-    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
-    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up Commit packet                                  |
-    \*-----------------------------------------------------*/
-    usb_buf[0x00]           = 0x11;
-    usb_buf[0x01]           = 0xFF;
-    usb_buf[0x02]           = 0x0C;
-    usb_buf[0x03]           = 0x5D;
-
-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    hid_write(dev_pkt_0x11, usb_buf, 20);
-    hid_read(dev_pkt_0x11, usb_buf, 20);
-}
-
-void LogitechG810Controller::SendDirectFrame
-    (
-    unsigned char       zone,
-    unsigned char       frame_count,
-    unsigned char *     frame_data
-    )
-{
-    unsigned char usb_buf[64];
-
-    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
-    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up Lighting Control packet                        |
-    \*-----------------------------------------------------*/
-    usb_buf[0x00]           = 0x12;
-    usb_buf[0x01]           = 0xFF;
-    usb_buf[0x02]           = 0x0C;
-    usb_buf[0x03]           = 0x3D;
-    usb_buf[0x05]           = zone;
-    usb_buf[0x07]           = frame_count;
-
-    /*-----------------------------------------------------*\
-    | Copy in frame data                                    |
-    \*-----------------------------------------------------*/
-    memcpy(&usb_buf[0x08], frame_data, frame_count * 4);
-
-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    hid_write(dev_pkt_0x12, usb_buf, 64);
-    hid_read(dev_pkt_0x11, usb_buf, 20);
-}
-
-void LogitechG810Controller::SendMode
-    (
-    unsigned char       zone,
-    unsigned char       mode,
-    unsigned short      speed,
-    unsigned char       red,
-    unsigned char       green,
-    unsigned char       blue
-    )
-{
-    unsigned char usb_buf[20];
-
-    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
-    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up Lighting Control packet                        |
-    \*-----------------------------------------------------*/
-    usb_buf[0x00]           = 0x11;
-    usb_buf[0x01]           = 0xFF;
-    usb_buf[0x02]           = 0x0D;
-    usb_buf[0x03]           = 0x3D;
-    usb_buf[0x04]           = zone;
-
-    usb_buf[0x05]           = mode;
-
-    usb_buf[0x06]           = red;
-    usb_buf[0x07]           = green;
-    usb_buf[0x08]           = blue;
-
-    speed = 100 * speed;
-    if(mode == LOGITECH_G810_MODE_CYCLE)
-    {
-        usb_buf[0x0B]       = speed >> 8;
-        usb_buf[0x0C]       = speed & 0xFF;
-        usb_buf[0x0D]       = 0x64;
-    }
-    else if(mode == LOGITECH_G810_MODE_BREATHING)
-    {
-        usb_buf[0x09]       = speed >> 8;
-        usb_buf[0x0A]       = speed & 0xFF;
-        usb_buf[0x0C]       = 0x64;
-    }
-
-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    hid_write(dev_pkt_0x11, usb_buf, 20);
-    hid_read(dev_pkt_0x11, usb_buf, 20);
-}

Controllers/LogitechController/LogitechG810Controller/LogitechG810Controller.h

@@ -1,104 +0,0 @@
-/*---------------------------------------------------------*\
-| LogitechG810Controller.h                                  |
-|                                                           |
-|   Driver for Logitech G810 Orion Spectrum                 |
-|                                                           |
-|   Adam Honse (CalcProgrammer1)                11 Jun 2020 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#pragma once
-
-#include <string>
-#include <hidapi.h>
-#include "RGBController.h"
-
-enum
-{
-    LOGITECH_G810_ZONE_MODE_KEYBOARD     = 0x00,
-    LOGITECH_G810_ZONE_MODE_LOGO         = 0x01,
-};
-
-enum
-{
-    LOGITECH_G810_ZONE_DIRECT_KEYBOARD   = 0x01,
-    LOGITECH_G810_ZONE_DIRECT_MEDIA      = 0x02,
-    LOGITECH_G810_ZONE_DIRECT_LOGO       = 0x10,
-    LOGITECH_G810_ZONE_DIRECT_INDICATORS = 0x40,
-};
-
-enum
-{
-    LOGITECH_G810_MODE_OFF               = 0x00,
-    LOGITECH_G810_MODE_STATIC            = 0x01,
-    LOGITECH_G810_MODE_BREATHING         = 0x02,
-    LOGITECH_G810_MODE_CYCLE             = 0x03,
-    LOGITECH_G810_MODE_WAVE              = 0x04,
-};
-
-/*---------------------------------------------------------------------------------------------*\
-| Speed is 1000 for fast and 20000 for slow.                                                    |
-| Values are multiplied by 100 later to give lots of GUI steps.                                 |
-\*---------------------------------------------------------------------------------------------*/
-enum
-{
-    LOGITECH_G810_SPEED_SLOWEST          = 0xC8,     /* Slowest speed                       */
-    LOGITECH_G810_SPEED_NORMAL           = 0x32,     /* Normal speed                        */
-    LOGITECH_G810_SPEED_FASTEST          = 0x0A,     /* Fastest speed                       */
-};
-
-class LogitechG810Controller
-{
-public:
-    LogitechG810Controller(hid_device* dev_handle_0x11, hid_device* dev_handle_0x12, char* path, std::string dev_name);
-    ~LogitechG810Controller();
-
-    std::string GetLocationString();
-    std::string GetNameString();
-    std::string GetSerialString();
-
-    void        Commit();
-
-    void        SetDirect
-                    (
-                    unsigned char       zone,
-                    unsigned char       frame_count,
-                    unsigned char *     frame_data
-                    );
-
-    void        SetMode
-                    (
-                    unsigned char       mode,
-                    unsigned short      speed,
-                    unsigned char       red,
-                    unsigned char       green,
-                    unsigned char       blue
-                    );
-
-private:
-    hid_device* dev_pkt_0x11;
-    hid_device* dev_pkt_0x12;
-    std::string location;
-    std::string name;
-
-    void        SendDirectFrame
-                    (
-                    unsigned char       zone,
-                    unsigned char       frame_count,
-                    unsigned char *     frame_data
-                    );
-
-    void        SendMode
-                    (
-                    unsigned char       zone,
-                    unsigned char       mode,
-                    unsigned short      speed,
-                    unsigned char       red,
-                    unsigned char       green,
-                    unsigned char       blue
-                    );
-
-    void        SendCommit();
-};

Controllers/LogitechController/LogitechG810Controller/RGBController_LogitechG810.cpp

@@ -1,380 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_LogitechG810.cpp                            |
-|                                                           |
-|   RGBController for Logitech G810 Orion Spectrum          |
-|                                                           |
-|   Adam Honse (CalcProgrammer1)                12 Jun 2020 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include "RGBControllerKeyNames.h"
-#include "RGBController_LogitechG810.h"
-
-//0xFFFFFFFF indicates an unused entry in matrix
-#define NA  0xFFFFFFFF
-
-static unsigned int matrix_map[7][23] =
-    { { 111,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA, 116, 114, 115,  NA, 113,  NA, 112, 110,  NA,  NA,  NA },
-      {  37,  NA,  54,  55,  56,  57,  NA,  58,  59,  60,  61,  NA,  62,  63,  64,  65,  66,  67,  68, 109, 108, 107, 106 },
-      {  49,  26,  27,  28,  29,  30,  31,  32,  33,  34,  35,  NA,  41,  42,  38,  NA,  69,  70,  71,  79,  80,  81,  82 },
-      {  39,  NA,  16,  22,   4,  17,  NA,  19,  24,  20,   8,  14,  15,  43,  44,  45,  72,  73,  74,  91,  92,  93,  83 },
-      {  53,  NA,   0,  18,   3,   5,  NA,   6,   7,   9,  10,  11,  47,  48,  46,  36,  NA,  NA,  NA,  88,  89,  90,  NA },
-      {  99,  96,  25,  23,   2,  21,  NA,   1,  NA,  13,  12,  50,  51,  52, 103,  NA,  NA,  78,  NA,  85,  86,  87,  84 },
-      {  98, 101, 100,  NA,  NA,  NA,  NA,  40,  NA,  NA,  NA,  NA, 104, 105,  97, 102,  76,  77,  75,  94,  NA,  95,  NA } };
-
-static const char* zone_names[] =
-{
-    ZONE_EN_KEYBOARD,
-};
-
-static zone_type zone_types[] =
-{
-    ZONE_TYPE_MATRIX,
-};
-
-static const unsigned int zone_sizes[] =
-{
-    117,
-};
-
-typedef struct
-{
-    const char *        name;
-    const unsigned char zone;
-    const unsigned char idx;
-} led_type;
-
-static const led_type led_names[] =
-{
-    /* Key Label                Zone,                                   Index  */
-    { KEY_EN_A,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x04    },
-    { KEY_EN_B,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x05    },
-    { KEY_EN_C,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x06    },
-    { KEY_EN_D,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x07    },
-    { KEY_EN_E,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x08    },
-    { KEY_EN_F,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x09    },
-    { KEY_EN_G,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x0A    },
-    { KEY_EN_H,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x0B    },
-    { KEY_EN_I,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x0C    },
-    { KEY_EN_J,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x0D    },
-    { KEY_EN_K,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x0E    },
-    { KEY_EN_L,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x0F    },
-    { KEY_EN_M,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x10    },
-    { KEY_EN_N,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x11    },
-    { KEY_EN_O,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x12    },
-    { KEY_EN_P,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x13    },
-    { KEY_EN_Q,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x14    },
-    { KEY_EN_R,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x15    },
-    { KEY_EN_S,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x16    },
-    { KEY_EN_T,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x17    },
-    { KEY_EN_U,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x18    },
-    { KEY_EN_V,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x19    },
-    { KEY_EN_W,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x1A    },
-    { KEY_EN_X,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x1B    },
-    { KEY_EN_Y,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x1C    },
-    { KEY_EN_Z,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x1D    },
-    { KEY_EN_1,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x1E    },
-    { KEY_EN_2,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x1F    },
-    { KEY_EN_3,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x20    },
-    { KEY_EN_4,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x21    },
-    { KEY_EN_5,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x22    },
-    { KEY_EN_6,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x23    },
-    { KEY_EN_7,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x24    },
-    { KEY_EN_8,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x25    },
-    { KEY_EN_9,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x26    },
-    { KEY_EN_0,                 LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x27    },
-    { KEY_EN_ANSI_ENTER,        LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x28    },
-    { KEY_EN_ESCAPE,            LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x29    },
-    { KEY_EN_BACKSPACE,         LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x2A    },
-    { KEY_EN_TAB,               LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x2B    },
-    { KEY_EN_SPACE,             LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x2C    },
-    { KEY_EN_MINUS,             LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x2D    },
-    { KEY_EN_EQUALS,            LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x2E    },
-    { KEY_EN_LEFT_BRACKET,      LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x2F    },
-    { KEY_EN_RIGHT_BRACKET,     LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x30    },
-    { KEY_EN_ANSI_BACK_SLASH,   LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x31    },//ANSI only
-    { KEY_EN_POUND,             LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x32    },//ISO only
-    { KEY_EN_SEMICOLON,         LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x33    },
-    { KEY_EN_QUOTE,             LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x34    },
-    { KEY_EN_BACK_TICK,         LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x35    },
-    { KEY_EN_COMMA,             LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x36    },
-    { KEY_EN_PERIOD,            LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x37    },
-    { KEY_EN_FORWARD_SLASH,     LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x38    },
-    { KEY_EN_CAPS_LOCK,         LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x39    },
-    { KEY_EN_F1,                LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x3A    },
-    { KEY_EN_F2,                LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x3B    },
-    { KEY_EN_F3,                LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x3C    },
-    { KEY_EN_F4,                LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x3D    },
-    { KEY_EN_F5,                LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x3E    },
-    { KEY_EN_F6,                LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x3F    },
-    { KEY_EN_F7,                LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x40    },
-    { KEY_EN_F8,                LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x41    },
-    { KEY_EN_F9,                LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x42    },
-    { KEY_EN_F10,               LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x43    },
-    { KEY_EN_F11,               LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x44    },
-    { KEY_EN_F12,               LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x45    },
-    { KEY_EN_PRINT_SCREEN,      LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x46    },
-    { KEY_EN_SCROLL_LOCK,       LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x47    },
-    { KEY_EN_PAUSE_BREAK,       LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x48    },
-    { KEY_EN_INSERT,            LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x49    },
-    { KEY_EN_HOME,              LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x4A    },
-    { KEY_EN_PAGE_UP,           LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x4B    },
-    { KEY_EN_DELETE,            LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x4C    },
-    { KEY_EN_END,               LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x4D    },
-    { KEY_EN_PAGE_DOWN,         LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x4E    },
-    { KEY_EN_RIGHT_ARROW,       LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x4F    },
-    { KEY_EN_LEFT_ARROW,        LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x50    },
-    { KEY_EN_DOWN_ARROW,        LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x51    },
-    { KEY_EN_UP_ARROW,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x52    },
-    { KEY_EN_NUMPAD_LOCK,       LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x53    },
-    { KEY_EN_NUMPAD_DIVIDE,     LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x54    },
-    { KEY_EN_NUMPAD_TIMES,      LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x55    },
-    { KEY_EN_NUMPAD_MINUS,      LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x56    },
-    { KEY_EN_NUMPAD_PLUS,       LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x57    },
-    { KEY_EN_NUMPAD_ENTER,      LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x58    },
-    { KEY_EN_NUMPAD_1,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x59    },
-    { KEY_EN_NUMPAD_2,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x5A    },
-    { KEY_EN_NUMPAD_3,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x5B    },
-    { KEY_EN_NUMPAD_4,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x5C    },
-    { KEY_EN_NUMPAD_5,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x5D    },
-    { KEY_EN_NUMPAD_6,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x5E    },
-    { KEY_EN_NUMPAD_7,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x5F    },
-    { KEY_EN_NUMPAD_8,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x60    },
-    { KEY_EN_NUMPAD_9,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x61    },
-    { KEY_EN_NUMPAD_0,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x62    },
-    { KEY_EN_NUMPAD_PERIOD,     LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x63    },
-    { KEY_EN_ISO_BACK_SLASH,    LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x64    },//ISO only
-    { KEY_EN_MENU,              LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0x65    },
-    { KEY_EN_LEFT_CONTROL,      LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0xE0    },
-    { KEY_EN_LEFT_SHIFT,        LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0xE1    },
-    { KEY_EN_LEFT_ALT,          LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0xE2    },
-    { KEY_EN_LEFT_WINDOWS,      LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0xE3    },
-    { KEY_EN_RIGHT_CONTROL,     LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0xE4    },
-    { KEY_EN_RIGHT_SHIFT,       LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0xE5    },
-    { KEY_EN_RIGHT_ALT,         LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0xE6    },
-    { KEY_EN_RIGHT_WINDOWS,     LOGITECH_G810_ZONE_DIRECT_KEYBOARD,     0xE7    },
-    { KEY_EN_MEDIA_NEXT,        LOGITECH_G810_ZONE_DIRECT_MEDIA,        0xB5    },
-    { KEY_EN_MEDIA_PREVIOUS,    LOGITECH_G810_ZONE_DIRECT_MEDIA,        0xB6    },
-    { KEY_EN_MEDIA_STOP,        LOGITECH_G810_ZONE_DIRECT_MEDIA,        0xB7    },
-    { KEY_EN_MEDIA_PLAY_PAUSE,  LOGITECH_G810_ZONE_DIRECT_MEDIA,        0xCD    },
-    { KEY_EN_MEDIA_MUTE,        LOGITECH_G810_ZONE_DIRECT_MEDIA,        0xE2    },
-    { "Logo",                   LOGITECH_G810_ZONE_DIRECT_LOGO,         0x01    },
-    { "Lighting",               LOGITECH_G810_ZONE_DIRECT_INDICATORS,   0x01    },
-    { "Game Mode",              LOGITECH_G810_ZONE_DIRECT_INDICATORS,   0x02    },
-    { "Caps Lock Indicator",    LOGITECH_G810_ZONE_DIRECT_INDICATORS,   0x03    },
-    { "Scroll Lock Indicator",  LOGITECH_G810_ZONE_DIRECT_INDICATORS,   0x04    },
-    { "Num Lock Indicator",     LOGITECH_G810_ZONE_DIRECT_INDICATORS,   0x05    },
-};
-
-/**------------------------------------------------------------------*\
-    @name Logitech G810
-    @category Keyboard
-    @type USB
-    @save :robot:
-    @direct :white_check_mark:
-    @effects :white_check_mark:
-    @detectors DetectLogitechKeyboardG810
-    @comment
-\*-------------------------------------------------------------------*/
-
-RGBController_LogitechG810::RGBController_LogitechG810(LogitechG810Controller* controller_ptr)
-{
-    controller                      = controller_ptr;
-
-    name                            = controller->GetNameString();
-    vendor                          = "Logitech";
-    type                            = DEVICE_TYPE_KEYBOARD;
-    description                     = "Logitech Keyboard Device";
-    location                        = controller->GetLocationString();
-    serial                          = controller->GetSerialString();
-
-    mode Direct;
-    Direct.name                     = "Direct";
-    Direct.value                    = 0xFFFF;
-    Direct.flags                    = MODE_FLAG_HAS_PER_LED_COLOR;
-    Direct.color_mode               = MODE_COLORS_PER_LED;
-    modes.push_back(Direct);
-
-    mode Static;
-    Static.name                     = "Static";
-    Static.value                    = LOGITECH_G810_MODE_STATIC;
-    Static.flags                    = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR;
-    Static.colors_min               = 1;
-    Static.colors_max               = 1;
-    Static.color_mode               = MODE_COLORS_MODE_SPECIFIC;
-    Static.colors.resize(1);
-    modes.push_back(Static);
-
-    mode Off;
-    Off.name                        = "Off";
-    Off.value                       = LOGITECH_G810_MODE_OFF;
-    Off.flags                       = 0;
-    Off.color_mode                  = MODE_COLORS_NONE;
-    modes.push_back(Off);
-
-    mode Cycle;
-    Cycle.name                      = "Cycle";
-    Cycle.value                     = LOGITECH_G810_MODE_CYCLE;
-    Cycle.flags                     = MODE_FLAG_HAS_SPEED;
-    Cycle.color_mode                = MODE_COLORS_NONE;
-    Cycle.speed_min                 = LOGITECH_G810_SPEED_SLOWEST;
-    Cycle.speed_max                 = LOGITECH_G810_SPEED_FASTEST;
-    Cycle.speed                     = LOGITECH_G810_SPEED_NORMAL;
-    modes.push_back(Cycle);
-
-    mode Breathing;
-    Breathing.name                  = "Breathing";
-    Breathing.value                 = LOGITECH_G810_MODE_BREATHING;
-    Breathing.flags                 = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR | MODE_FLAG_HAS_SPEED;
-    Breathing.colors_min            = 1;
-    Breathing.colors_max            = 1;
-    Breathing.color_mode            = MODE_COLORS_MODE_SPECIFIC;
-    Breathing.colors.resize(1);
-    Breathing.speed_min             = LOGITECH_G810_SPEED_SLOWEST;
-    Breathing.speed_max             = LOGITECH_G810_SPEED_FASTEST;
-    Breathing.speed                 = LOGITECH_G810_SPEED_NORMAL;
-    modes.push_back(Breathing);
-
-    SetupZones();
-}
-
-RGBController_LogitechG810::~RGBController_LogitechG810()
-{
-    Shutdown();
-
-    delete controller;
-}
-
-void RGBController_LogitechG810::SetupZones()
-{
-    /*---------------------------------------------------------*\
-    | Set up zones                                              |
-    \*---------------------------------------------------------*/
-    unsigned int total_led_count = 0;
-    for(unsigned int zone_idx = 0; zone_idx < 1; zone_idx++)
-    {
-        zone new_zone;
-        new_zone.name                   = zone_names[zone_idx];
-        new_zone.type                   = zone_types[zone_idx];
-        new_zone.leds_min               = zone_sizes[zone_idx];
-        new_zone.leds_max               = zone_sizes[zone_idx];
-        new_zone.leds_count             = zone_sizes[zone_idx];
-
-        if(zone_types[zone_idx] == ZONE_TYPE_MATRIX)
-        {
-            new_zone.matrix_map.Set(7, 23, (unsigned int *)&matrix_map);
-        }
-
-        zones.push_back(new_zone);
-
-        total_led_count += zone_sizes[zone_idx];
-    }
-
-    for(unsigned int led_idx = 0; led_idx < total_led_count; led_idx++)
-    {
-        led new_led;
-        new_led.name                    = led_names[led_idx].name;
-        new_led.value                   = ( led_names[led_idx].zone << 8 ) + led_names[led_idx].idx;
-        leds.push_back(new_led);
-    }
-
-    SetupColors();
-}
-
-void RGBController_LogitechG810::DeviceUpdateLEDs()
-{
-    #define MAX_FRAMES_PER_PACKET 0x0E
-
-    unsigned char frame_buf[MAX_FRAMES_PER_PACKET * 4];
-    unsigned char frame_cnt = 0;
-    unsigned char prev_zone = 0;
-    unsigned char zone      = 0;
-    unsigned char idx       = 0;
-
-    /*---------------------------------------------------------*\
-    | TODO: Send packets with multiple LED frames               |
-    \*---------------------------------------------------------*/
-    for(std::size_t led_idx = 0; led_idx < leds.size(); led_idx++)
-    {
-        zone = ( leds[led_idx].value >> 8 );
-        idx  = ( leds[led_idx].value & 0xFF );
-
-        if((zone != prev_zone) && (frame_cnt != 0))
-        {
-            controller->SetDirect(prev_zone, frame_cnt, frame_buf);
-            frame_cnt = 0;
-        }
-
-        frame_buf[(frame_cnt * 4) + 0] = idx;
-        frame_buf[(frame_cnt * 4) + 1] = RGBGetRValue(colors[led_idx]);
-        frame_buf[(frame_cnt * 4) + 2] = RGBGetGValue(colors[led_idx]);
-        frame_buf[(frame_cnt * 4) + 3] = RGBGetBValue(colors[led_idx]);
-
-        frame_cnt++;
-        prev_zone = zone;
-
-        if(frame_cnt == MAX_FRAMES_PER_PACKET)
-        {
-            controller->SetDirect(prev_zone, frame_cnt, frame_buf);
-            frame_cnt = 0;
-        }
-    }
-
-    if(frame_cnt != 0)
-    {
-        controller->SetDirect(prev_zone, frame_cnt, frame_buf);
-    }
-
-    controller->Commit();
-}
-
-void RGBController_LogitechG810::DeviceUpdateZoneLEDs(int /*zone*/)
-{
-    DeviceUpdateLEDs();
-}
-
-void RGBController_LogitechG810::DeviceUpdateSingleLED(int led)
-{
-    unsigned char frame[4];
-    unsigned char zone;
-    unsigned char idx;
-
-    zone = ( leds[led].value >> 8 );
-    idx  = ( leds[led].value & 0xFF );
-
-    frame[0] = idx;
-    frame[1] = RGBGetRValue(colors[led]);
-    frame[2] = RGBGetGValue(colors[led]);
-    frame[3] = RGBGetBValue(colors[led]);
-
-    controller->SetDirect(zone, 1, frame);
-    controller->Commit();
-}
-
-void RGBController_LogitechG810::DeviceUpdateMode()
-{
-    /*---------------------------------------------------------*\
-    | Direct mode does not send a mode packet                   |
-    | Call UpdateLEDs to send direct packet                     |
-    \*---------------------------------------------------------*/
-    if(active_mode == 0xFFFF)
-    {
-        UpdateLEDsInternal();
-        return;
-    }
-
-    unsigned char red = 0;
-    unsigned char grn = 0;
-    unsigned char blu = 0;
-
-    if(modes[active_mode].color_mode == MODE_COLORS_MODE_SPECIFIC)
-    {
-        red = RGBGetRValue(modes[active_mode].colors[0]);
-        grn = RGBGetGValue(modes[active_mode].colors[0]);
-        blu = RGBGetBValue(modes[active_mode].colors[0]);
-    }
-
-    controller->SetMode(modes[active_mode].value, modes[active_mode].speed, red, grn, blu);
-}

Controllers/LogitechController/LogitechG810Controller/RGBController_LogitechG810.h

@@ -1,33 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_LogitechG810.h                              |
-|                                                           |
-|   RGBController for Logitech G810 Orion Spectrum          |
-|                                                           |
-|   Adam Honse (CalcProgrammer1)                12 Jun 2020 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#pragma once
-
-#include "RGBController.h"
-#include "LogitechG810Controller.h"
-
-class RGBController_LogitechG810 : public RGBController
-{
-public:
-    RGBController_LogitechG810(LogitechG810Controller* controller_ptr);
-    ~RGBController_LogitechG810();
-
-    void        SetupZones();
-
-    void        DeviceUpdateLEDs();
-    void        DeviceUpdateZoneLEDs(int zone);
-    void        DeviceUpdateSingleLED(int led);
-
-    void        DeviceUpdateMode();
-
-private:
-    LogitechG810Controller* controller;
-};

Controllers/LogitechController/LogitechG910Controller/LogitechG910Controller.cpp

@@ -1,198 +0,0 @@
-/*---------------------------------------------------------*\
-| LogitechG910Controller.cpp                                |
-|                                                           |
-|   Driver for Logitech G910 Orion Spectrum                 |
-|                                                           |
-|   Adam Honse (CalcProgrammer1)                11 Jun 2020 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include <cstring>
-#include "LogitechG910Controller.h"
-#include "StringUtils.h"
-
-LogitechG910Controller::LogitechG910Controller(hid_device* dev_handle_0x11, hid_device* dev_handle_0x12, char* path, std::string dev_name)
-{
-    dev_pkt_0x11    = dev_handle_0x11;
-    dev_pkt_0x12    = dev_handle_0x12;
-    location        = path;
-    name            = dev_name;
-}
-
-LogitechG910Controller::~LogitechG910Controller()
-{
-    hid_close(dev_pkt_0x11);
-    hid_close(dev_pkt_0x12);
-}
-
-std::string LogitechG910Controller::GetNameString()
-{
-    return(name);
-}
-
-std::string LogitechG910Controller::GetLocationString()
-{
-    return("HID: " + location);
-}
-
-std::string LogitechG910Controller::GetSerialString()
-{
-    wchar_t serial_string[128];
-    int ret = hid_get_serial_number_string(dev_pkt_0x11, serial_string, 128);
-
-    if(ret != 0)
-    {
-        return("");
-    }
-
-    return(StringUtils::wstring_to_string(serial_string));
-}
-
-void LogitechG910Controller::Commit()
-{
-    SendCommit();
-}
-
-void LogitechG910Controller::SetDirect
-    (
-    unsigned char       zone,
-    unsigned char       frame_count,
-    unsigned char *     frame_data
-    )
-{
-    SendDirectFrame(zone, frame_count, frame_data);
-}
-
-void LogitechG910Controller::SetMode
-    (
-    unsigned char       mode,
-    unsigned short      speed,
-    unsigned char       red,
-    unsigned char       green,
-    unsigned char       blue
-    )
-{
-    SendMode(LOGITECH_G910_ZONE_MODE_KEYBOARD, mode, speed, red, green, blue);
-    SendMode(LOGITECH_G910_ZONE_MODE_LOGO,     mode, speed, red, green, blue);
-
-    SendCommit();
-}
-
-/*-------------------------------------------------------------------------------------------------*\
-| Private packet sending functions.                                                                 |
-\*-------------------------------------------------------------------------------------------------*/
-
-void LogitechG910Controller::SendCommit()
-{
-    unsigned char usb_buf[20];
-
-    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
-    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up Commit packet                                  |
-    \*-----------------------------------------------------*/
-    usb_buf[0x00]           = 0x11;
-    usb_buf[0x01]           = 0xFF;
-    usb_buf[0x02]           = 0x0F;
-    usb_buf[0x03]           = 0x5F;
-
-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    hid_write(dev_pkt_0x11, usb_buf, 20);
-    hid_read(dev_pkt_0x11, usb_buf, 20);
-}
-
-void LogitechG910Controller::SendDirectFrame
-    (
-    unsigned char       zone,
-    unsigned char       frame_count,
-    unsigned char *     frame_data
-    )
-{
-    unsigned char usb_buf[64];
-
-    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
-    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up Lighting Control packet                        |
-    \*-----------------------------------------------------*/
-    usb_buf[0x00]           = 0x12;
-    usb_buf[0x01]           = 0xFF;
-    usb_buf[0x02]           = 0x0F;
-    usb_buf[0x03]           = 0x3F;
-    usb_buf[0x05]           = zone;
-    usb_buf[0x07]           = frame_count;
-
-    /*-----------------------------------------------------*\
-    | Copy in frame data                                    |
-    \*-----------------------------------------------------*/
-    memcpy(&usb_buf[0x08], frame_data, frame_count * 4);
-
-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    hid_write(dev_pkt_0x12, usb_buf, 64);
-    hid_read(dev_pkt_0x11, usb_buf, 20);
-}
-
-void LogitechG910Controller::SendMode
-    (
-    unsigned char       zone,
-    unsigned char       mode,
-    unsigned short      speed,
-    unsigned char       red,
-    unsigned char       green,
-    unsigned char       blue
-    )
-{
-    unsigned char usb_buf[20];
-
-    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
-    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up Lighting Control packet                        |
-    \*-----------------------------------------------------*/
-    usb_buf[0x00]           = 0x11;
-    usb_buf[0x01]           = 0xFF;
-    usb_buf[0x02]           = 0x10;
-    usb_buf[0x03]           = 0x3B;
-    usb_buf[0x04]           = zone;
-
-    usb_buf[0x05]           = mode;
-
-    usb_buf[0x06]           = red;
-    usb_buf[0x07]           = green;
-    usb_buf[0x08]           = blue;
-
-    speed = 100 * speed;
-    if(mode == LOGITECH_G910_MODE_CYCLE)
-    {
-        usb_buf[0x0B]       = speed >> 8;
-        usb_buf[0x0C]       = speed & 0xFF;
-        usb_buf[0x0D]       = 0x64;
-    }
-    else if(mode == LOGITECH_G910_MODE_BREATHING)
-    {
-        usb_buf[0x09]       = speed >> 8;
-        usb_buf[0x0A]       = speed & 0xFF;
-        usb_buf[0x0C]       = 0x64;
-    }
-
-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    hid_write(dev_pkt_0x11, usb_buf, 20);
-    hid_read(dev_pkt_0x11, usb_buf, 20);
-}

Controllers/LogitechController/LogitechG910Controller/LogitechG910Controller.h

@@ -1,104 +0,0 @@
-/*---------------------------------------------------------*\
-| LogitechG910Controller.h                                  |
-|                                                           |
-|   Driver for Logitech G910 Orion Spectrum                 |
-|                                                           |
-|   Adam Honse (CalcProgrammer1)                11 Jun 2020 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#pragma once
-
-#include <string>
-#include <hidapi.h>
-#include "RGBController.h"
-
-enum
-{
-    LOGITECH_G910_ZONE_MODE_KEYBOARD     = 0x00,
-    LOGITECH_G910_ZONE_MODE_LOGO         = 0x01,
-};
-
-enum
-{
-    LOGITECH_G910_ZONE_DIRECT_KEYBOARD   = 0x01,
-    LOGITECH_G910_ZONE_DIRECT_GKEYS      = 0x04,
-    LOGITECH_G910_ZONE_DIRECT_LOGO       = 0x10,
-    LOGITECH_G910_ZONE_DIRECT_INDICATORS = 0x40,
-};
-
-enum
-{
-    LOGITECH_G910_MODE_OFF               = 0x00,
-    LOGITECH_G910_MODE_STATIC            = 0x01,
-    LOGITECH_G910_MODE_BREATHING         = 0x02,
-    LOGITECH_G910_MODE_CYCLE             = 0x03,
-    LOGITECH_G910_MODE_WAVE              = 0x04,
-};
-
-/*---------------------------------------------------------------------------------------------*\
-| Speed is 1000 for fast and 20000 for slow.                                                    |
-| Values are multiplied by 100 later to give lots of GUI steps.                                 |
-\*---------------------------------------------------------------------------------------------*/
-enum
-{
-    LOGITECH_G910_SPEED_SLOWEST          = 0xC8,     /* Slowest speed                       */
-    LOGITECH_G910_SPEED_NORMAL           = 0x32,     /* Normal speed                        */
-    LOGITECH_G910_SPEED_FASTEST          = 0x0A,     /* Fastest speed                       */
-};
-
-class LogitechG910Controller
-{
-public:
-    LogitechG910Controller(hid_device* dev_handle_0x11, hid_device* dev_handle_0x12, char* path, std::string dev_name);
-    ~LogitechG910Controller();
-
-    std::string GetLocationString();
-    std::string GetNameString();
-    std::string GetSerialString();
-
-    void        Commit();
-
-    void        SetDirect
-                    (
-                    unsigned char       zone,
-                    unsigned char       frame_count,
-                    unsigned char *     frame_data
-                    );
-
-    void        SetMode
-                    (
-                    unsigned char       mode,
-                    unsigned short      speed,
-                    unsigned char       red,
-                    unsigned char       green,
-                    unsigned char       blue
-                    );
-
-private:
-    hid_device* dev_pkt_0x11;
-    hid_device* dev_pkt_0x12;
-    std::string location;
-    std::string name;
-
-    void        SendDirectFrame
-                    (
-                    unsigned char       zone,
-                    unsigned char       frame_count,
-                    unsigned char *     frame_data
-                    );
-
-    void        SendMode
-                    (
-                    unsigned char       zone,
-                    unsigned char       mode,
-                    unsigned short      speed,
-                    unsigned char       red,
-                    unsigned char       green,
-                    unsigned char       blue
-                    );
-
-    void        SendCommit();
-};

Controllers/LogitechController/LogitechG910Controller/RGBController_LogitechG910.cpp

@@ -1,381 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_LogitechG910.cpp                            |
-|                                                           |
-|   RGBController for Logitech G910 Orion Spectrum          |
-|                                                           |
-|   Adam Honse (CalcProgrammer1)                12 Jun 2020 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include "RGBControllerKeyNames.h"
-#include "RGBController_LogitechG910.h"
-
-//0xFFFFFFFF indicates an unused entry in matrix
-#define NA  0xFFFFFFFF
-
-static unsigned int matrix_map[8][24] =
-    { {  NA, 111, 112, 113, 114,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA },
-      { 115,  37,  NA,  54,  55,  56,  57,  NA,  58,  59,  60,  61,  NA,  62,  63,  64,  65,  66,  67,  68,  NA,  NA,  NA,  NA },
-      { 106,  49,  26,  27,  28,  29,  30,  31,  32,  33,  34,  35,  NA,  41,  42,  38,  NA,  69,  70,  71,  79,  80,  81,  82 },
-      { 107,  39,  NA,  16,  22,   4,  17,  NA,  19,  24,  20,   8,  14,  15,  43,  44,  45,  72,  73,  74,  91,  92,  93,  83 },
-      { 108,  53,  NA,   0,  18,   3,   5,  NA,   6,   7,   9,  10,  11,  47,  48,  46,  36,  NA,  NA,  NA,  88,  89,  90,  NA },
-      { 109,  99,  96,  25,  23,   2,  21,  NA,   1,  NA,  13,  12,  50,  51,  52, 103,  NA,  NA,  78,  NA,  85,  86,  87,  84 },
-      { 110,  98, 101, 100,  NA,  NA,  NA,  NA,  40,  NA,  NA,  NA,  NA, 104, 105,  97, 102,  76,  77,  75,  94,  NA,  95,  NA },
-      {  NA,  NA,  NA, 116,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA } };
-
-static const char* zone_names[] =
-{
-    ZONE_EN_KEYBOARD,
-};
-
-static zone_type zone_types[] =
-{
-    ZONE_TYPE_MATRIX,
-};
-
-static const unsigned int zone_sizes[] =
-{
-    117,
-};
-
-typedef struct
-{
-    const char *        name;
-    const unsigned char zone;
-    const unsigned char idx;
-} led_type;
-
-static const led_type led_names[] =
-{
-    /* Key Label                Zone,                                   Index  */
-    { KEY_EN_A,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x04    },
-    { KEY_EN_B,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x05    },
-    { KEY_EN_C,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x06    },
-    { KEY_EN_D,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x07    },
-    { KEY_EN_E,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x08    },
-    { KEY_EN_F,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x09    },
-    { KEY_EN_G,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x0A    },
-    { KEY_EN_H,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x0B    },
-    { KEY_EN_I,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x0C    },
-    { KEY_EN_J,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x0D    },
-    { KEY_EN_K,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x0E    },
-    { KEY_EN_L,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x0F    },
-    { KEY_EN_M,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x10    },
-    { KEY_EN_N,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x11    },
-    { KEY_EN_O,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x12    },
-    { KEY_EN_P,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x13    },
-    { KEY_EN_Q,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x14    },
-    { KEY_EN_R,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x15    },
-    { KEY_EN_S,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x16    },
-    { KEY_EN_T,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x17    },
-    { KEY_EN_U,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x18    },
-    { KEY_EN_V,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x19    },
-    { KEY_EN_W,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x1A    },
-    { KEY_EN_X,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x1B    },
-    { KEY_EN_Y,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x1C    },
-    { KEY_EN_Z,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x1D    },
-    { KEY_EN_1,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x1E    },
-    { KEY_EN_2,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x1F    },
-    { KEY_EN_3,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x20    },
-    { KEY_EN_4,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x21    },
-    { KEY_EN_5,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x22    },
-    { KEY_EN_6,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x23    },
-    { KEY_EN_7,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x24    },
-    { KEY_EN_8,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x25    },
-    { KEY_EN_9,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x26    },
-    { KEY_EN_0,                 LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x27    },
-    { KEY_EN_ANSI_ENTER,        LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x28    },
-    { KEY_EN_ESCAPE,            LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x29    },
-    { KEY_EN_BACKSPACE,         LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x2A    },
-    { KEY_EN_TAB,               LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x2B    },
-    { KEY_EN_SPACE,             LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x2C    },
-    { KEY_EN_MINUS,             LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x2D    },
-    { KEY_EN_EQUALS,            LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x2E    },
-    { KEY_EN_LEFT_BRACKET,      LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x2F    },
-    { KEY_EN_RIGHT_BRACKET,     LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x30    },
-    { KEY_EN_ANSI_BACK_SLASH,   LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x31    },//ANSI only
-    { KEY_EN_POUND,             LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x32    },//ISO only
-    { KEY_EN_SEMICOLON,         LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x33    },
-    { KEY_EN_QUOTE,             LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x34    },
-    { KEY_EN_BACK_TICK,         LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x35    },
-    { KEY_EN_COMMA,             LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x36    },
-    { KEY_EN_PERIOD,            LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x37    },
-    { KEY_EN_FORWARD_SLASH,     LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x38    },
-    { KEY_EN_CAPS_LOCK,         LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x39    },
-    { KEY_EN_F1,                LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x3A    },
-    { KEY_EN_F2,                LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x3B    },
-    { KEY_EN_F3,                LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x3C    },
-    { KEY_EN_F4,                LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x3D    },
-    { KEY_EN_F5,                LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x3E    },
-    { KEY_EN_F6,                LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x3F    },
-    { KEY_EN_F7,                LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x40    },
-    { KEY_EN_F8,                LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x41    },
-    { KEY_EN_F9,                LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x42    },
-    { KEY_EN_F10,               LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x43    },
-    { KEY_EN_F11,               LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x44    },
-    { KEY_EN_F12,               LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x45    },
-    { KEY_EN_PRINT_SCREEN,      LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x46    },
-    { KEY_EN_SCROLL_LOCK,       LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x47    },
-    { KEY_EN_PAUSE_BREAK,       LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x48    },
-    { KEY_EN_INSERT,            LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x49    },
-    { KEY_EN_HOME,              LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x4A    },
-    { KEY_EN_PAGE_UP,           LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x4B    },
-    { KEY_EN_DELETE,            LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x4C    },
-    { KEY_EN_END,               LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x4D    },
-    { KEY_EN_PAGE_DOWN,         LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x4E    },
-    { KEY_EN_RIGHT_ARROW,       LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x4F    },
-    { KEY_EN_LEFT_ARROW,        LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x50    },
-    { KEY_EN_DOWN_ARROW,        LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x51    },
-    { KEY_EN_UP_ARROW,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x52    },
-    { KEY_EN_NUMPAD_LOCK,       LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x53    },
-    { KEY_EN_NUMPAD_DIVIDE,     LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x54    },
-    { KEY_EN_NUMPAD_TIMES,      LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x55    },
-    { KEY_EN_NUMPAD_MINUS,      LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x56    },
-    { KEY_EN_NUMPAD_PLUS,       LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x57    },
-    { KEY_EN_NUMPAD_ENTER,      LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x58    },
-    { KEY_EN_NUMPAD_1,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x59    },
-    { KEY_EN_NUMPAD_2,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x5A    },
-    { KEY_EN_NUMPAD_3,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x5B    },
-    { KEY_EN_NUMPAD_4,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x5C    },
-    { KEY_EN_NUMPAD_5,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x5D    },
-    { KEY_EN_NUMPAD_6,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x5E    },
-    { KEY_EN_NUMPAD_7,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x5F    },
-    { KEY_EN_NUMPAD_8,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x60    },
-    { KEY_EN_NUMPAD_9,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x61    },
-    { KEY_EN_NUMPAD_0,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x62    },
-    { KEY_EN_NUMPAD_PERIOD,     LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x63    },
-    { KEY_EN_ISO_BACK_SLASH,    LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x64    },//ISO only
-    { KEY_EN_MENU,              LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0x65    },
-    { KEY_EN_LEFT_CONTROL,      LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0xE0    },
-    { KEY_EN_LEFT_SHIFT,        LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0xE1    },
-    { KEY_EN_LEFT_ALT,          LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0xE2    },
-    { KEY_EN_LEFT_WINDOWS,      LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0xE3    },
-    { KEY_EN_RIGHT_CONTROL,     LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0xE4    },
-    { KEY_EN_RIGHT_SHIFT,       LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0xE5    },
-    { KEY_EN_RIGHT_ALT,         LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0xE6    },
-    { KEY_EN_RIGHT_WINDOWS,     LOGITECH_G910_ZONE_DIRECT_KEYBOARD,     0xE7    },
-    { "Key: G1",                LOGITECH_G910_ZONE_DIRECT_GKEYS,        0x01    },
-    { "Key: G2",                LOGITECH_G910_ZONE_DIRECT_GKEYS,        0x02    },
-    { "Key: G3",                LOGITECH_G910_ZONE_DIRECT_GKEYS,        0x03    },
-    { "Key: G4",                LOGITECH_G910_ZONE_DIRECT_GKEYS,        0x04    },
-    { "Key: G5",                LOGITECH_G910_ZONE_DIRECT_GKEYS,        0x05    },
-    { "Key: G6",                LOGITECH_G910_ZONE_DIRECT_GKEYS,        0x06    },
-    { "Key: G7",                LOGITECH_G910_ZONE_DIRECT_GKEYS,        0x07    },
-    { "Key: G8",                LOGITECH_G910_ZONE_DIRECT_GKEYS,        0x08    },
-    { "Key: G9",                LOGITECH_G910_ZONE_DIRECT_GKEYS,        0x09    },
-    { "Logo",                   LOGITECH_G910_ZONE_DIRECT_LOGO,         0x01    },
-    { "Nameplate",              LOGITECH_G910_ZONE_DIRECT_LOGO,         0x02    },
-};
-
-/**------------------------------------------------------------------*\
-    @name Logitech G910
-    @category Keyboard
-    @type USB
-    @save :robot:
-    @direct :white_check_mark:
-    @effects :white_check_mark:
-    @detectors DetectLogitechKeyboardG910
-    @comment
-\*-------------------------------------------------------------------*/
-
-RGBController_LogitechG910::RGBController_LogitechG910(LogitechG910Controller* controller_ptr)
-{
-    controller                      = controller_ptr;
-
-    name                            = controller->GetNameString();
-    vendor                          = "Logitech";
-    type                            = DEVICE_TYPE_KEYBOARD;
-    description                     = "Logitech Keyboard Device";
-    location                        = controller->GetLocationString();
-    serial                          = controller->GetSerialString();
-
-    mode Direct;
-    Direct.name                     = "Direct";
-    Direct.value                    = 0xFFFF;
-    Direct.flags                    = MODE_FLAG_HAS_PER_LED_COLOR;
-    Direct.color_mode               = MODE_COLORS_PER_LED;
-    modes.push_back(Direct);
-
-    mode Static;
-    Static.name                     = "Static";
-    Static.value                    = LOGITECH_G910_MODE_STATIC;
-    Static.flags                    = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR;
-    Static.colors_min               = 1;
-    Static.colors_max               = 1;
-    Static.color_mode               = MODE_COLORS_MODE_SPECIFIC;
-    Static.colors.resize(1);
-    modes.push_back(Static);
-
-    mode Off;
-    Off.name                        = "Off";
-    Off.value                       = LOGITECH_G910_MODE_OFF;
-    Off.flags                       = 0;
-    Off.color_mode                  = MODE_COLORS_NONE;
-    modes.push_back(Off);
-
-    mode Cycle;
-    Cycle.name                      = "Cycle";
-    Cycle.value                     = LOGITECH_G910_MODE_CYCLE;
-    Cycle.flags                     = MODE_FLAG_HAS_SPEED;
-    Cycle.color_mode                = MODE_COLORS_NONE;
-    Cycle.speed_min                 = LOGITECH_G910_SPEED_SLOWEST;
-    Cycle.speed_max                 = LOGITECH_G910_SPEED_FASTEST;
-    Cycle.speed                     = LOGITECH_G910_SPEED_NORMAL;
-    modes.push_back(Cycle);
-
-    mode Breathing;
-    Breathing.name                  = "Breathing";
-    Breathing.value                 = LOGITECH_G910_MODE_BREATHING;
-    Breathing.flags                 = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR | MODE_FLAG_HAS_SPEED;
-    Breathing.colors_min            = 1;
-    Breathing.colors_max            = 1;
-    Breathing.color_mode            = MODE_COLORS_MODE_SPECIFIC;
-    Breathing.colors.resize(1);
-    Breathing.speed_min             = LOGITECH_G910_SPEED_SLOWEST;
-    Breathing.speed_max             = LOGITECH_G910_SPEED_FASTEST;
-    Breathing.speed                 = LOGITECH_G910_SPEED_NORMAL;
-    modes.push_back(Breathing);
-
-    SetupZones();
-}
-
-RGBController_LogitechG910::~RGBController_LogitechG910()
-{
-    Shutdown();
-
-    delete controller;
-}
-
-void RGBController_LogitechG910::SetupZones()
-{
-    /*---------------------------------------------------------*\
-    | Set up zones                                              |
-    \*---------------------------------------------------------*/
-    unsigned int total_led_count = 0;
-    for(unsigned int zone_idx = 0; zone_idx < 1; zone_idx++)
-    {
-        zone new_zone;
-        new_zone.name                   = zone_names[zone_idx];
-        new_zone.type                   = zone_types[zone_idx];
-        new_zone.leds_min               = zone_sizes[zone_idx];
-        new_zone.leds_max               = zone_sizes[zone_idx];
-        new_zone.leds_count             = zone_sizes[zone_idx];
-
-        if(zone_types[zone_idx] == ZONE_TYPE_MATRIX)
-        {
-            new_zone.matrix_map.Set(8, 24, (unsigned int *)&matrix_map);
-        }
-
-        zones.push_back(new_zone);
-
-        total_led_count += zone_sizes[zone_idx];
-    }
-
-    for(unsigned int led_idx = 0; led_idx < total_led_count; led_idx++)
-    {
-        led new_led;
-        new_led.name                    = led_names[led_idx].name;
-        new_led.value                   = ( led_names[led_idx].zone << 8 ) + led_names[led_idx].idx;
-        leds.push_back(new_led);
-    }
-
-    SetupColors();
-}
-
-void RGBController_LogitechG910::DeviceUpdateLEDs()
-{
-    #define MAX_FRAMES_PER_PACKET 0x0E
-
-    unsigned char frame_buf[MAX_FRAMES_PER_PACKET * 4];
-    unsigned char frame_cnt = 0;
-    unsigned char prev_zone = 0;
-    unsigned char zone      = 0;
-    unsigned char idx       = 0;
-
-    /*---------------------------------------------------------*\
-    | TODO: Send packets with multiple LED frames               |
-    \*---------------------------------------------------------*/
-    for(std::size_t led_idx = 0; led_idx < leds.size(); led_idx++)
-    {
-        zone = ( leds[led_idx].value >> 8 );
-        idx  = ( leds[led_idx].value & 0xFF );
-
-        if((zone != prev_zone) && (frame_cnt != 0))
-        {
-            controller->SetDirect(prev_zone, frame_cnt, frame_buf);
-            frame_cnt = 0;
-        }
-
-        frame_buf[(frame_cnt * 4) + 0] = idx;
-        frame_buf[(frame_cnt * 4) + 1] = RGBGetRValue(colors[led_idx]);
-        frame_buf[(frame_cnt * 4) + 2] = RGBGetGValue(colors[led_idx]);
-        frame_buf[(frame_cnt * 4) + 3] = RGBGetBValue(colors[led_idx]);
-
-        frame_cnt++;
-        prev_zone = zone;
-
-        if(frame_cnt == MAX_FRAMES_PER_PACKET)
-        {
-            controller->SetDirect(prev_zone, frame_cnt, frame_buf);
-            frame_cnt = 0;
-        }
-    }
-
-    if(frame_cnt != 0)
-    {
-        controller->SetDirect(prev_zone, frame_cnt, frame_buf);
-    }
-
-    controller->Commit();
-}
-
-void RGBController_LogitechG910::DeviceUpdateZoneLEDs(int /*zone*/)
-{
-    DeviceUpdateLEDs();
-}
-
-void RGBController_LogitechG910::DeviceUpdateSingleLED(int led)
-{
-    unsigned char frame[4];
-    unsigned char zone;
-    unsigned char idx;
-
-    zone = ( leds[led].value >> 8 );
-    idx  = ( leds[led].value & 0xFF );
-
-    frame[0] = idx;
-    frame[1] = RGBGetRValue(colors[led]);
-    frame[2] = RGBGetGValue(colors[led]);
-    frame[3] = RGBGetBValue(colors[led]);
-
-    controller->SetDirect(zone, 1, frame);
-    controller->Commit();
-}
-
-void RGBController_LogitechG910::DeviceUpdateMode()
-{
-    /*---------------------------------------------------------*\
-    | Direct mode does not send a mode packet                   |
-    | Call UpdateLEDs to send direct packet                     |
-    \*---------------------------------------------------------*/
-    if(active_mode == 0xFFFF)
-    {
-        UpdateLEDsInternal();
-        return;
-    }
-
-    unsigned char red = 0;
-    unsigned char grn = 0;
-    unsigned char blu = 0;
-
-    if(modes[active_mode].color_mode == MODE_COLORS_MODE_SPECIFIC)
-    {
-        red = RGBGetRValue(modes[active_mode].colors[0]);
-        grn = RGBGetGValue(modes[active_mode].colors[0]);
-        blu = RGBGetBValue(modes[active_mode].colors[0]);
-    }
-
-    controller->SetMode(modes[active_mode].value, modes[active_mode].speed, red, grn, blu);
-}

Controllers/LogitechController/LogitechG910Controller/RGBController_LogitechG910.h

@@ -1,33 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_LogitechG910.h                              |
-|                                                           |
-|   RGBController for Logitech G910 Orion Spectrum          |
-|                                                           |
-|   Adam Honse (CalcProgrammer1)                12 Jun 2020 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#pragma once
-
-#include "RGBController.h"
-#include "LogitechG910Controller.h"
-
-class RGBController_LogitechG910 : public RGBController
-{
-public:
-    RGBController_LogitechG910(LogitechG910Controller* controller_ptr);
-    ~RGBController_LogitechG910();
-
-    void        SetupZones();
-
-    void        DeviceUpdateLEDs();
-    void        DeviceUpdateZoneLEDs(int zone);
-    void        DeviceUpdateSingleLED(int led);
-
-    void        DeviceUpdateMode();
-
-private:
-    LogitechG910Controller* controller;
-};

Controllers/LogitechController/LogitechGProKeyboardController/LogitechGProKeyboardController.cpp

@@ -1,192 +0,0 @@
-/*---------------------------------------------------------*\
-| LogitechGProController.cpp                                |
-|                                                           |
-|   Driver for Logitech G Pro keyboard                      |
-|                                                           |
-|   sanchezzzs                                  20 Oct 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include <cstring>
-#include "LogitechGProKeyboardController.h"
-#include "StringUtils.h"
-
-LogitechGProKeyboardController::LogitechGProKeyboardController(hid_device* dev_handle_0x11, hid_device* dev_handle_0x12, std::string dev_name)
-{
-    dev_pkt_0x11    = dev_handle_0x11;
-    dev_pkt_0x12    = dev_handle_0x12;
-    name            = dev_name;
-}
-
-LogitechGProKeyboardController::~LogitechGProKeyboardController()
-{
-    hid_close(dev_pkt_0x11);
-    hid_close(dev_pkt_0x12);
-}
-
-std::string LogitechGProKeyboardController::GetNameString()
-{
-    return(name);
-}
-
-std::string LogitechGProKeyboardController::GetSerialString()
-{
-    wchar_t serial_string[128];
-    int ret = hid_get_serial_number_string(dev_pkt_0x11, serial_string, 128);
-
-    if(ret != 0)
-    {
-        return("");
-    }
-
-    return(StringUtils::wstring_to_string(serial_string));
-}
-
-void LogitechGProKeyboardController::Commit()
-{
-    SendCommit();
-}
-
-void LogitechGProKeyboardController::SetDirect
-    (
-    unsigned char       zone,
-    unsigned char       frame_count,
-    unsigned char *     frame_data
-    )
-{
-    SendDirectFrame(zone, frame_count, frame_data);
-}
-
-void LogitechGProKeyboardController::SetMode
-    (
-    unsigned char       mode,
-    unsigned short      speed,
-    unsigned char       red,
-    unsigned char       green,
-    unsigned char       blue
-    )
-{
-    SendMode(LOGITECH_GPRO_ZONE_MODE_KEYBOARD, mode, speed, red, green, blue);
-    SendMode(LOGITECH_GPRO_ZONE_MODE_LOGO,     mode, speed, red, green, blue);
-
-    SendCommit();
-}
-
-/*-------------------------------------------------------------------------------------------------*\
-| Private packet sending functions.                                                                 |
-\*-------------------------------------------------------------------------------------------------*/
-
-void LogitechGProKeyboardController::SendCommit()
-{
-    unsigned char usb_buf[20];
-
-    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
-    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up Commit packet                                  |
-    \*-----------------------------------------------------*/
-    usb_buf[0x00]           = 0x11;
-    usb_buf[0x01]           = 0xFF;
-    usb_buf[0x02]           = 0x0C;
-    usb_buf[0x03]           = 0x5D;
-
-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    hid_write(dev_pkt_0x11, usb_buf, 20);
-    hid_read(dev_pkt_0x11, usb_buf, 20);
-}
-
-void LogitechGProKeyboardController::SendDirectFrame
-    (
-    unsigned char       zone,
-    unsigned char       frame_count,
-    unsigned char *     frame_data
-    )
-{
-    unsigned char usb_buf[64];
-
-    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
-    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up Lighting Control packet                        |
-    \*-----------------------------------------------------*/
-    usb_buf[0x00]           = 0x12;
-    usb_buf[0x01]           = 0xFF;
-    usb_buf[0x02]           = 0x0C;
-    usb_buf[0x03]           = 0x3D;
-    usb_buf[0x05]           = zone;
-    usb_buf[0x07]           = frame_count;
-
-    /*-----------------------------------------------------*\
-    | Copy in frame data                                    |
-    \*-----------------------------------------------------*/
-    memcpy(&usb_buf[0x08], frame_data, frame_count * 4);
-
-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    hid_write(dev_pkt_0x12, usb_buf, 64);
-    hid_read(dev_pkt_0x11, usb_buf, 20);
-}
-
-void LogitechGProKeyboardController::SendMode
-    (
-    unsigned char       zone,
-    unsigned char       mode,
-    unsigned short      speed,
-    unsigned char       red,
-    unsigned char       green,
-    unsigned char       blue
-    )
-{
-    unsigned char usb_buf[20];
-
-    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
-    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up Lighting Control packet                        |
-    \*-----------------------------------------------------*/
-    usb_buf[0x00]           = 0x11;
-    usb_buf[0x01]           = 0xFF;
-    usb_buf[0x02]           = 0x0D;
-    usb_buf[0x03]           = 0x3D;
-    usb_buf[0x04]           = zone;
-
-    usb_buf[0x05]           = mode;
-
-    usb_buf[0x06]           = red;
-    usb_buf[0x07]           = green;
-    usb_buf[0x08]           = blue;
-
-    speed = 100 * speed;
-    if(mode == LOGITECH_GPRO_MODE_CYCLE)
-    {
-        usb_buf[0x0B]       = speed >> 8;
-        usb_buf[0x0C]       = speed & 0xFF;
-        usb_buf[0x0D]       = 0x64;
-    }
-    else if(mode == LOGITECH_GPRO_MODE_BREATHING)
-    {
-        usb_buf[0x09]       = speed >> 8;
-        usb_buf[0x0A]       = speed & 0xFF;
-        usb_buf[0x0C]       = 0x64;
-    }
-
-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    hid_write(dev_pkt_0x11, usb_buf, 20);
-    hid_read(dev_pkt_0x11, usb_buf, 20);
-}

Controllers/LogitechController/LogitechGProKeyboardController/LogitechGProKeyboardController.h

@@ -1,102 +0,0 @@
-/*---------------------------------------------------------*\
-| LogitechGProController.h                                  |
-|                                                           |
-|   Driver for Logitech G Pro keyboard                      |
-|                                                           |
-|   sanchezzzs                                  20 Oct 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#pragma once
-
-#include <string>
-#include <hidapi.h>
-#include "RGBController.h"
-
-enum
-{
-    LOGITECH_GPRO_ZONE_MODE_KEYBOARD     = 0x00,
-    LOGITECH_GPRO_ZONE_MODE_LOGO         = 0x01,
-};
-
-enum
-{
-    LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD   = 0x01,
-    LOGITECH_GPRO_ZONE_DIRECT_MEDIA      = 0x02,
-    LOGITECH_GPRO_ZONE_DIRECT_LOGO       = 0x10,
-    LOGITECH_GPRO_ZONE_DIRECT_INDICATORS = 0x40,
-};
-
-enum
-{
-    LOGITECH_GPRO_MODE_OFF               = 0x00,
-    LOGITECH_GPRO_MODE_STATIC            = 0x01,
-    LOGITECH_GPRO_MODE_BREATHING         = 0x02,
-    LOGITECH_GPRO_MODE_CYCLE             = 0x03,
-    LOGITECH_GPRO_MODE_WAVE              = 0x04,
-};
-
-/*---------------------------------------------------------------------------------------------*\
-| Speed is 1000 for fast and 20000 for slow.                                                    |
-| Values are multiplied by 100 later to give lots of GUI steps.                                 |
-\*---------------------------------------------------------------------------------------------*/
-enum
-{
-    LOGITECH_GPRO_SPEED_SLOWEST          = 0xC8,     /* Slowest speed                       */
-    LOGITECH_GPRO_SPEED_NORMAL           = 0x32,     /* Normal speed                        */
-    LOGITECH_GPRO_SPEED_FASTEST          = 0x0A,     /* Fastest speed                       */
-};
-
-class LogitechGProKeyboardController
-{
-public:
-    LogitechGProKeyboardController(hid_device* dev_handle_0x11, hid_device* dev_handle_0x12, std::string dev_name);
-    ~LogitechGProKeyboardController();
-
-    std::string GetNameString();
-    std::string GetSerialString();
-
-    void        Commit();
-
-    void        SetDirect
-                    (
-                    unsigned char       zone,
-                    unsigned char       frame_count,
-                    unsigned char *     frame_data
-                    );
-
-    void        SetMode
-                    (
-                    unsigned char       mode,
-                    unsigned short      speed,
-                    unsigned char       red,
-                    unsigned char       green,
-                    unsigned char       blue
-                    );
-
-private:
-    hid_device* dev_pkt_0x11;
-    hid_device* dev_pkt_0x12;
-    std::string name;
-
-    void        SendDirectFrame
-                    (
-                    unsigned char       zone,
-                    unsigned char       frame_count,
-                    unsigned char *     frame_data
-                    );
-
-    void        SendMode
-                    (
-                    unsigned char       zone,
-                    unsigned char       mode,
-                    unsigned short      speed,
-                    unsigned char       red,
-                    unsigned char       green,
-                    unsigned char       blue
-                    );
-
-    void        SendCommit();
-};

Controllers/LogitechController/LogitechGProKeyboardController/RGBController_LogitechGProKeyboard.cpp

@@ -1,356 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_LogitechGPro.cpp                            |
-|                                                           |
-|   RGBController for Logitech G Pro keyboard               |
-|                                                           |
-|   sanchezzzs                                  20 Oct 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include "RGBControllerKeyNames.h"
-#include "RGBController_LogitechGProKeyboard.h"
-
-//0xFFFFFFFF indicates an unused entry in matrix
-#define NA  0xFFFFFFFF
-
-static unsigned int matrix_map[7][19] =
-    { {  89,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  NA,  93,  92,  NA,  NA,  91,  NA,  90 },
-      {  37,  NA,  54,  55,  56,  57,  NA,  58,  59,  60,  61,  NA,  62,  63,  64,  65,  66,  67,  68 },
-      {  49,  26,  27,  28,  29,  30,  31,  32,  33,  34,  35,  NA,  41,  42,  38,  NA,  69,  70,  71 },
-      {  39,  NA,  16,  22,   4,  17,  NA,  19,  24,  20,   8,  14,  15,  43,  44,  45,  72,  73,  74 },
-      {  53,  NA,   0,  18,   3,   5,  NA,   6,   7,   9,  10,  11,  47,  48,  46,  36,  NA,  NA,  NA },
-      {  82,  79,  25,  23,   2,  21,  NA,   1,  NA,  13,  12,  50,  51,  52,  86,  NA,  NA,  78,  NA },
-      {  81,  84,  83,  NA,  NA,  NA,  NA,  40,  NA,  NA,  NA,  NA,  87,  88,  80,  85,  76,  77,  75 } };
-
-static const char* zone_names[] =
-{
-    ZONE_EN_KEYBOARD,
-};
-
-static zone_type zone_types[] =
-{
-    ZONE_TYPE_MATRIX,
-};
-
-static const unsigned int zone_sizes[] =
-{
-    94,
-};
-
-typedef struct
-{
-    const char *        name;
-    const unsigned char zone;
-    const unsigned char idx;
-} led_type;
-
-static const led_type led_names[] =
-{
-    /* Key Label                Zone,                                   Index  */
-    { KEY_EN_A,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x04    },//00
-    { KEY_EN_B,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x05    },
-    { KEY_EN_C,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x06    },
-    { KEY_EN_D,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x07    },
-    { KEY_EN_E,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x08    },
-    { KEY_EN_F,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x09    },
-    { KEY_EN_G,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x0A    },
-    { KEY_EN_H,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x0B    },
-    { KEY_EN_I,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x0C    },
-    { KEY_EN_J,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x0D    },
-    { KEY_EN_K,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x0E    },//10
-    { KEY_EN_L,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x0F    },
-    { KEY_EN_M,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x10    },
-    { KEY_EN_N,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x11    },
-    { KEY_EN_O,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x12    },
-    { KEY_EN_P,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x13    },
-    { KEY_EN_Q,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x14    },
-    { KEY_EN_R,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x15    },
-    { KEY_EN_S,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x16    },
-    { KEY_EN_T,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x17    },
-    { KEY_EN_U,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x18    },//20
-    { KEY_EN_V,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x19    },
-    { KEY_EN_W,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x1A    },
-    { KEY_EN_X,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x1B    },
-    { KEY_EN_Y,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x1C    },
-    { KEY_EN_Z,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x1D    },
-    { KEY_EN_1,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x1E    },
-    { KEY_EN_2,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x1F    },
-    { KEY_EN_3,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x20    },
-    { KEY_EN_4,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x21    },
-    { KEY_EN_5,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x22    },//30
-    { KEY_EN_6,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x23    },
-    { KEY_EN_7,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x24    },
-    { KEY_EN_8,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x25    },
-    { KEY_EN_9,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x26    },
-    { KEY_EN_0,                 LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x27    },
-    { KEY_EN_ANSI_ENTER,        LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x28    },
-    { KEY_EN_ESCAPE,            LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x29    },
-    { KEY_EN_BACKSPACE,         LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x2A    },
-    { KEY_EN_TAB,               LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x2B    },
-    { KEY_EN_SPACE,             LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x2C    },//40
-    { KEY_EN_MINUS,             LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x2D    },
-    { KEY_EN_EQUALS,            LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x2E    },
-    { KEY_EN_LEFT_BRACKET,      LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x2F    },
-    { KEY_EN_RIGHT_BRACKET,     LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x30    },
-    { KEY_EN_ANSI_BACK_SLASH,   LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x31    },//ANSI only
-    { KEY_EN_POUND,             LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x32    },//ISO only
-    { KEY_EN_SEMICOLON,         LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x33    },
-    { KEY_EN_QUOTE,             LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x34    },
-    { KEY_EN_BACK_TICK,         LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x35    },
-    { KEY_EN_COMMA,             LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x36    },//50
-    { KEY_EN_PERIOD,            LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x37    },
-    { KEY_EN_FORWARD_SLASH,     LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x38    },
-    { KEY_EN_CAPS_LOCK,         LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x39    },
-    { KEY_EN_F1,                LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x3A    },
-    { KEY_EN_F2,                LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x3B    },
-    { KEY_EN_F3,                LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x3C    },
-    { KEY_EN_F4,                LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x3D    },
-    { KEY_EN_F5,                LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x3E    },
-    { KEY_EN_F6,                LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x3F    },
-    { KEY_EN_F7,                LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x40    },//60
-    { KEY_EN_F8,                LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x41    },
-    { KEY_EN_F9,                LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x42    },
-    { KEY_EN_F10,               LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x43    },
-    { KEY_EN_F11,               LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x44    },
-    { KEY_EN_F12,               LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x45    },
-    { KEY_EN_PRINT_SCREEN,      LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x46    },
-    { KEY_EN_SCROLL_LOCK,       LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x47    },
-    { KEY_EN_PAUSE_BREAK,       LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x48    },
-    { KEY_EN_INSERT,            LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x49    },
-    { KEY_EN_HOME,              LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x4A    },//70
-    { KEY_EN_PAGE_UP,           LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x4B    },
-    { KEY_EN_DELETE,            LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x4C    },
-    { KEY_EN_END,               LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x4D    },
-    { KEY_EN_PAGE_DOWN,         LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x4E    },
-    { KEY_EN_RIGHT_ARROW,       LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x4F    },
-    { KEY_EN_LEFT_ARROW,        LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x50    },
-    { KEY_EN_DOWN_ARROW,        LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x51    },
-    { KEY_EN_UP_ARROW,          LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x52    },
-    { KEY_EN_ISO_BACK_SLASH,    LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x64    },//ISO only
-    { KEY_EN_MENU,              LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0x65    },//80
-    { KEY_EN_LEFT_CONTROL,      LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0xE0    },
-    { KEY_EN_LEFT_SHIFT,        LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0xE1    },
-    { KEY_EN_LEFT_ALT,          LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0xE2    },
-    { KEY_EN_LEFT_WINDOWS,      LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0xE3    },
-    { KEY_EN_RIGHT_CONTROL,     LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0xE4    },
-    { KEY_EN_RIGHT_SHIFT,       LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0xE5    },
-    { KEY_EN_RIGHT_ALT,         LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0xE6    },
-    { KEY_EN_RIGHT_FUNCTION,    LOGITECH_GPRO_ZONE_DIRECT_KEYBOARD,     0xE7    },
-    { "Logo",                   LOGITECH_GPRO_ZONE_DIRECT_LOGO,         0x01    },
-    { "Lighting",               LOGITECH_GPRO_ZONE_DIRECT_INDICATORS,   0x01    },//90
-    { "Game Mode",              LOGITECH_GPRO_ZONE_DIRECT_INDICATORS,   0x02    },
-    { "Caps Lock Indicator",    LOGITECH_GPRO_ZONE_DIRECT_INDICATORS,   0x03    },
-    { "Scroll Lock Indicator",  LOGITECH_GPRO_ZONE_DIRECT_INDICATORS,   0x04    },//93
-};
-
-/**------------------------------------------------------------------*\
-    @name Logitech G Pro
-    @category Keyboard
-    @type USB
-    @save :robot:
-    @direct :white_check_mark:
-    @effects :white_check_mark:
-    @detectors DetectLogitechKeyboardGPro
-    @comment
-\*-------------------------------------------------------------------*/
-
-RGBController_LogitechGProKeyboard::RGBController_LogitechGProKeyboard(LogitechGProKeyboardController* controller_ptr)
-{
-    controller                      = controller_ptr;
-
-    name                            = controller->GetNameString();
-    vendor                          = "Logitech";
-    type                            = DEVICE_TYPE_KEYBOARD;
-    description                     = "Logitech Keyboard Device";
-    serial                          = controller->GetSerialString();
-
-    mode Direct;
-    Direct.name                     = "Direct";
-    Direct.value                    = 0xFFFF;
-    Direct.flags                    = MODE_FLAG_HAS_PER_LED_COLOR;
-    Direct.color_mode               = MODE_COLORS_PER_LED;
-    modes.push_back(Direct);
-
-    mode Static;
-    Static.name                     = "Static";
-    Static.value                    = LOGITECH_GPRO_MODE_STATIC;
-    Static.flags                    = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR;
-    Static.colors_min               = 1;
-    Static.colors_max               = 1;
-    Static.color_mode               = MODE_COLORS_MODE_SPECIFIC;
-    Static.colors.resize(1);
-    modes.push_back(Static);
-
-    mode Off;
-    Off.name                        = "Off";
-    Off.value                       = LOGITECH_GPRO_MODE_OFF;
-    Off.flags                       = 0;
-    Off.color_mode                  = MODE_COLORS_NONE;
-    modes.push_back(Off);
-
-    mode Cycle;
-    Cycle.name                      = "Cycle";
-    Cycle.value                     = LOGITECH_GPRO_MODE_CYCLE;
-    Cycle.flags                     = MODE_FLAG_HAS_SPEED;
-    Cycle.color_mode                = MODE_COLORS_NONE;
-    Cycle.speed_min                 = LOGITECH_GPRO_SPEED_SLOWEST;
-    Cycle.speed_max                 = LOGITECH_GPRO_SPEED_FASTEST;
-    Cycle.speed                     = LOGITECH_GPRO_SPEED_NORMAL;
-    modes.push_back(Cycle);
-
-    mode Breathing;
-    Breathing.name                  = "Breathing";
-    Breathing.value                 = LOGITECH_GPRO_MODE_BREATHING;
-    Breathing.flags                 = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR | MODE_FLAG_HAS_SPEED;
-    Breathing.colors_min            = 1;
-    Breathing.colors_max            = 1;
-    Breathing.color_mode            = MODE_COLORS_MODE_SPECIFIC;
-    Breathing.colors.resize(1);
-    Breathing.speed_min             = LOGITECH_GPRO_SPEED_SLOWEST;
-    Breathing.speed_max             = LOGITECH_GPRO_SPEED_FASTEST;
-    Breathing.speed                 = LOGITECH_GPRO_SPEED_NORMAL;
-    modes.push_back(Breathing);
-
-    SetupZones();
-}
-
-RGBController_LogitechGProKeyboard::~RGBController_LogitechGProKeyboard()
-{
-    Shutdown();
-
-    delete controller;
-}
-
-void RGBController_LogitechGProKeyboard::SetupZones()
-{
-    /*---------------------------------------------------------*\
-    | Set up zones                                              |
-    \*---------------------------------------------------------*/
-    unsigned int total_led_count = 0;
-    for(unsigned int zone_idx = 0; zone_idx < 1; zone_idx++)
-    {
-        zone new_zone;
-        new_zone.name                   = zone_names[zone_idx];
-        new_zone.type                   = zone_types[zone_idx];
-        new_zone.leds_min               = zone_sizes[zone_idx];
-        new_zone.leds_max               = zone_sizes[zone_idx];
-        new_zone.leds_count             = zone_sizes[zone_idx];
-
-        if(zone_types[zone_idx] == ZONE_TYPE_MATRIX)
-        {
-            new_zone.matrix_map.Set(7, 19, (unsigned int *)&matrix_map);
-        }
-
-        zones.push_back(new_zone);
-
-        total_led_count += zone_sizes[zone_idx];
-    }
-
-    for(unsigned int led_idx = 0; led_idx < total_led_count; led_idx++)
-    {
-        led new_led;
-        new_led.name                    = led_names[led_idx].name;
-        new_led.value                   = ( led_names[led_idx].zone << 8 ) + led_names[led_idx].idx;
-        leds.push_back(new_led);
-    }
-
-    SetupColors();
-}
-
-void RGBController_LogitechGProKeyboard::DeviceUpdateLEDs()
-{
-    #define MAX_FRAMES_PER_PACKET 0x0E
-
-    unsigned char frame_buf[MAX_FRAMES_PER_PACKET * 4];
-    unsigned char frame_cnt = 0;
-    unsigned char prev_zone = 0;
-    unsigned char zone      = 0;
-    unsigned char idx       = 0;
-
-    /*---------------------------------------------------------*\
-    | TODO: Send packets with multiple LED frames               |
-    \*---------------------------------------------------------*/
-    for(std::size_t led_idx = 0; led_idx < leds.size(); led_idx++)
-    {
-        zone = ( leds[led_idx].value >> 8 );
-        idx  = ( leds[led_idx].value & 0xFF );
-
-        if((zone != prev_zone) && (frame_cnt != 0))
-        {
-            controller->SetDirect(prev_zone, frame_cnt, frame_buf);
-            frame_cnt = 0;
-        }
-
-        frame_buf[(frame_cnt * 4) + 0] = idx;
-        frame_buf[(frame_cnt * 4) + 1] = RGBGetRValue(colors[led_idx]);
-        frame_buf[(frame_cnt * 4) + 2] = RGBGetGValue(colors[led_idx]);
-        frame_buf[(frame_cnt * 4) + 3] = RGBGetBValue(colors[led_idx]);
-
-        frame_cnt++;
-        prev_zone = zone;
-
-        if(frame_cnt == MAX_FRAMES_PER_PACKET)
-        {
-            controller->SetDirect(prev_zone, frame_cnt, frame_buf);
-            frame_cnt = 0;
-        }
-    }
-
-    if(frame_cnt != 0)
-    {
-        controller->SetDirect(prev_zone, frame_cnt, frame_buf);
-    }
-
-    controller->Commit();
-}
-
-void RGBController_LogitechGProKeyboard::DeviceUpdateZoneLEDs(int /*zone*/)
-{
-    DeviceUpdateLEDs();
-}
-
-void RGBController_LogitechGProKeyboard::DeviceUpdateSingleLED(int led)
-{
-    unsigned char frame[4];
-    unsigned char zone;
-    unsigned char idx;
-
-    zone = ( leds[led].value >> 8 );
-    idx  = ( leds[led].value & 0xFF );
-
-    frame[0] = idx;
-    frame[1] = RGBGetRValue(colors[led]);
-    frame[2] = RGBGetGValue(colors[led]);
-    frame[3] = RGBGetBValue(colors[led]);
-
-    controller->SetDirect(zone, 1, frame);
-    controller->Commit();
-}
-
-void RGBController_LogitechGProKeyboard::DeviceUpdateMode()
-{
-    /*---------------------------------------------------------*\
-    | Direct mode does not send a mode packet                   |
-    | Call UpdateLEDs to send direct packet                     |
-    \*---------------------------------------------------------*/
-    if(active_mode == 0xFFFF)
-    {
-        UpdateLEDsInternal();
-        return;
-    }
-
-    unsigned char red = 0;
-    unsigned char grn = 0;
-    unsigned char blu = 0;
-
-    if(modes[active_mode].color_mode == MODE_COLORS_MODE_SPECIFIC)
-    {
-        red = RGBGetRValue(modes[active_mode].colors[0]);
-        grn = RGBGetGValue(modes[active_mode].colors[0]);
-        blu = RGBGetBValue(modes[active_mode].colors[0]);
-    }
-
-    controller->SetMode(modes[active_mode].value, modes[active_mode].speed, red, grn, blu);
-}

Controllers/LogitechController/LogitechGProKeyboardController/RGBController_LogitechGProKeyboard.h

@@ -1,33 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_LogitechGPro.h                              |
-|                                                           |
-|   RGBController for Logitech G Pro keyboard               |
-|                                                           |
-|   sanchezzzs                                  20 Oct 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#pragma once
-
-#include "RGBController.h"
-#include "LogitechGProKeyboardController.h"
-
-class RGBController_LogitechGProKeyboard : public RGBController
-{
-public:
-    RGBController_LogitechGProKeyboard(LogitechGProKeyboardController* controller_ptr);
-    ~RGBController_LogitechGProKeyboard();
-
-    void        SetupZones();
-
-    void        DeviceUpdateLEDs();
-    void        DeviceUpdateZoneLEDs(int zone);
-    void        DeviceUpdateSingleLED(int led);
-
-    void        DeviceUpdateMode();
-
-private:
-    LogitechGProKeyboardController* controller;
-};

Controllers/LogitechController/LogitechHIDPP20Controller/LogitechHIDPP20Controller.cpp

@@ -922,23 +922,6 @@ bool LogitechHIDPP20Controller::PrefersShortFrame(size_t len) const
 #endif
 }
 
-/*---------------------------------------------------------*\
-| Outgoing frame as hex, for trace-level wire comparison.   |
-\*---------------------------------------------------------*/
-static std::string hex_frame(const uint8_t* buf, size_t len)
-{
-    std::string out;
-    char        byte[4];
-
-    for(size_t i = 0; i < len; i++)
-    {
-        snprintf(byte, sizeof(byte), "%02X ", buf[i]);
-        out += byte;
-    }
-
-    return out;
-}
-
 int LogitechHIDPP20Controller::SendStandard
     (
     uint8_t         feat_idx,
@@ -1011,11 +994,6 @@ int LogitechHIDPP20Controller::SendStandard
         result = hid_write(dev, buf, msg_len);
     }
 
-    if(LogManager::get()->GetLogLevel() >= LL_TRACE)
-    {
-        LOG_TRACE("%s TX %s(result=%d)", LOG_TAG, hex_frame(buf, msg_len).c_str(), result);
-    }
-
     /*-----------------------------------------------------*\
     | A collection with no short report rejects the 0x10    |
     | write (G560, G933). Resend as long and stay long.     |
@@ -1043,11 +1021,6 @@ int LogitechHIDPP20Controller::SendStandard
             result = hid_write(dev, buf, LOGITECH_LONG_MESSAGE_LEN);
         }
 
-        if(LogManager::get()->GetLogLevel() >= LL_TRACE)
-        {
-            LOG_TRACE("%s TX %s(result=%d)", LOG_TAG, hex_frame(buf, LOGITECH_LONG_MESSAGE_LEN).c_str(), result);
-        }
-
         if(result >= 0)
         {
             LOG_DEBUG("%s Short report rejected, using long frames", LOG_TAG);
@@ -1199,9 +1172,6 @@ int LogitechHIDPP20Controller::ReadStandardDirect
         {
             if(response.device_index != device_index)
             {
-                LOG_TRACE("%s ReadStandardDirect: dropping frame for index 0x%02X (ours 0x%02X)",
-                          LOG_TAG, response.device_index, device_index);
-
                 if(++drained > HIDPP20_READ_DRAIN_BUDGET)
                 {
                     LOG_DEBUG("%s ReadStandardDirect: drain budget (%d) exceeded",
@@ -4829,18 +4799,9 @@ int LogitechHIDPP20Controller::ProcessOnePerKeyResponse(int timeout_ms, uint8_t
     {
         /*-------------------------------------------------*\
         | Echo format unknown for this function, count      |
-        | it toward the group, and log the payload so a     |
-        | real run teaches us what the firmware echoes.     |
+        | it toward the group.                              |
         \*-------------------------------------------------*/
         frame_unmatched_acks[resp_func & 0xF0]++;
-
-        char hex[16 * 3 + 1];
-        for(int b = 0; b < 16; b++)
-        {
-            snprintf(&hex[b * 3], 4, "%02X ", resp_data[b]);
-        }
-        LOG_TRACE("%s per-key ACK echo unmatched func=0x%02X data=[%s]",
-                  LOG_TAG, resp_func, hex);
     }
 
     return 1;
@@ -4902,11 +4863,6 @@ void LogitechHIDPP20Controller::SubmitPerKeyFrame(const std::vector<RGBColor>& f
     {
         std::lock_guard<std::mutex> lock(pending_frame_mutex);
 
-        if(pending_frame_valid)
-        {
-            pending_frames_skipped++;
-        }
-
         pending_frame       = frame;
         pending_frame_valid = true;
     }
@@ -4919,7 +4875,6 @@ void LogitechHIDPP20Controller::SenderThreadFunc()
     while(sender_running.load())
     {
         std::vector<RGBColor> frame;
-        uint32_t              skipped = 0;
 
         {
             std::unique_lock<std::mutex> lock(pending_frame_mutex);
@@ -4936,13 +4891,6 @@ void LogitechHIDPP20Controller::SenderThreadFunc()
 
             frame               = std::move(pending_frame);
             pending_frame_valid = false;
-            skipped                = pending_frames_skipped;
-            pending_frames_skipped = 0;
-        }
-
-        if(skipped > 0)
-        {
-            LOG_TRACE("%s sender skipped %u stale frame(s)", LOG_TAG, skipped);
         }
 
         /*-------------------------------------------------*\
@@ -5437,6 +5385,7 @@ PerKeyFrameResult LogitechHIDPP20Controller::PerKeyFrameEnd()
         if(lost > 0)
         {
             perkey_clean_frames = 0;
+            perkey_acks_lost   += lost;
 
             if(perkey_window > HIDPP20_PERKEY_WINDOW_MIN)
             {
@@ -5446,9 +5395,6 @@ PerKeyFrameResult LogitechHIDPP20Controller::PerKeyFrameEnd()
                 {
                     perkey_window = HIDPP20_PERKEY_WINDOW_MIN;
                 }
-
-                LOG_DEBUG("%s %zu write ACK(s) lost, write window now %zu",
-                          LOG_TAG, lost, perkey_window);
             }
         }
         else if(perkey_window < HIDPP20_PERKEY_WINDOW_MAX &&
@@ -5472,34 +5418,55 @@ PerKeyFrameResult LogitechHIDPP20Controller::PerKeyFrameEnd()
         DrainStaleResponses();
     }
 
+    /*-----------------------------------------------------*\
+    | Link quality. A lost ACK or an unfinished frame is    |
+    | the link's normal backpressure and the next frame     |
+    | resends what did not land, so single frames are not   |
+    | logged. Counts are summarized once per interval,      |
+    | and only when something was lost.                     |
+    \*-----------------------------------------------------*/
     if(!result.attempted_zones.empty())
     {
-        std::chrono::steady_clock::time_point frame_done = std::chrono::steady_clock::now();
+        perkey_frames_seen++;
 
-        int send_ms = (int)std::chrono::duration_cast<std::chrono::milliseconds>(
-                            send_done - frame_first_write).count();
-        int ack_ms  = (int)std::chrono::duration_cast<std::chrono::milliseconds>(
-                            acks_done - send_done).count();
-        int fe_ms   = (int)std::chrono::duration_cast<std::chrono::milliseconds>(
-                            frame_done - acks_done).count();
-
-        if(complete)
+        if(frame_aborted)
         {
-            LOG_TRACE("%s frame committed: %zu zones, %zu packets (%zu echo-matched) "
-                      "send=%dms ack=%dms fe=%dms pred=%ums busy=%d win=%zu",
-                      LOG_TAG, result.attempted_zones.size(), frame_packets.size(),
-                      frame_exact_acks, send_ms, ack_ms, fe_ms, predicted_ms, busy_polls,
-                      perkey_window);
+            perkey_frames_aborted++;
         }
-        else
+        else if(!complete)
         {
-            LOG_DEBUG("%s frame %s: %zu/%zu zones acked (%zu packets, %zu echo-matched), "
-                      "frame_end=%d, send=%dms ack=%dms fe=%dms pred=%ums busy=%d win=%zu",
-                      LOG_TAG, frame_aborted ? "aborted" : "partial",
-                      result.acked_zones.size(), result.attempted_zones.size(),
-                      frame_packets.size(), frame_exact_acks,
-                      (int)result.frame_end_acked, send_ms, ack_ms, fe_ms, predicted_ms,
-                      busy_polls, perkey_window);
+            perkey_frames_partial++;
+        }
+
+        if(!result.frame_end_acked)
+        {
+            perkey_frames_no_end++;
+        }
+
+        std::chrono::steady_clock::time_point now = std::chrono::steady_clock::now();
+
+        if(perkey_summary_time == std::chrono::steady_clock::time_point())
+        {
+            perkey_summary_time = now;
+        }
+        else if(now - perkey_summary_time >= std::chrono::seconds(HIDPP20_PERKEY_SUMMARY_S))
+        {
+            if(perkey_frames_partial > 0 || perkey_frames_aborted > 0 ||
+               perkey_frames_no_end  > 0 || perkey_acks_lost      > 0)
+            {
+                LOG_DEBUG("%s per-key link, last %ds: %zu frames, %zu partial, %zu aborted, "
+                          "%zu without FrameEnd ack, %zu ACKs lost, window %zu",
+                          LOG_TAG, HIDPP20_PERKEY_SUMMARY_S, perkey_frames_seen,
+                          perkey_frames_partial, perkey_frames_aborted,
+                          perkey_frames_no_end, perkey_acks_lost, perkey_window);
+            }
+
+            perkey_frames_seen    = 0;
+            perkey_frames_partial = 0;
+            perkey_frames_aborted = 0;
+            perkey_frames_no_end  = 0;
+            perkey_acks_lost      = 0;
+            perkey_summary_time   = now;
         }
     }
 
@@ -5855,15 +5822,6 @@ void LogitechHIDPP20Controller::SetZoneEffect
     \*-----------------------------------------------------*/
     data[12] = persist ? 0x01 : 0x00;
 
-    LOG_DEBUG("%s SetEffect cluster=%u idx=%u id=0x%04X "
-              "data=[%02X %02X %02X %02X %02X %02X %02X %02X "
-              "%02X %02X %02X %02X %02X %02X %02X %02X]",
-              LOG_TAG, cluster_idx, effect_idx, effect_id,
-              data[0], data[1], data[2], data[3],
-              data[4], data[5], data[6], data[7],
-              data[8], data[9], data[10], data[11],
-              data[12], data[13], data[14], data[15]);
-
     blankFAPmessage response;
     SendAckedIntoFAP(caps.idx_rgb_effects, caps.fn_set_effect,
                      data, 16, response);
@@ -5951,9 +5909,6 @@ void LogitechHIDPP20Controller::SetHeadsetRGBHostmodeColors
     uint8_t frame_end[4] = { 0x01, 0x00, 0x00, 0x00 };
     SendAckedIntoFAP(caps.idx_headset_rgb_hostmode, FN_0620_FRAME_END,
                      frame_end, sizeof(frame_end), response);
-
-    LOG_TRACE("%s 0x0620 wrote %zu zone(s) in %zu color group(s), FrameEnd[0x01]",
-              LOG_TAG, zones.size(), groups.size());
 }
 
 /*---------------------------------------------------------*\
@@ -7604,7 +7559,8 @@ void LogitechHIDPP20Controller::ReadActiveProfileSector()
     }
 
     constexpr uint16_t SECTOR_SIZE = 0x63;  // 99 bytes
-    constexpr uint16_t PAGE_SIZE   = 16;
+    constexpr uint16_t SIZE_OF_PAGE   = 16; 
+
 
     /*-----------------------------------------------------*\
     | Step 1: load the sector into the device's read buffer |
@@ -7630,7 +7586,7 @@ void LogitechHIDPP20Controller::ReadActiveProfileSector()
     \*-----------------------------------------------------*/
     uint8_t sector_buf[SECTOR_SIZE] = {};
 
-    for(uint16_t offset = 0; offset < SECTOR_SIZE; offset += PAGE_SIZE)
+    for(uint16_t offset = 0; offset < SECTOR_SIZE; offset += SIZE_OF_PAGE)
     {
         uint8_t read_req[3] = {
             (uint8_t)((offset >> 8) & 0xFF),
@@ -7650,9 +7606,9 @@ void LogitechHIDPP20Controller::ReadActiveProfileSector()
             return;
         }
 
-        size_t copy_len = (offset + PAGE_SIZE > SECTOR_SIZE)
+        size_t copy_len = (offset + SIZE_OF_PAGE > SECTOR_SIZE)
                         ? (size_t)(SECTOR_SIZE - offset)
-                        : PAGE_SIZE;
+                        : SIZE_OF_PAGE;
         memcpy(sector_buf + offset, page_resp, copy_len);
     }
 
@@ -7662,11 +7618,11 @@ void LogitechHIDPP20Controller::ReadActiveProfileSector()
     LOG_DEBUG("%s ProfileSector partition=NVS sector=1 size=%u bytes:",
               LOG_TAG, (unsigned)SECTOR_SIZE);
 
-    for(uint16_t row = 0; row < SECTOR_SIZE; row += PAGE_SIZE)
+    for(uint16_t row = 0; row < SECTOR_SIZE; row += SIZE_OF_PAGE)
     {
-        size_t row_len = (row + PAGE_SIZE > SECTOR_SIZE)
+        size_t row_len = (row + SIZE_OF_PAGE > SECTOR_SIZE)
                        ? (size_t)(SECTOR_SIZE - row)
-                       : PAGE_SIZE;
+                       : SIZE_OF_PAGE;
 
         char hex[64] = {};
         char* p = hex;

Controllers/LogitechController/LogitechHIDPP20Controller/LogitechHIDPP20Controller.h

@@ -510,6 +510,7 @@ static constexpr size_t   HIDPP20_PERKEY_WINDOW_MAX  = 8;
 static constexpr size_t   HIDPP20_PERKEY_WINDOW_MIN  = 2;
 static constexpr uint16_t HIDPP20_PERKEY_ACK_WAIT_MS = 60;
 static constexpr uint16_t HIDPP20_PERKEY_ACK_TAIL_MS = 25;
+static constexpr int      HIDPP20_PERKEY_SUMMARY_S   = 60;
 static constexpr uint8_t  HIDPP20_PERKEY_WINDOW_GROW_AFTER = 16;
 
 /*---------------------------------------------------------*\
@@ -1243,6 +1244,17 @@ private:
     size_t          perkey_window       = HIDPP20_PERKEY_WINDOW_MAX;
     uint8_t         perkey_clean_frames = 0;
 
+    /*-----------------------------------------------------*\
+    | Link quality counters, logged as one summary at most  |
+    | once per HIDPP20_PERKEY_SUMMARY_S.                    |
+    \*-----------------------------------------------------*/
+    size_t          perkey_frames_seen    = 0;
+    size_t          perkey_frames_partial = 0;
+    size_t          perkey_frames_aborted = 0;
+    size_t          perkey_frames_no_end  = 0;
+    size_t          perkey_acks_lost      = 0;
+    std::chrono::steady_clock::time_point perkey_summary_time;
+
     void            ResetPerKeyFrameState();
 
     /*-----------------------------------------------------*\
@@ -1293,7 +1305,6 @@ private:
     std::condition_variable pending_frame_cv;
     std::vector<RGBColor>   pending_frame;
     bool                    pending_frame_valid    = false;
-    uint32_t                pending_frames_skipped = 0;
 
     /*-----------------------------------------------------*\
     | Callbacks                                             |

Controllers/LogitechController/LogitechHIDPP20Controller/RGBController_LogitechHIDPP20.cpp

@@ -329,6 +329,10 @@ static const std::map<uint16_t, std::string> hidpp20_extras_names =
     { 182, "G3"                },
     { 183, "G4"                },
     { 184, "G5"                },
+    { 185, "G6"                },
+    { 186, "G7"                },
+    { 187, "G8"                },
+    { 188, "G9"                },
     { 210, "Logo"              },
 };
 
@@ -423,9 +427,39 @@ static const keyboard_led proxrapid_top_strip[] =
     { 0, 0, 13, 153, "Media Mute",       KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },   /* above F12 */
 };
 
+/*---------------------------------------------------------*\
+| G915 X Wired top strip and G-key column: INSERT_ROW adds  |
+| row 0 above the F-row, the rest INSERT_SHIFT_RIGHT into   |
+| it. G1-G5 insert at column 0 of the main rows; the unused |
+| key at the F-row's column 0 shifts that row right so it   |
+| stays aligned with them. Zone ids hardware-probed on this |
+| board. Game Mode (above F5) is a non-RGB toggle, so none  |
+| is listed.                                                |
+\*---------------------------------------------------------*/
+static const keyboard_led g915x_strip_and_gkeys[] =
+{
+    { 0, 0, 0,  210, "Logo",             KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_ROW         },
+    { 0, 1, 0,  0,   KEY_EN_UNUSED,      KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },   /* shift the F-row  */
+    { 0, 2, 0,  180, "G1",               KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },
+    { 0, 3, 0,  181, "G2",               KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },
+    { 0, 4, 0,  182, "G3",               KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },
+    { 0, 5, 0,  183, "G4",               KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },
+    { 0, 6, 0,  184, "G5",               KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },
+    { 0, 0, 3,  185, "G6",               KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },   /* above F1         */
+    { 0, 0, 4,  186, "G7",               KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },   /* above F2         */
+    { 0, 0, 5,  187, "G8",               KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },   /* above F3         */
+    { 0, 0, 6,  188, "G9",               KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },   /* above F4         */
+    { 0, 0, 8,  153, "Brightness",       KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },   /* above F6         */
+    { 0, 0, 18, 158, "Media Previous",   KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },   /* above Num Lock   */
+    { 0, 0, 19, 155, "Media Play/Pause", KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },   /* above Numpad /   */
+    { 0, 0, 20, 157, "Media Next",       KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },   /* above Numpad *   */
+    { 0, 0, 21, 156, "Media Mute",       KEY_EN_UNUSED, KEYBOARD_OPCODE_INSERT_SHIFT_RIGHT },   /* above Numpad -   */
+};
+
 static const KbLayoutEdit known_kb_layout_edits[] =
 {
     { 0xC35B, proxrapid_top_strip,      5  },   /* PRO X RAPID */
+    { 0xC359, g915x_strip_and_gkeys,    16 },   /* G915 X Wired */
 };
 
 static key_set FindKbLayoutEdit(uint16_t pid_wired, uint16_t pid_wireless)
@@ -804,9 +838,10 @@ static const keyboard_led g512_top_strip[] =
 | legacy map: the media cluster above the numpad (on/off    |
 | backlight, not RGB; the firmware still advertises media   |
 | keyType 0x02, see the C32B quirk) and the four small      |
-| mode keys left of G6, which nothing has identified yet.   |
-| If firmware enumerates any of these they surface in       |
-| Extras (suppression is off for this board).               |
+| mode keys left of G6. Painting the advertised extras      |
+| controls nothing (hardware-observed), so unclaimed ids    |
+| are suppressed as phantoms; the plugin's Show Unmapped    |
+| override surfaces them for auditing.                      |
 \*---------------------------------------------------------*/
 static const keyboard_led g910_side_strip[] =
 {
@@ -831,15 +866,15 @@ static const keyboard_led g910_side_strip[] =
 \*---------------------------------------------------------*/
 static const Kb8080Strip known_kb_8080_strips[] =
 {
-    { 0xC331, true,  g810_top_strip, 11, false },  /* G810             */
-    { 0xC337, true,  g810_top_strip, 11, false },  /* G810             */
-    { 0xC333, true,  g810_top_strip, 11, false },  /* G610             */
-    { 0xC338, true,  g810_top_strip, 11, false },  /* G610             */
+    { 0xC331, true,  g810_top_strip, 11, true  },  /* G810             */
+    { 0xC337, true,  g810_top_strip, 11, true  },  /* G810             */
+    { 0xC333, true,  g810_top_strip, 11, true  },  /* G610             */
+    { 0xC338, true,  g810_top_strip, 11, true  },  /* G610             */
     { 0xC342, true,  g512_top_strip, 2,  true  },  /* G512             */
     { 0xC33C, true,  g512_top_strip, 2,  true  },  /* G512 RGB         */
-    { 0xC32B, true,  g910_side_strip, 11, false }, /* G910 Orion Spark */
-    { 0xC335, true,  g910_side_strip, 11, false }, /* G910             */
-    { 0xC339, false, gpro_top_strip, 5,  false },  /* G Pro            */
+    { 0xC32B, true,  g910_side_strip, 11, true  }, /* G910 Orion Spark */
+    { 0xC335, true,  g910_side_strip, 11, true  }, /* G910             */
+    { 0xC339, false, gpro_top_strip, 5,  true  },  /* G Pro            */
 };
 
 static const Kb8080Strip* FindKb8080Strip(uint16_t pid_wired, uint16_t pid_wireless)
@@ -855,9 +890,10 @@ static const Kb8080Strip* FindKb8080Strip(uint16_t pid_wired, uint16_t pid_wirel
     return(nullptr);
 }
 
-RGBController_LogitechHIDPP20::RGBController_LogitechHIDPP20(LogitechHIDPP20Controller* controller_ptr)
+RGBController_LogitechHIDPP20::RGBController_LogitechHIDPP20(LogitechHIDPP20Controller* controller_ptr, std::function<void ()> callback)
 {
     controller = controller_ptr;
+    shutdown_callback = callback;
 
     const HIDPP20DeviceCapabilities& caps = controller->GetCapabilities();
 
@@ -988,6 +1024,27 @@ RGBController_LogitechHIDPP20::RGBController_LogitechHIDPP20(LogitechHIDPP20Cont
     {
         const HIDPP20ZoneCluster& cluster = caps.zone_clusters[0];
 
+        /*-------------------------------------------------*\
+        | Per-LED effect colors: multi-cluster devices      |
+        | whose only paint path is zone effects, one color  |
+        | per cluster. Per-key devices take a single mode   |
+        | color: the UI repaints per-key on any per-LED     |
+        | mode set, which overwrites the zone effect.       |
+        \*-------------------------------------------------*/
+        const bool per_led_colors = (caps.zone_clusters.size() > 1)
+                                 && !caps.has_perkey
+                                 && !PerKey8080Capable();
+
+        /*-------------------------------------------------*\
+        | 0x8070 keyboard firmware ignores the Cycle, Wave  |
+        | and Breathing intensity byte (G810/G910           |
+        | hardware); the same slots drive brightness on     |
+        | the mice. No slider for a dead control; the wire  |
+        | still sends 100 in that slot.                     |
+        \*-------------------------------------------------*/
+        const bool effect_brightness = !(caps.rgb_feature_page == HIDPP20_FEAT_COLOR_LED_EFFECTS
+                                      && caps.device_type == LOGITECH_DEVICE_TYPE_KEYBOARD);
+
         for(size_t i = 0; i < cluster.effects.size(); i++)
         {
             const HIDPP20Effect& fx = cluster.effects[i];
@@ -1000,16 +1057,7 @@ RGBController_LogitechHIDPP20::RGBController_LogitechHIDPP20(LogitechHIDPP20Cont
                     Static.name       = "Static";
                     Static.value      = fx.index;
 
-                    /*-------------------------------------*\
-                    | Multi-cluster devices (mice with      |
-                    | logo/scroll/DPI) get per-LED colors   |
-                    | so each zone can be painted           |
-                    | independently in Static. Single-      |
-                    | cluster devices (keyboards, single-   |
-                    | zone mice) keep the single-color      |
-                    | MODE_COLORS_MODE_SPECIFIC UX.         |
-                    \*-------------------------------------*/
-                    if(caps.zone_clusters.size() > 1)
+                    if(per_led_colors)
                     {
                         Static.flags      = MODE_FLAG_HAS_PER_LED_COLOR;
                         Static.color_mode = MODE_COLORS_PER_LED;
@@ -1031,8 +1079,11 @@ RGBController_LogitechHIDPP20::RGBController_LogitechHIDPP20(LogitechHIDPP20Cont
                     mode Cycle;
                     Cycle.name           = "Spectrum Cycle";
                     Cycle.value          = fx.index;
-                    Cycle.flags          = MODE_FLAG_HAS_SPEED
-                                         | MODE_FLAG_HAS_BRIGHTNESS;
+                    Cycle.flags          = MODE_FLAG_HAS_SPEED;
+                    if(effect_brightness)
+                    {
+                        Cycle.flags     |= MODE_FLAG_HAS_BRIGHTNESS;
+                    }
                     Cycle.speed_min      = HIDPP20_SPEED_SLIDER_MIN;
                     Cycle.speed_max      = HIDPP20_SPEED_SLIDER_MAX;
                     Cycle.speed          = 80;     /* ~4.9s, lively medium */
@@ -1056,11 +1107,7 @@ RGBController_LogitechHIDPP20::RGBController_LogitechHIDPP20(LogitechHIDPP20Cont
                     Breathing.brightness_max = 100;
                     Breathing.brightness     = 100;
 
-                    /*-------------------------------------*\
-                    | See Static above, multi-              |
-                    | cluster gets per-LED colors.          |
-                    \*-------------------------------------*/
-                    if(caps.zone_clusters.size() > 1)
+                    if(per_led_colors)
                     {
                         Breathing.flags      = MODE_FLAG_HAS_PER_LED_COLOR
                                              | MODE_FLAG_HAS_SPEED
@@ -1077,6 +1124,12 @@ RGBController_LogitechHIDPP20::RGBController_LogitechHIDPP20(LogitechHIDPP20Cont
                         Breathing.color_mode = MODE_COLORS_MODE_SPECIFIC;
                         Breathing.colors.resize(1);
                     }
+
+                    if(!effect_brightness)
+                    {
+                        Breathing.flags &= ~MODE_FLAG_HAS_BRIGHTNESS;
+                    }
+
                     modes.push_back(Breathing);
                     break;
                 }
@@ -1096,7 +1149,7 @@ RGBController_LogitechHIDPP20::RGBController_LogitechHIDPP20(LogitechHIDPP20Cont
                     Visualizer.speed_max  = HIDPP20_SPEED_SLIDER_MAX;
                     Visualizer.speed      = 80;     /* ~4.9s, near the 5s firmware default */
 
-                    if(caps.zone_clusters.size() > 1)
+                    if(per_led_colors)
                     {
                         Visualizer.flags      = MODE_FLAG_HAS_PER_LED_COLOR
                                               | MODE_FLAG_HAS_SPEED;
@@ -1120,8 +1173,11 @@ RGBController_LogitechHIDPP20::RGBController_LogitechHIDPP20(LogitechHIDPP20Cont
                     mode Wave;
                     Wave.name           = "Color Wave";
                     Wave.value          = fx.index;
-                    Wave.flags          = MODE_FLAG_HAS_SPEED
-                                        | MODE_FLAG_HAS_BRIGHTNESS;
+                    Wave.flags          = MODE_FLAG_HAS_SPEED;
+                    if(effect_brightness)
+                    {
+                        Wave.flags     |= MODE_FLAG_HAS_BRIGHTNESS;
+                    }
                     Wave.speed_min      = HIDPP20_SPEED_SLIDER_MIN;
                     Wave.speed_max      = HIDPP20_SPEED_SLIDER_MAX;
                     Wave.speed          = 80;     /* ~4.9s, lively medium */
@@ -1346,6 +1402,11 @@ RGBController_LogitechHIDPP20::~RGBController_LogitechHIDPP20()
 {
     controller->StopPowerManager();
 
+    if(shutdown_callback)
+    {
+        shutdown_callback();
+    }
+
     Shutdown();
 
     delete controller;

Controllers/LogitechController/LogitechHIDPP20Controller/RGBController_LogitechHIDPP20.h

@@ -15,7 +15,7 @@
 class RGBController_LogitechHIDPP20 : public RGBController
 {
 public:
-    RGBController_LogitechHIDPP20(LogitechHIDPP20Controller* controller_ptr);
+    RGBController_LogitechHIDPP20(LogitechHIDPP20Controller* controller_ptr, std::function<void()> shutdown_callback);
     ~RGBController_LogitechHIDPP20();
 
     void        SetupZones();
@@ -116,4 +116,6 @@ private:
     | Parallel to led_to_zone_id; 0x8080 path only.         |
     \*-----------------------------------------------------*/
     std::vector<std::pair<uint16_t, uint8_t>> led_to_keytype_keyid_8080;
+
+    std::function<void()> shutdown_callback;
 };

Controllers/MSIMotherboardController/MSIMotherboard112Controller/MSIMotherboard112Controller.cpp

@@ -38,17 +38,24 @@ MSIMotherboard112Controller::MSIMotherboard112Controller(hid_device* handle, con
     location    = path;
     name        = dev_name;
 
-    if(dev)
-    {
+    /*-----------------------------------------------------*\
+    | Perform initial reads - get the controller's firmware |
+    | version and then read the controller's active         |
+    | configuration data                                    |
+    \*-----------------------------------------------------*/
     ReadFwVersion();
     ReadSettings();
-    }
 
     /*-----------------------------------------------------*\
-    | Initialize save flag                                  |
+    | The last byte of the packet is the save flag.  This   |
+    | byte is stored as a zero in the data flash, but is    |
+    | set to 1 at the protocol level to tell the firmware   |
+    | to save the active configuration to flash.            |
+    | Also set onboard zone to act as sync master for all   |
+    | of the onboard LEDs.                                  |
     \*-----------------------------------------------------*/
     data.save_data                  = 0;
-    data.on_board_led.colorFlags = 0x81;    // force MS bit of color flags to 1 to have expected zone control
+    data.on_board_led.colorFlags    = MSI_COLOR_FLAG_USE_CUSTOM_COLOR | MSI_COLOR_FLAG_SYNC_SETTING_ONBOARD;
 
     /*-----------------------------------------------------*\
     | Initialize zone based per LED data                    |
@@ -56,24 +63,24 @@ MSIMotherboard112Controller::MSIMotherboard112Controller(hid_device* handle, con
     numof_onboard_leds = 7;
     supported_zones    = &zones_set;
 
-    zone_based_per_led_data.j_rgb_1.speedAndBrightnessFlags = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.j_rgb_1.colorFlags = BITSET(zone_based_per_led_data.j_rgb_1.colorFlags, true, 7u);
-    zone_based_per_led_data.j_rainbow_1.speedAndBrightnessFlags = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.j_rainbow_1.colorFlags = BITSET(zone_based_per_led_data.j_rainbow_1.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led.speedAndBrightnessFlags = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led.colorFlags = BITSET(zone_based_per_led_data.on_board_led.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_1.speedAndBrightnessFlags = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_1.colorFlags = BITSET(zone_based_per_led_data.on_board_led_1.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_2.speedAndBrightnessFlags = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_2.colorFlags = BITSET(zone_based_per_led_data.on_board_led_2.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_3.speedAndBrightnessFlags = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_3.colorFlags = BITSET(zone_based_per_led_data.on_board_led_3.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_4.speedAndBrightnessFlags = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_4.colorFlags = BITSET(zone_based_per_led_data.on_board_led_4.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_5.speedAndBrightnessFlags = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_5.colorFlags = BITSET(zone_based_per_led_data.on_board_led_5.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_6.speedAndBrightnessFlags = MSI_BRIGHTNESS_LEVEL_100 << 2 << 2;
-    zone_based_per_led_data.on_board_led_6.colorFlags = BITSET(zone_based_per_led_data.on_board_led_6.colorFlags, true, 7u);
+    zone_based_per_led_data.j_rgb_1.speedAndBrightnessFlags         = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.j_rgb_1.colorFlags                     |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.j_rainbow_1.speedAndBrightnessFlags     = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.j_rainbow_1.colorFlags                 |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led.speedAndBrightnessFlags    = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led.colorFlags                |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_1.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_1.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_2.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_2.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_3.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_3.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_4.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_4.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_5.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_5.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_6.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_6.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
     zone_based_per_led_data.save_data                               = 0;
 
     direct_mode = false;
@@ -93,8 +100,15 @@ void MSIMotherboard112Controller::SetMode
     bool            rainbow_color
     )
 {
+    /*-----------------------------------------------------*\
+    | Get the zone data pointer within the configuration    |
+    | data buffer                                           |
+    \*-----------------------------------------------------*/
     ZoneData* zone_data = GetZoneData(data, zone);
 
+    /*-----------------------------------------------------*\
+    | Return if zone is invalid                             |
+    \*-----------------------------------------------------*/
     if(zone_data == nullptr)
     {
         return;
@@ -103,19 +117,21 @@ void MSIMotherboard112Controller::SetMode
     if(zone <= MSI_ZONE_ON_BOARD_LED_0)
     {
         zone_data->effect                    = mode;
-        zone_data->speedAndBrightnessFlags   = (brightness << 2) | (speed & 0x03);
-        zone_data->colorFlags                = BITSET(zone_data->colorFlags, !rainbow_color, 7u);
+        zone_data->speedAndBrightnessFlags   = ((brightness << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT) & MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_MASK)
+                                             | ((speed << MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT)           & MSI_SPEED_BRIGHTNESS_FLAG_SPEED_MASK);
+        zone_data->colorFlags                = (rainbow_color ? (zone_data->colorFlags & ~MSI_COLOR_FLAG_USE_CUSTOM_COLOR)
+                                                              : (zone_data->colorFlags | MSI_COLOR_FLAG_USE_CUSTOM_COLOR));
         zone_data->padding                   = 0x00;
 
         if(mode > MSI_MODE_DOUBLE_FLASHING)
         {
-            zone_data->speedAndBrightnessFlags |= SYNC_SETTING_JRGB;
-            zone_data->colorFlags              |= SYNC_SETTING_ONBOARD;
+            zone_data->speedAndBrightnessFlags |= MSI_SPEED_BRIGHTNESS_FLAG_SYNC_SETTING_JRGB;
+            zone_data->colorFlags              |= MSI_COLOR_FLAG_SYNC_SETTING_ONBOARD;
         }
         else
         {
-            zone_data->speedAndBrightnessFlags &= ~SYNC_SETTING_JRGB;
-            zone_data->colorFlags              &= ~SYNC_SETTING_ONBOARD;
+            zone_data->speedAndBrightnessFlags &= ~MSI_SPEED_BRIGHTNESS_FLAG_SYNC_SETTING_JRGB;
+            zone_data->colorFlags              &= ~MSI_COLOR_FLAG_SYNC_SETTING_ONBOARD;
         }
     }
 
@@ -126,8 +142,10 @@ void MSIMotherboard112Controller::SetMode
         if(zone_data != nullptr)
         {
             zone_data->effect                    = mode;
-            zone_data->speedAndBrightnessFlags   = (brightness << 2) | (speed & 0x03);
-            zone_data->colorFlags                = BITSET(zone_data->colorFlags, !rainbow_color, 7u);
+            zone_data->speedAndBrightnessFlags   = ((brightness << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT) & MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_MASK)
+                                                 | ((speed << MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT)           & MSI_SPEED_BRIGHTNESS_FLAG_SPEED_MASK);
+            zone_data->colorFlags                = (rainbow_color ? (zone_data->colorFlags & ~MSI_COLOR_FLAG_USE_CUSTOM_COLOR)
+                                                                  : (zone_data->colorFlags | MSI_COLOR_FLAG_USE_CUSTOM_COLOR));
             zone_data->padding                   = 0x00;
         }
     }
@@ -201,8 +219,15 @@ void MSIMotherboard112Controller::SetZoneColor
     unsigned char   blu2
     )
 {
+    /*-----------------------------------------------------*\
+    | Get the zone data pointer within the configuration    |
+    | data buffer                                           |
+    \*-----------------------------------------------------*/
     ZoneData* zone_data = GetZoneData(data, zone);
 
+    /*-----------------------------------------------------*\
+    | Return if zone is invalid                             |
+    \*-----------------------------------------------------*/
     if(zone_data == nullptr)
     {
         return;
@@ -411,9 +436,9 @@ void MSIMotherboard112Controller::GetMode
     | Update pointers with data                             |
     \*-----------------------------------------------------*/
     mode            = (MSI_MODE)        zone_data->effect;
-    speed           = (MSI_SPEED)(zone_data->speedAndBrightnessFlags & 0x03);
-    brightness      = (MSI_BRIGHTNESS)((zone_data->speedAndBrightnessFlags >> 2) & 0x1F);
-    rainbow_color   = (zone_data->colorFlags & 0x80) == 0 ? true : false;
+    speed           = (MSI_SPEED)     ((zone_data->speedAndBrightnessFlags >> MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT)      & MSI_SPEED_BRIGHTNESS_FLAG_SPEED_MASK);
+    brightness      = (MSI_BRIGHTNESS)((zone_data->speedAndBrightnessFlags >> MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT) & MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_MASK);
+    rainbow_color   = ((zone_data->colorFlags & MSI_COLOR_FLAG_USE_CUSTOM_COLOR) == 0 ? false : true);
     color           = ToRGBColor(zone_data->color.R, zone_data->color.G, zone_data->color.B);
 }
 

Controllers/MSIMotherboardController/MSIMotherboard162Controller/MSIMotherboard162Controller.cpp

@@ -85,24 +85,32 @@ MSIMotherboard162Controller::MSIMotherboard162Controller(hid_device* handle, con
     location    = path;
     name        = dev_name;
 
-    if(dev)
-    {
+    /*-----------------------------------------------------*\
+    | Perform initial reads - get the controller's firmware |
+    | version and then read the controller's active         |
+    | configuration data                                    |
+    \*-----------------------------------------------------*/
     ReadFwVersion();
     ReadSettings();
-    }
 
     /*-----------------------------------------------------*\
-    | Initialize save flag                                  |
+    | The last byte of the packet is the save flag.  This   |
+    | byte is stored as a zero in the data flash, but is    |
+    | set to 1 at the protocol level to tell the firmware   |
+    | to save the active configuration to flash.            |
+    | Also set onboard zone to act as sync master for all   |
+    | of the onboard LEDs.                                  |
     \*-----------------------------------------------------*/
     data.save_data                  = 0;
-    data.on_board_led.colorFlags = 0x81;    // force MS bit of color flags to 1 to have expectd zone control
+    data.on_board_led.colorFlags    = MSI_COLOR_FLAG_USE_CUSTOM_COLOR | MSI_COLOR_FLAG_SYNC_SETTING_ONBOARD;
 
     /*-----------------------------------------------------*\
-    | Initialize zone based per LED data                    |
+    | Search for the board configuration matching this      |
+    | board.                                                |
     \*-----------------------------------------------------*/
     const mystic_light_162_config* board_config = nullptr;
 
-    for(std::size_t i = 0; i < NUMOF_CONFIGS; ++i)
+    for(std::size_t i = 0; i < NUMOF_CONFIGS; i++)
     {
         if (board_configs[i].pid == pid)
         {
@@ -111,6 +119,10 @@ MSIMotherboard162Controller::MSIMotherboard162Controller(hid_device* handle, con
         }
     }
 
+    /*-----------------------------------------------------*\
+    | Fill in the number of each zone type based on the     |
+    | board configuration                                   |
+    \*-----------------------------------------------------*/
     if(board_config != nullptr)
     {
         numof_onboard_leds = board_config->numof_onboard_leds;
@@ -137,8 +149,15 @@ void MSIMotherboard162Controller::SetMode
     bool            rainbow_color
     )
 {
+    /*-----------------------------------------------------*\
+    | Get the zone data pointer within the configuration    |
+    | data buffer                                           |
+    \*-----------------------------------------------------*/
     ZoneData* zone_data = GetZoneData(data, zone);
 
+    /*-----------------------------------------------------*\
+    | Return if zone is invalid                             |
+    \*-----------------------------------------------------*/
     if(zone_data == nullptr)
     {
         return;
@@ -147,19 +166,21 @@ void MSIMotherboard162Controller::SetMode
     if(zone <= MSI_ZONE_ON_BOARD_LED_0)
     {
         zone_data->effect                    = mode;
-        zone_data->speedAndBrightnessFlags   = (brightness << 2) | (speed & 0x03);
-        zone_data->colorFlags                = BITSET(zone_data->colorFlags, !rainbow_color, 7u);
+        zone_data->speedAndBrightnessFlags   = ((brightness << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT) & MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_MASK)
+                                             | ((speed << MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT)           & MSI_SPEED_BRIGHTNESS_FLAG_SPEED_MASK);
+        zone_data->colorFlags                = (rainbow_color ? (zone_data->colorFlags & ~MSI_COLOR_FLAG_USE_CUSTOM_COLOR)
+                                                              : (zone_data->colorFlags | MSI_COLOR_FLAG_USE_CUSTOM_COLOR));
         zone_data->padding                   = 0x00;
 
         if(mode > MSI_MODE_DOUBLE_FLASHING)
         {
-            zone_data->speedAndBrightnessFlags |= SYNC_SETTING_JRGB;
-            zone_data->colorFlags              |= SYNC_SETTING_ONBOARD;
+            zone_data->speedAndBrightnessFlags |= MSI_SPEED_BRIGHTNESS_FLAG_SYNC_SETTING_JRGB;
+            zone_data->colorFlags              |= MSI_COLOR_FLAG_SYNC_SETTING_ONBOARD;
         }
         else
         {
-            zone_data->speedAndBrightnessFlags &= ~SYNC_SETTING_JRGB;
-            zone_data->colorFlags              &= ~SYNC_SETTING_ONBOARD;
+            zone_data->speedAndBrightnessFlags &= ~MSI_SPEED_BRIGHTNESS_FLAG_SYNC_SETTING_JRGB;
+            zone_data->colorFlags              &= ~MSI_COLOR_FLAG_SYNC_SETTING_ONBOARD;
         }
     }
 
@@ -170,8 +191,10 @@ void MSIMotherboard162Controller::SetMode
         if(zone_data != nullptr)
         {
             zone_data->effect                    = mode;
-            zone_data->speedAndBrightnessFlags   = (brightness << 2) | (speed & 0x03);
-            zone_data->colorFlags                = BITSET(zone_data->colorFlags, !rainbow_color, 7u);
+            zone_data->speedAndBrightnessFlags   = ((brightness << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT) & MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_MASK)
+                                                 | ((speed << MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT)           & MSI_SPEED_BRIGHTNESS_FLAG_SPEED_MASK);
+            zone_data->colorFlags                = (rainbow_color ? (zone_data->colorFlags & ~MSI_COLOR_FLAG_USE_CUSTOM_COLOR)
+                                                                  : (zone_data->colorFlags | MSI_COLOR_FLAG_USE_CUSTOM_COLOR));
             zone_data->padding                   = 0x00;
         }
     }
@@ -238,8 +261,15 @@ void MSIMotherboard162Controller::SetZoneColor
     unsigned char   blu2
     )
 {
+    /*-----------------------------------------------------*\
+    | Get the zone data pointer within the configuration    |
+    | data buffer                                           |
+    \*-----------------------------------------------------*/
     ZoneData* zone_data = GetZoneData(data, zone);
 
+    /*-----------------------------------------------------*\
+    | Return if zone is invalid                             |
+    \*-----------------------------------------------------*/
     if(zone_data == nullptr)
     {
         return;
@@ -432,9 +462,9 @@ void MSIMotherboard162Controller::GetMode
     | Update pointers with data                             |
     \*-----------------------------------------------------*/
     mode            = (MSI_MODE)        zone_data->effect;
-    speed           = (MSI_SPEED)(zone_data->speedAndBrightnessFlags & 0x03);
-    brightness      = (MSI_BRIGHTNESS)((zone_data->speedAndBrightnessFlags >> 2) & 0x1F);
-    rainbow_color   = (zone_data->colorFlags & 0x80) == 0 ? true : false;
+    speed           = (MSI_SPEED)     ((zone_data->speedAndBrightnessFlags >> MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT)      & MSI_SPEED_BRIGHTNESS_FLAG_SPEED_MASK);
+    brightness      = (MSI_BRIGHTNESS)((zone_data->speedAndBrightnessFlags >> MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT) & MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_MASK);
+    rainbow_color   = ((zone_data->colorFlags & MSI_COLOR_FLAG_USE_CUSTOM_COLOR) == 0 ? false : true);
     color           = ToRGBColor(zone_data->color.R, zone_data->color.G, zone_data->color.B);
 }
 

Controllers/MSIMotherboardController/MSIMotherboard185Controller/MSIMotherboard185Controller.cpp

@@ -33,8 +33,8 @@ using namespace std::chrono_literals;
 #define JCORSAIR_MAX_LED_COUNT                  240
 
 #define MSI_DIRECT_MODE                         0x25
-#define PER_LED_BASIC_SYNC_MODE                 (0x80 | SYNC_SETTING_ONBOARD | SYNC_SETTING_JPIPE1 | SYNC_SETTING_JPIPE2)
-#define PER_LED_FULL_SYNC_MODE                  (PER_LED_BASIC_SYNC_MODE | SYNC_SETTING_JRAINBOW1 | SYNC_SETTING_JRAINBOW2 | SYNC_SETTING_JCORSAIR)
+#define PER_LED_BASIC_SYNC_MODE                 (MSI_COLOR_FLAG_USE_CUSTOM_COLOR | MSI_COLOR_FLAG_SYNC_SETTING_ONBOARD | MSI_COLOR_FLAG_SYNC_SETTING_JPIPE1 | MSI_COLOR_FLAG_SYNC_SETTING_JPIPE2)
+#define PER_LED_FULL_SYNC_MODE                  (PER_LED_BASIC_SYNC_MODE | MSI_COLOR_FLAG_SYNC_SETTING_JRAINBOW1 | MSI_COLOR_FLAG_SYNC_SETTING_JRAINBOW2 | MSI_COLOR_FLAG_SYNC_SETTING_JCORSAIR)
 
 struct mystic_light_185_config
 {
@@ -45,6 +45,7 @@ struct mystic_light_185_config
     int                                      numof_JRGBs;               // number of supported JRGB headers (used in per LED mode only)
     const std::vector<MSI_ZONE>*             supported_zones;           // pointer to vector of supported zones
     MSIMotherboard185Controller::DIRECT_MODE per_led_mode;              // type of direct mode support
+    unsigned char                            minimum_firmware_version;  // minimum required firmware version for this config (0 = all versions acceptable)
 };
 
 const std::vector<MSI_ZONE> all_zones =
@@ -257,104 +258,103 @@ const std::vector<MSI_ZONE> zones_set21 =
 
 static const mystic_light_185_config board_configs[] =
 {
-    { 0x7B93, 6,  1,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED },    // MPG X570 GAMING PRO CARBON WIFI
-    { 0x7C34, 0,  1,  1, 1, &zones_set8,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED },    // MEG X570 GODLIKE
-    { 0x7C35, 0,  1,  0, 1, &zones_set9,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED },    // MEG X570 ACE
-    { 0x7C36, 6,  1,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED },    // PRESTIGE X570 CREATION
-    { 0x7C37, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED },    // MPG X570 GAMING PLUS
-    { 0x7C56, 6,  0,  0, 1, &zones_set2,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG B550 GAMING PLUS
-    { 0x7C59, 0,  8,  0, 1, &zones_set9,  MSIMotherboard185Controller::DIRECT_MODE_DISABLED },      // CREATOR TRX40
-    { 0x7C60, 6,  0,  0, 1, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // TRX40-A PRO
-    { 0x7C67, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B365M MORTAR
-    { 0x7C71, 6,  6,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MEG Z490 ACE
-    { 0x7C73, 6,  4,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG Z490 GAMING CARBON WIFI
-    { 0x7C75, 6,  0,  0, 1, &zones_set2,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG Z490 GAMING PLUS
-    { 0x7C76, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_DISABLED },      // MPG Z490M GAMING EDGE
-    { 0x7C77, 0,  0,  0, 0, &zones_set14, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MEG Z490I UNIFY
-    { 0x7C79, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG Z490 GAMING EDGE WIFI
-    { 0x7C80, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG Z490 TOMAHAWK
-    { 0x7C02, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B450 TOMAHAWK MAX
-    { 0x7C81, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B460 TOMAHAWK
-    { 0x7C82, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B460M MORTAR WIFI
-    { 0x7C83, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_DISABLED },      // B460M PRO-VDH WIFI
-    { 0x7C84, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED },    // MAG X570 TOMAHAWK WIFI
-    { 0x7C86, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_DISABLED },      // MPG B460I GAMING EDGE
-    { 0x7C87, 6,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // B450M BAZOOKA MAX WIFI
-    { 0x7C90, 6,  4,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG B550 GAMING CARBON WIFI
-    { 0x7C91, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B550 TOMAHAWK
-    { 0x7C92, 6,  0,  0, 0, &zones_set6,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG B550I GAMING EDGE WIFI
-    { 0x7C94, 6,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B550M MORTAR
-    { 0x7C95, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // B550M PRO-VDH WIFI
-    { 0x7C98, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // Z490 PLUS
-    { 0x7D03, 0, 15, 18, 1, &zones_set8,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG Z590 GODLIKE
-    { 0x7D06, 4,  4,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG Z590 GAMING FORCE
-    { 0x7D07, 4,  5,  0, 2, &zones_set7,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG Z590 GAMING EDGE WIFI
-    { 0x7D08, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG Z590 TOMAHAWK
-    { 0x7D09, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // Z590-A PRO WIFI
-    { 0x7D13, 6,  0,  0, 1, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MEG B550 UNIFY
-    { 0x7D14, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // A520M PRO
-    { 0x7D15, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B560 TOMAHAWK WIFI
-    { 0x7D17, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B560M MORTAR
-    { 0x7D18, 6,  0,  0, 2, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B560M PRO-VDH
-    { 0x7D19, 6,  0,  0, 2, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG B560I GAMIING EDGE WIFI
-    { 0x7D20, 6,  0,  0, 2, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B560M PRO
-    { 0x7D25, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO Z690-A WIFI DDR4
-    { 0x7D27, 6,  0,  0, 2, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MEG Z690 ACE
-    { 0x7D28, 6,  0,  0, 1, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MEG Z690 UNIFY-X
-    { 0x7D29, 6,  0,  0, 0, &zones_set6,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MEG Z690I UNIFY
-    { 0x7D30, 6,  6,  0, 2, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG Z690 CARBON WIFI
-    { 0x7D31, 4,  8,  0, 2, &zones_set12, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG EDGE WIFI DDR4
-    { 0x7D32, 1,  0,  0, 1, &zones_set10, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG Z690 TOMAHAWK WIFI DDR4
-    { 0x7D33, 6,  0,  0, 2, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO Z790-VC WIFI
-    { 0x7D36, 6,  0,  0, 2, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO Z690-P DDR4
-    { 0x7D37, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO B760M-VC WIFI (MS-7D37) - fans on JRAINBOW2
-    { 0x7D38, 0,  0,  0, 1, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MEG Z590 UNIFY-X
-    { 0x7D40, 0,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG B760i EDGE WIFI DDR4
-    { 0x7D41, 6,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B660M TOMAHAWK WIFI DDR4
-    { 0x7D42, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B660 MORTAR WIFI DDR4
-    { 0x7D43, 0,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO B660M-A WIFI DDR4
-    { 0x7D46, 0,  1,  1, 0, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO H610M-G DDR4
-    { 0x7D50, 6, 12,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MEG X570S ACE MAX
-    { 0x7D51, 6,  0,  0, 2, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MEG X570S UNIFY-X MAX
-    { 0x7D52, 6, 14,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG X570S CARBON EK X
-    { 0x7D53, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG X570S EDGE MAX WIFI
-    { 0x7D54, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG X570S TOMAHAWK MAX WIFI
-    { 0x7D59, 0,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO B660-A DDR4
-    { 0x7D67, 0,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO X670-P WIFI
-    { 0x7D69, 9,  2,  4, 1, &zones_set15, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MEG X670E ACE
-    { 0x7D70, 0,  6,  0, 1, &zones_set9,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG X670E Carbon WIFI
-    { 0x7D73, 1,  0,  0, 0, &zones_set6,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG B650I EDGE WIFI
-    { 0x7D74, 0,  6,  0, 1, &zones_set18, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG B650 CARBON WIFI
-    { 0x7D75, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B650 TOMAHAWK WIFI
-    { 0x7D76, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B650M MORTAR WIFI
-    { 0x7D77, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO B650M-A WIFI
-    { 0x7D78, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO B650-P WIFI
-    { 0x7D86, 0, 18,  4, 1, &zones_set16, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MEG Z790 ACE
-    { 0x7D88, 0,  0,  0, 1, &zones_set20, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG Z790-S WIFI
-    { 0x7D89, 0,  6,  0, 1, &zones_set18, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG Z790 CARBON WIFI
-    { 0x7D90, 0,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // B760M BOMBER DDR4
-    { 0x7D91, 1,  0,  0, 1, &zones_set10, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG Z790 TOMAHAWK WIFI
-    { 0x7D93, 6,  0,  0, 1, &zones_set2,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // Z790 GAMING PRO WIFI
-    { 0x7D96, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B760 TOMAHAWK WIFI DDR5
-    { 0x7D97, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B660 MORTAR MAX WIFI DDR4
-    { 0x7D98, 0,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO B760-P WIFI DDR4
-    { 0x7D99, 6,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO B760M-A WIFI DDR4
-    { 0x7E01, 0,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG B760M MORTAR MAX
-    { 0x7E03, 6,  0,  0, 0, &zones_set6,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG Z790I EDGE WIFI
-    { 0x7E06, 0,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO Z790-P WIFI DDR4
-    { 0x7E07, 0,  0,  0, 2, &zones_set10, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO Z790-A WIFI DDR4
-    { 0x7E09, 0,  0,  0, 0, &zones_set19, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // B650M PROJECT ZERO
-    { 0x7E10, 0,  6,  0, 2, &zones_set17, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MPG B650 EDGE WIFI
-    { 0x7E12, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG X670E TOMAHAWK WIFI
-    { 0x0076, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // MAG X670E TOMAHAWK WIFI (Common PID)
-    { 0x7E16, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // X670E GAMING PLUS WIFI
-    { 0x7E24, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // B650M GAMING PLUS WIFI
-    { 0x7E26, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // B650 GAMING PLUS WIFI
-    { 0x7E27, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED },       // PRO B650M-P
-    { 0x7E28, 6,  0,  0, 2, &zones_set21, MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED },    // MSI PRO A620M-B (MS-7E28)
+    { 0x7B93, 6,  1,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED,  0 },    // MPG X570 GAMING PRO CARBON WIFI
+    { 0x7C34, 0,  1,  1, 1, &zones_set8,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED,  0 },    // MEG X570 GODLIKE
+    { 0x7C35, 0,  1,  0, 1, &zones_set9,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED,  0 },    // MEG X570 ACE
+    { 0x7C36, 6,  1,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED,  0 },    // PRESTIGE X570 CREATION
+    { 0x7C37, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED,  0 },    // MPG X570 GAMING PLUS
+    { 0x7C56, 6,  0,  0, 1, &zones_set2,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     6 },    // MPG B550 GAMING PLUS
+    { 0x7C59, 0,  8,  0, 1, &zones_set9,  MSIMotherboard185Controller::DIRECT_MODE_DISABLED,    0 },    // CREATOR TRX40
+    { 0x7C60, 6,  0,  0, 1, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // TRX40-A PRO
+    { 0x7C67, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B365M MORTAR
+    { 0x7C71, 6,  6,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MEG Z490 ACE
+    { 0x7C73, 6,  4,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG Z490 GAMING CARBON WIFI
+    { 0x7C75, 6,  0,  0, 1, &zones_set2,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG Z490 GAMING PLUS
+    { 0x7C76, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_DISABLED,    0 },    // MPG Z490M GAMING EDGE
+    { 0x7C77, 0,  0,  0, 0, &zones_set14, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MEG Z490I UNIFY
+    { 0x7C79, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG Z490 GAMING EDGE WIFI
+    { 0x7C80, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG Z490 TOMAHAWK
+    { 0x7C02, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B450 TOMAHAWK MAX
+    { 0x7C81, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B460 TOMAHAWK
+    { 0x7C82, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B460M MORTAR WIFI
+    { 0x7C83, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_DISABLED,    0 },    // B460M PRO-VDH WIFI
+    { 0x7C84, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED,  0 },    // MAG X570 TOMAHAWK WIFI
+    { 0x7C86, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_DISABLED,    0 },    // MPG B460I GAMING EDGE
+    { 0x7C87, 6,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // B450M BAZOOKA MAX WIFI
+    { 0x7C90, 6,  4,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG B550 GAMING CARBON WIFI
+    { 0x7C91, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B550 TOMAHAWK
+    { 0x7C92, 6,  0,  0, 0, &zones_set6,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG B550I GAMING EDGE WIFI
+    { 0x7C94, 6,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B550M MORTAR
+    { 0x7C95, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // B550M PRO-VDH WIFI
+    { 0x7C98, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // Z490 PLUS
+    { 0x7D03, 0, 15, 18, 1, &zones_set8,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG Z590 GODLIKE
+    { 0x7D06, 4,  4,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG Z590 GAMING FORCE
+    { 0x7D07, 4,  5,  0, 2, &zones_set7,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG Z590 GAMING EDGE WIFI
+    { 0x7D08, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG Z590 TOMAHAWK
+    { 0x7D09, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // Z590-A PRO WIFI
+    { 0x7D13, 6,  0,  0, 1, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MEG B550 UNIFY
+    { 0x7D14, 6,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // A520M PRO
+    { 0x7D15, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B560 TOMAHAWK WIFI
+    { 0x7D17, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B560M MORTAR
+    { 0x7D18, 6,  0,  0, 2, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B560M PRO-VDH
+    { 0x7D19, 6,  0,  0, 2, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG B560I GAMIING EDGE WIFI
+    { 0x7D20, 6,  0,  0, 2, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B560M PRO
+    { 0x7D25, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO Z690-A WIFI DDR4
+    { 0x7D27, 6,  0,  0, 2, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MEG Z690 ACE
+    { 0x7D28, 6,  0,  0, 1, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MEG Z690 UNIFY-X
+    { 0x7D29, 6,  0,  0, 0, &zones_set6,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MEG Z690I UNIFY
+    { 0x7D30, 6,  6,  0, 2, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG Z690 CARBON WIFI
+    { 0x7D31, 4,  8,  0, 2, &zones_set12, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG EDGE WIFI DDR4
+    { 0x7D32, 1,  0,  0, 1, &zones_set10, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG Z690 TOMAHAWK WIFI DDR4
+    { 0x7D33, 6,  0,  0, 2, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO Z790-VC WIFI
+    { 0x7D36, 6,  0,  0, 2, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO Z690-P DDR4
+    { 0x7D37, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO B760M-VC WIFI (MS-7D37) - fans on JRAINBOW2
+    { 0x7D38, 0,  0,  0, 1, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MEG Z590 UNIFY-X
+    { 0x7D40, 0,  0,  0, 1, &zones_set5,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG B760i EDGE WIFI DDR4
+    { 0x7D41, 6,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B660M TOMAHAWK WIFI DDR4
+    { 0x7D42, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B660 MORTAR WIFI DDR4
+    { 0x7D43, 0,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO B660M-A WIFI DDR4
+    { 0x7D46, 0,  1,  1, 0, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO H610M-G DDR4
+    { 0x7D50, 6, 12,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MEG X570S ACE MAX
+    { 0x7D51, 6,  0,  0, 2, &zones_set1,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MEG X570S UNIFY-X MAX
+    { 0x7D52, 6, 14,  0, 1, &zones_set3,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG X570S CARBON EK X
+    { 0x7D53, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG X570S EDGE MAX WIFI
+    { 0x7D54, 6,  0,  0, 2, &zones_set0,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG X570S TOMAHAWK MAX WIFI
+    { 0x7D59, 0,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO B660-A DDR4
+    { 0x7D67, 0,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO X670-P WIFI
+    { 0x7D69, 9,  2,  4, 1, &zones_set15, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MEG X670E ACE
+    { 0x7D70, 0,  6,  0, 1, &zones_set9,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG X670E Carbon WIFI
+    { 0x7D73, 1,  0,  0, 0, &zones_set6,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG B650I EDGE WIFI
+    { 0x7D74, 0,  6,  0, 1, &zones_set18, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG B650 CARBON WIFI
+    { 0x7D75, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B650 TOMAHAWK WIFI
+    { 0x7D76, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B650M MORTAR WIFI
+    { 0x7D77, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO B650M-A WIFI
+    { 0x7D78, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO B650-P WIFI
+    { 0x7D86, 0, 18,  4, 1, &zones_set16, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MEG Z790 ACE
+    { 0x7D88, 0,  0,  0, 1, &zones_set20, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG Z790-S WIFI
+    { 0x7D89, 0,  6,  0, 1, &zones_set18, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG Z790 CARBON WIFI
+    { 0x7D90, 0,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // B760M BOMBER DDR4
+    { 0x7D91, 1,  0,  0, 1, &zones_set10, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG Z790 TOMAHAWK WIFI
+    { 0x7D93, 6,  0,  0, 1, &zones_set2,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // Z790 GAMING PRO WIFI
+    { 0x7D96, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B760 TOMAHAWK WIFI DDR5
+    { 0x7D97, 6,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B660 MORTAR MAX WIFI DDR4
+    { 0x7D98, 0,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO B760-P WIFI DDR4
+    { 0x7D99, 6,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO B760M-A WIFI DDR4
+    { 0x7E01, 0,  0,  0, 1, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG B760M MORTAR MAX
+    { 0x7E03, 6,  0,  0, 0, &zones_set6,  MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG Z790I EDGE WIFI
+    { 0x7E06, 0,  0,  0, 2, &zones_set11, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO Z790-P WIFI DDR4
+    { 0x7E07, 0,  0,  0, 2, &zones_set10, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO Z790-A WIFI DDR4
+    { 0x7E09, 0,  0,  0, 0, &zones_set19, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // B650M PROJECT ZERO
+    { 0x7E10, 0,  6,  0, 2, &zones_set17, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MPG B650 EDGE WIFI
+    { 0x7E12, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG X670E TOMAHAWK WIFI
+    { 0x0076, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // MAG X670E TOMAHAWK WIFI (Common PID)
+    { 0x7E16, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // X670E GAMING PLUS WIFI
+    { 0x7E24, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // B650M GAMING PLUS WIFI
+    { 0x7E26, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // B650 GAMING PLUS WIFI
+    { 0x7E27, 0,  0,  0, 2, &zones_set13, MSIMotherboard185Controller::DIRECT_MODE_PER_LED,     0 },    // PRO B650M-P
+    { 0x7E28, 6,  0,  0, 2, &zones_set21, MSIMotherboard185Controller::DIRECT_MODE_ZONE_BASED,  0 },    // MSI PRO A620M-B (MS-7E28)
 };
 
-
 FeaturePacket_185 enable_per_led_msg;
 
 Color* per_led_onboard_leds;
@@ -370,19 +370,26 @@ MSIMotherboard185Controller::MSIMotherboard185Controller(hid_device* handle, con
     dev             = handle;
     location        = path;
     name            = dev_name;
+    version_invalid = false;
 
-    if(dev)
-    {
+    /*-----------------------------------------------------*\
+    | Read the controller's firmware version                |
+    \*-----------------------------------------------------*/
     ReadFwVersion();
-        ReadSettings();
-    }
 
+    /*-----------------------------------------------------*\
+    | Common PID boards embed their virtual PID in the      |
+    | serial number, extract it                             |
+    \*-----------------------------------------------------*/
     if(pid == MSI_USB_PID_COMMON)
     {
         std::string pidStr(GetSerial().substr(0, 4));
         pid = std::stoi(pidStr, nullptr, 16);
     }
 
+    /*-----------------------------------------------------*\
+    | Determine if this board has mixed-mode support        |
+    \*-----------------------------------------------------*/
     mixed_mode_support = false;
 
     if(pid >= 0x7D03)
@@ -391,14 +398,23 @@ MSIMotherboard185Controller::MSIMotherboard185Controller(hid_device* handle, con
     }
 
     /*-----------------------------------------------------*\
-    | Initialize save flag and some static settings         |
+    | The last byte of the packet is the save flag.  This   |
+    | byte is stored as a zero in the data flash, but is    |
+    | set to 1 at the protocol level to tell the firmware   |
+    | to save the active configuration to flash.            |
+    | Also set onboard zone to act as sync master for all   |
+    | of the onboard LEDs.                                  |
     \*-----------------------------------------------------*/
     data.save_data                  = 0;
-    data.on_board_led.colorFlags = 0x80 | SYNC_SETTING_ONBOARD; // always enable onboard sync flag to have expected zone control
+    data.on_board_led.colorFlags    = MSI_COLOR_FLAG_USE_CUSTOM_COLOR | MSI_COLOR_FLAG_SYNC_SETTING_ONBOARD;
 
+    /*-----------------------------------------------------*\
+    | Search for the board configuration matching this      |
+    | board.                                                |
+    \*-----------------------------------------------------*/
     const mystic_light_185_config* board_config = nullptr;
 
-    for(std::size_t i = 0; i < NUMOF_CONFIGS; ++i)
+    for(std::size_t i = 0; i < NUMOF_CONFIGS; i++)
     {
         if(board_configs[i].pid == pid)
         {
@@ -407,8 +423,22 @@ MSIMotherboard185Controller::MSIMotherboard185Controller(hid_device* handle, con
         }
     }
 
+    /*-----------------------------------------------------*\
+    | Fill in the number of each zone type based on the     |
+    | board configuration                                   |
+    \*-----------------------------------------------------*/
     if(board_config != nullptr)
     {
+        /*-------------------------------------------------*\
+        | If the firmware version is below the minimum, set |
+        | invalid version flag and return                   |
+        \*-------------------------------------------------*/
+        if(version_APROM_val < board_config->minimum_firmware_version)
+        {
+            version_invalid = true;
+            return;
+        }
+
         numof_onboard_leds  = board_config->numof_onboard_leds;
         numof_pipe1_leds    = board_config->numof_pipe1_leds;
         numof_pipe2_leds    = board_config->numof_pipe2_leds;
@@ -426,6 +456,11 @@ MSIMotherboard185Controller::MSIMotherboard185Controller(hid_device* handle, con
         per_led_mode        = DIRECT_MODE_DISABLED;
     }
 
+    /*-----------------------------------------------------*\
+    | Read the controller's active configuration data       |
+    \*-----------------------------------------------------*/
+    ReadSettings();
+
     /*-----------------------------------------------------*\
     | Initialize per-LED data                               |
     \*-----------------------------------------------------*/
@@ -500,7 +535,7 @@ MSIMotherboard185Controller::MSIMotherboard185Controller(hid_device* handle, con
     enable_per_led_msg.j_corsair_outerll120.speedAndBrightnessFlags = 0x28;
     enable_per_led_msg.j_corsair_outerll120.colorFlags              = 0x80;
     enable_per_led_msg.on_board_led.effect                          = MSI_DIRECT_MODE;
-    enable_per_led_msg.on_board_led.speedAndBrightnessFlags         = 0x29 | SYNC_SETTING_JRGB;
+    enable_per_led_msg.on_board_led.speedAndBrightnessFlags         = 0x29 | MSI_SPEED_BRIGHTNESS_FLAG_SYNC_SETTING_JRGB;
     enable_per_led_msg.on_board_led.colorFlags                      = PER_LED_FULL_SYNC_MODE;
     enable_per_led_msg.on_board_led_1.speedAndBrightnessFlags       = 0x28;
     enable_per_led_msg.on_board_led_1.colorFlags                    = 0x80;
@@ -526,41 +561,42 @@ MSIMotherboard185Controller::MSIMotherboard185Controller(hid_device* handle, con
     /*-----------------------------------------------------*\
     | Initialize zone based per LED data                    |
     \*-----------------------------------------------------*/
-    zone_based_per_led_data.j_rgb_1.speedAndBrightnessFlags         = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.j_rgb_1.colorFlags                      = BITSET(zone_based_per_led_data.j_rgb_1.colorFlags, true, 7u);
-    zone_based_per_led_data.j_pipe_1.speedAndBrightnessFlags        = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.j_pipe_1.colorFlags                     = BITSET(zone_based_per_led_data.j_pipe_1.colorFlags, true, 7u);
-    zone_based_per_led_data.j_pipe_2.speedAndBrightnessFlags        = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.j_pipe_2.colorFlags                     = BITSET(zone_based_per_led_data.j_pipe_2.colorFlags, true, 7u);
-    zone_based_per_led_data.j_rainbow_1.speedAndBrightnessFlags     = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.j_rainbow_1.colorFlags                  = BITSET(zone_based_per_led_data.j_rainbow_1.colorFlags, true, 7u);
-    zone_based_per_led_data.j_rainbow_2.speedAndBrightnessFlags     = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.j_rainbow_2.colorFlags                  = BITSET(zone_based_per_led_data.j_rainbow_2.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led.speedAndBrightnessFlags    = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led.colorFlags                 = BITSET(zone_based_per_led_data.on_board_led.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_1.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_1.colorFlags               = BITSET(zone_based_per_led_data.on_board_led_1.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_2.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_2.colorFlags               = BITSET(zone_based_per_led_data.on_board_led_2.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_3.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_3.colorFlags               = BITSET(zone_based_per_led_data.on_board_led_3.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_4.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_4.colorFlags               = BITSET(zone_based_per_led_data.on_board_led_4.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_5.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_5.colorFlags               = BITSET(zone_based_per_led_data.on_board_led_5.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_6.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << 2 << 2;
-    zone_based_per_led_data.on_board_led_6.colorFlags               = BITSET(zone_based_per_led_data.on_board_led_6.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_7.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100;
-    zone_based_per_led_data.on_board_led_7.colorFlags               = BITSET(zone_based_per_led_data.on_board_led_7.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_8.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_8.colorFlags               = BITSET(zone_based_per_led_data.on_board_led_8.colorFlags, true, 7u);
-    zone_based_per_led_data.on_board_led_9.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.on_board_led_9.colorFlags               = BITSET(zone_based_per_led_data.on_board_led_9.colorFlags, true, 7u);
-    zone_based_per_led_data.j_rgb_2.speedAndBrightnessFlags         = MSI_BRIGHTNESS_LEVEL_100 << 2;
-    zone_based_per_led_data.j_rgb_2.colorFlags                      = BITSET(zone_based_per_led_data.j_rgb_2.colorFlags, true, 7u);
+    zone_based_per_led_data.j_rgb_1.speedAndBrightnessFlags         = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.j_rgb_1.colorFlags                     |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.j_pipe_1.speedAndBrightnessFlags        = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.j_pipe_1.colorFlags                    |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.j_pipe_2.speedAndBrightnessFlags        = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.j_pipe_2.colorFlags                    |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.j_rainbow_1.speedAndBrightnessFlags     = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.j_rainbow_1.colorFlags                 |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.j_rainbow_2.speedAndBrightnessFlags     = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.j_rainbow_2.colorFlags                 |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led.speedAndBrightnessFlags    = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led.colorFlags                |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_1.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_1.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_2.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_2.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_3.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_3.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_4.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_4.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_5.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_5.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_6.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_6.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_7.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_7.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_8.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_8.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.on_board_led_9.speedAndBrightnessFlags  = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.on_board_led_9.colorFlags              |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
+    zone_based_per_led_data.j_rgb_2.speedAndBrightnessFlags         = MSI_BRIGHTNESS_LEVEL_100 << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT;
+    zone_based_per_led_data.j_rgb_2.colorFlags                     |= MSI_COLOR_FLAG_USE_CUSTOM_COLOR;
     zone_based_per_led_data.save_data                               = 0;
 
     direct_mode             = false;
+    direct_mode_configured  = false;
     sync_direct_mode        = true;
 }
 
@@ -569,6 +605,11 @@ MSIMotherboard185Controller::~MSIMotherboard185Controller()
     hid_close(dev);
 }
 
+bool MSIMotherboard185Controller::GetFirmwareVersionInvalid()
+{
+    return(version_invalid);
+}
+
 void MSIMotherboard185Controller::SetMode
     (
     MSI_ZONE        zone,
@@ -583,40 +624,74 @@ void MSIMotherboard185Controller::SetMode
         return;
     }
 
+    /*-----------------------------------------------------*\
+    | Get the zone data pointer within the configuration    |
+    | data buffer                                           |
+    \*-----------------------------------------------------*/
     ZoneData* zone_data = GetZoneData(data, zone);
 
+    /*-----------------------------------------------------*\
+    | Return if zone is invalid                             |
+    \*-----------------------------------------------------*/
     if(zone_data == nullptr)
     {
         return;
     }
 
+    /*-----------------------------------------------------*\
+    | Update the zone's mode and mode parameters            |
+    \*-----------------------------------------------------*/
     zone_data->effect                    = mode;
-    zone_data->speedAndBrightnessFlags   = (brightness << 2) | (speed & 0x03);
-    zone_data->colorFlags                = BITSET(zone_data->colorFlags, !rainbow_color, 7u);
+    zone_data->speedAndBrightnessFlags   = ((brightness << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT) & MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_MASK)
+                                         | ((speed << MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT)           & MSI_SPEED_BRIGHTNESS_FLAG_SPEED_MASK);
+    zone_data->colorFlags                = (rainbow_color ? (zone_data->colorFlags & ~MSI_COLOR_FLAG_USE_CUSTOM_COLOR)
+                                                          : (zone_data->colorFlags | MSI_COLOR_FLAG_USE_CUSTOM_COLOR));
+
+    /*-----------------------------------------------------*\
+    | J_RAINBOW_3 zone needs padding of 4                   |
+    \*-----------------------------------------------------*/
     zone == MSI_ZONE_J_RAINBOW_3 ? zone_data->padding = 4 : zone_data->padding = 0;
 
+    /*-----------------------------------------------------*\
+    | Get the zone data pointer to the on-board LED 0 zone  |
+    \*-----------------------------------------------------*/
     ZoneData* on_board_zone = GetZoneData(data, MSI_ZONE_ON_BOARD_LED_0);
 
+    /*-----------------------------------------------------*\
+    | If the zone is JRGB or JPIPE and the board has no     |
+    | onboard LEDs, set the onboard zone to this zone's     |
+    | settings                                              |
+    \*-----------------------------------------------------*/
     if(no_onboards && ((zone == MSI_ZONE_J_RGB_1) || (zone == MSI_ZONE_J_RGB_2) || (zone == MSI_ZONE_J_PIPE_1) || (zone == MSI_ZONE_J_PIPE_2)))
     {
         on_board_zone->effect                   =  zone_data->effect;
-        on_board_zone->speedAndBrightnessFlags =  zone_data->speedAndBrightnessFlags;
-        on_board_zone->colorFlags              =  zone_data->colorFlags;
-        on_board_zone->colorFlags              |= SYNC_SETTING_ONBOARD;
+        zone_data->speedAndBrightnessFlags      = ((brightness << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT) & MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_MASK)
+                                                | ((speed << MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT)           & MSI_SPEED_BRIGHTNESS_FLAG_SPEED_MASK);
+        zone_data->colorFlags                   = (rainbow_color ? (zone_data->colorFlags & ~MSI_COLOR_FLAG_USE_CUSTOM_COLOR)
+                                                                 : (zone_data->colorFlags | MSI_COLOR_FLAG_USE_CUSTOM_COLOR));
+        on_board_zone->colorFlags              |= MSI_COLOR_FLAG_SYNC_SETTING_ONBOARD;
         on_board_zone->padding                  = 0x00;
     }
 
+    /*-----------------------------------------------------*\
+    | For modes above MSI_MODE_LIGHTNING, set the onboard   |
+    | zone to sync with JRGB, JPIPE1, and JPIPE2            |
+    \*-----------------------------------------------------*/
     if(mode > MSI_MODE_LIGHTNING)
     {
-        on_board_zone->speedAndBrightnessFlags |= SYNC_SETTING_JRGB;
-        on_board_zone->colorFlags              |= (SYNC_SETTING_JPIPE1 | SYNC_SETTING_JPIPE2);
+        on_board_zone->speedAndBrightnessFlags |= MSI_SPEED_BRIGHTNESS_FLAG_SYNC_SETTING_JRGB;
+        on_board_zone->colorFlags              |= (MSI_COLOR_FLAG_SYNC_SETTING_JPIPE1 | MSI_COLOR_FLAG_SYNC_SETTING_JPIPE2);
     }
     else
     {
-        on_board_zone->speedAndBrightnessFlags &= ~SYNC_SETTING_JRGB;
-        on_board_zone->colorFlags              &= ~(SYNC_SETTING_JPIPE1 | SYNC_SETTING_JPIPE2);
+        on_board_zone->speedAndBrightnessFlags &= ~MSI_SPEED_BRIGHTNESS_FLAG_SYNC_SETTING_JRGB;
+        on_board_zone->colorFlags              &= ~(MSI_COLOR_FLAG_SYNC_SETTING_JPIPE1 | MSI_COLOR_FLAG_SYNC_SETTING_JPIPE2);
     }
 
+    /*-----------------------------------------------------*\
+    | For modes at or below MSI_MODE_LIGHTNING, set all     |
+    | onboard LED zones to match onboard LED zone 0         |
+    \*-----------------------------------------------------*/
     if((zone == MSI_ZONE_ON_BOARD_LED_0) && (mode <= MSI_MODE_LIGHTNING))
     {
         for(int i = 0; i < numof_onboard_leds; ++i)
@@ -626,8 +701,10 @@ void MSIMotherboard185Controller::SetMode
             if(zone_data != nullptr)
             {
                 zone_data->effect                    = mode;
-                zone_data->speedAndBrightnessFlags   = (brightness << 2) | (speed & 0x03);
-                zone_data->colorFlags                = BITSET(zone_data->colorFlags, !rainbow_color, 7u);
+                zone_data->speedAndBrightnessFlags   = ((brightness << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT) & MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_MASK)
+                                                     | ((speed << MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT)           & MSI_SPEED_BRIGHTNESS_FLAG_SPEED_MASK);
+                zone_data->colorFlags                = (rainbow_color ? (zone_data->colorFlags & ~MSI_COLOR_FLAG_USE_CUSTOM_COLOR)
+                                                                      : (zone_data->colorFlags | MSI_COLOR_FLAG_USE_CUSTOM_COLOR));
                 zone_data->padding                   = 0x00;
             }
         }
@@ -682,6 +759,46 @@ bool MSIMotherboard185Controller::Update
     {
         if(per_led_mode == DIRECT_MODE_PER_LED)
         {
+            /*---------------------------------------------*\
+            | Skip sending update if there are no LEDs      |
+            | configured                                    |
+            \*---------------------------------------------*/
+            bool has_active_per_led_data = false;
+
+            if(!no_onboards)
+            {
+                has_active_per_led_data = true;
+            }
+            if(!no_jrainbow1)
+            {
+                has_active_per_led_data = true;
+            }
+            if(!no_jrainbow2)
+            {
+                has_active_per_led_data = true;
+            }
+            if(!no_jcorsair)
+            {
+                has_active_per_led_data = true;
+            }
+
+            if(!has_active_per_led_data)
+            {
+                return false;
+            }
+
+            /*---------------------------------------------*\
+            | Ensure the enable per-LED mode message has    |
+            | been sent before sending the per-LED data     |
+            \*---------------------------------------------*/
+            if(!direct_mode_configured)
+            {
+                if(!SelectPerLedProtocol())
+                {
+                    return false;
+                }
+            }
+
             if(sync_direct_mode)
             {
                 return(hid_send_feature_report(dev, (unsigned char*)&per_led_data_onboard_and_sync, sizeof(per_led_data_onboard_and_sync)) == sizeof(per_led_data_onboard_and_sync));
@@ -690,17 +807,17 @@ bool MSIMotherboard185Controller::Update
             {
                 if(!no_jrainbow1)
                 {
-                    (void)hid_send_feature_report(dev, (unsigned char*)&per_led_data_jrainbow1, sizeof(per_led_data_jrainbow1));
+                    hid_send_feature_report(dev, (unsigned char*)&per_led_data_jrainbow1, sizeof(per_led_data_jrainbow1));
                     std::this_thread::sleep_for(13ms);
                 }
                 if(!no_jrainbow2)
                 {
-                    (void)hid_send_feature_report(dev, (unsigned char*)&per_led_data_jrainbow2, sizeof(per_led_data_jrainbow2));
+                    hid_send_feature_report(dev, (unsigned char*)&per_led_data_jrainbow2, sizeof(per_led_data_jrainbow2));
                     std::this_thread::sleep_for(13ms);
                 }
                 if(!no_jcorsair)
                 {
-                    (void)hid_send_feature_report(dev, (unsigned char*)&per_led_data_jcorsair, sizeof(per_led_data_jcorsair));
+                    hid_send_feature_report(dev, (unsigned char*)&per_led_data_jcorsair, sizeof(per_led_data_jcorsair));
                     std::this_thread::sleep_for(13ms);
                 }
                 return(hid_send_feature_report(dev, (unsigned char*)&per_led_data_onboard_and_sync, sizeof(per_led_data_onboard_and_sync)) == sizeof(per_led_data_onboard_and_sync));
@@ -748,13 +865,23 @@ void MSIMotherboard185Controller::SetZoneColor
         return;
     }
 
+    /*-----------------------------------------------------*\
+    | Get the zone data pointer within the configuration    |
+    | data buffer                                           |
+    \*-----------------------------------------------------*/
     ZoneData* zone_data = GetZoneData(data, zone);
 
+    /*-----------------------------------------------------*\
+    | Return if zone is invalid                             |
+    \*-----------------------------------------------------*/
     if(zone_data == nullptr)
     {
         return;
     }
 
+    /*-----------------------------------------------------*\
+    | Set the colors in the zone data                       |
+    \*-----------------------------------------------------*/
     zone_data->color.R  = red1;
     zone_data->color.G  = grn1;
     zone_data->color.B  = blu1;
@@ -762,6 +889,11 @@ void MSIMotherboard185Controller::SetZoneColor
     zone_data->color2.G = grn2;
     zone_data->color2.B = blu2;
 
+    /*-----------------------------------------------------*\
+    | If the zone is JRGB or JPIPE and the board has no     |
+    | onboard LEDs, set the onboard zone's colors to this   |
+    | zone's colors                                         |
+    \*-----------------------------------------------------*/
     if(no_onboards && ((zone == MSI_ZONE_J_RGB_1) || (zone == MSI_ZONE_J_RGB_2) || (zone == MSI_ZONE_J_PIPE_1) || (zone == MSI_ZONE_J_PIPE_2)))
     {
         ZoneData* on_board_zone = GetZoneData(data, MSI_ZONE_ON_BOARD_LED_0);
@@ -774,6 +906,10 @@ void MSIMotherboard185Controller::SetZoneColor
         on_board_zone->color2.B = blu2;
     }
 
+    /*-----------------------------------------------------*\
+    | Set all onboard LED zones' colors to match onboard    |
+    | LED 0                                                 |
+    \*-----------------------------------------------------*/
     if(zone == MSI_ZONE_ON_BOARD_LED_0)
     {
         for(int i = 0; i < numof_onboard_leds; ++i)
@@ -802,6 +938,10 @@ void MSIMotherboard185Controller::SetLedColor
     unsigned char   blu
     )
 {
+    /*-----------------------------------------------------*\
+    | If this board supports Per-LED direct mode, update    |
+    | the per-LED packet buffers                            |
+    \*-----------------------------------------------------*/
     if(per_led_mode == DIRECT_MODE_PER_LED)
     {
         Color* zone_data = GetPerLedZoneData(zone);
@@ -837,6 +977,9 @@ void MSIMotherboard185Controller::SetLedColor
             }
         }
     }
+    /*-----------------------------------------------------*\
+    | Otherwise, colors are set per zone.                   |
+    \*-----------------------------------------------------*/
     else
     {
         if(((zone == MSI_ZONE_J_RAINBOW_1) || (zone == MSI_ZONE_J_RAINBOW_2) || (zone == MSI_ZONE_J_PIPE_1) || (zone == MSI_ZONE_J_PIPE_2)) && (index != 0))
@@ -1038,6 +1181,8 @@ bool MSIMotherboard185Controller::ReadFwVersion()
     ret_val &= hid_write(dev, request, 64);
     ret_val &= hid_read(dev, response, 64);
 
+    version_APROM_val = response[2];
+
     /*-----------------------------------------------------*\
     | Extract high and low values from response             |
     \*-----------------------------------------------------*/
@@ -1125,16 +1270,16 @@ void MSIMotherboard185Controller::GetMode
     | Update pointers with data                             |
     \*-----------------------------------------------------*/
     mode            = (MSI_MODE)        zone_data->effect;
-    speed           = (MSI_SPEED)(zone_data->speedAndBrightnessFlags & 0x03);
-    brightness      = (MSI_BRIGHTNESS)((zone_data->speedAndBrightnessFlags >> 2) & 0x1F);
-    rainbow_color   = (zone_data->colorFlags & 0x80) == 0 ? true : false;
+    speed           = (MSI_SPEED)     ((zone_data->speedAndBrightnessFlags >> MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT)      & MSI_SPEED_BRIGHTNESS_FLAG_SPEED_MASK);
+    brightness      = (MSI_BRIGHTNESS)((zone_data->speedAndBrightnessFlags >> MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT) & MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_MASK);
+    rainbow_color   = ((zone_data->colorFlags & MSI_COLOR_FLAG_USE_CUSTOM_COLOR) == 0 ? false : true);
     color           = ToRGBColor(zone_data->color.R, zone_data->color.G, zone_data->color.B);
 }
 
-void MSIMotherboard185Controller::SetCycleCount
+void MSIMotherboard185Controller::SetZoneLEDCount
     (
     MSI_ZONE        zone,
-    unsigned char   cycle_num
+    unsigned char   led_num
     )
 {
     RainbowZoneData *requested_zone = GetRainbowZoneData(zone);
@@ -1144,7 +1289,7 @@ void MSIMotherboard185Controller::SetCycleCount
         return;
     }
 
-    requested_zone->cycle_or_led_num = cycle_num;
+    requested_zone->cycle_or_led_num = led_num;
     SelectPerLedProtocol();
 }
 
@@ -1154,6 +1299,7 @@ void MSIMotherboard185Controller::SetDirectMode
     )
 {
     direct_mode             = mode;
+    direct_mode_configured  = false;
     SelectPerLedProtocol();
 }
 
@@ -1212,9 +1358,8 @@ size_t MSIMotherboard185Controller::GetMaxDirectLeds
     }
 }
 
-void MSIMotherboard185Controller::SelectPerLedProtocol()
+bool MSIMotherboard185Controller::SelectPerLedProtocol()
 {
-
     unsigned char jrainbow1_size = 0;
     unsigned char jrainbow2_size = 0;
     unsigned char jrainbow3_size = 0;
@@ -1283,7 +1428,17 @@ void MSIMotherboard185Controller::SelectPerLedProtocol()
     {
         if(per_led_mode == DIRECT_MODE_PER_LED)
         {
-            hid_send_feature_report(dev, (unsigned char*)&enable_per_led_msg, sizeof(enable_per_led_msg));
+            if(hid_send_feature_report(dev, (unsigned char*)&enable_per_led_msg, sizeof(enable_per_led_msg)) != sizeof(enable_per_led_msg))
+            {
+                return false;
             }
+            direct_mode_configured = true;
+        }
+
+        return true;
+    }
+    else
+    {
+        return false;
     }
 }

Controllers/MSIMotherboardController/MSIMotherboard185Controller/MSIMotherboard185Controller.h

@@ -46,6 +46,7 @@ public:
                         );
 
     MSI_MODE        GetMode();
+    bool            GetFirmwareVersionInvalid();
 
     void            GetMode
                         (
@@ -77,10 +78,10 @@ public:
                         unsigned char   blu
                         );
 
-    void            SetCycleCount
+    void            SetZoneLEDCount
                         (
                         MSI_ZONE        zone,
-                        unsigned char   cycle_num
+                        unsigned char   led_num
                         );
 
     bool            Update
@@ -119,6 +120,8 @@ private:
     std::string                     name;
     std::string                     location;
     std::string                     version_APROM;
+    unsigned char                   version_APROM_val;
+    bool                            version_invalid;
     std::string                     version_LDROM;
 
     FeaturePacket_185               data;
@@ -128,6 +131,7 @@ private:
     FeaturePacket_PerLED_185        per_led_data_jcorsair;
     FeaturePacket_185               zone_based_per_led_data;
     bool                            direct_mode;
+    bool                            direct_mode_configured;
     bool                            sync_direct_mode;
     bool                            no_onboards;
     bool                            no_jrainbow1;
@@ -153,5 +157,5 @@ private:
                         (
                         MSI_ZONE zone
                         );
-    void            SelectPerLedProtocol();
+    bool            SelectPerLedProtocol();
 };

Controllers/MSIMotherboardController/MSIMotherboard185Controller/RGBController_MSIMotherboard185.cpp

@@ -227,7 +227,7 @@ void RGBController_MSIMotherboard185::SetupZones()
             last_resizable_zone                         = zd->zone_type;
         }
 
-        controller->SetCycleCount(zone_description[zone_idx]->zone_type, zones[zone_idx].leds_count);
+        controller->SetZoneLEDCount(zone_description[zone_idx]->zone_type, zones[zone_idx].leds_count);
 
         if((zones[zone_idx].flags & ZONE_FLAG_MANUALLY_CONFIGURABLE_SIZE_EFFECTS_ONLY) == 0)
         {
@@ -267,6 +267,11 @@ void RGBController_MSIMotherboard185::DeviceConfigureZone(int zone_idx)
 
 void RGBController_MSIMotherboard185::DeviceUpdateLEDs()
 {
+    if((modes[active_mode].value == MSI_MODE_DIRECT_DUMMY) && !controller->IsDirectModeActive())
+    {
+        controller->SetDirectMode(true);
+    }
+
     for(std::size_t zone_idx = 0; zone_idx < zones.size(); ++zone_idx)
     {
         for(int led_idx = zones[zone_idx].leds_count - 1; led_idx >= 0; led_idx--)
@@ -279,6 +284,11 @@ void RGBController_MSIMotherboard185::DeviceUpdateLEDs()
 
 void RGBController_MSIMotherboard185::DeviceUpdateZoneLEDs(int zone)
 {
+    if((modes[active_mode].value == MSI_MODE_DIRECT_DUMMY) && !controller->IsDirectModeActive())
+    {
+        controller->SetDirectMode(true);
+    }
+
     for(int led_idx = zones[zone].leds_count - 1; led_idx >= 0; led_idx--)
     {
         UpdateLed(zone, led_idx);
@@ -291,6 +301,11 @@ void RGBController_MSIMotherboard185::DeviceUpdateSingleLED
     int led
     )
 {
+    if((modes[active_mode].value == MSI_MODE_DIRECT_DUMMY) && !controller->IsDirectModeActive())
+    {
+        controller->SetDirectMode(true);
+    }
+
     int zone_index = IndexOfZoneForType((MSI_ZONE)leds[led].value);
 
     if(zone_index == -1)

Controllers/MSIMotherboardController/MSIMotherboard761Controller/MSIMotherboard761Controller.cpp

@@ -72,9 +72,15 @@ static const std::string board_names[] =
     "MSI MAG B850 TOMAHAWK WIFI (MS-7E53)",
     "MSI MEG Z890 UNIFY-X (MS-7E20)",
     "MSI PRO X870E-S EVO WIFI (MS-7E86)",
+    "MSI MAG X870E GAMING MAX WIFI (MS-7E86)",
     "MSI PRO Z890-P WIFI (MS-7E34)",
     "MSI B850 GAMING PLUS WIFI PZ (MS-7E75)",
     "MSI MAG X870E TOMAHAWK MAX WIFI PZ (MS-7E84)",
+    "MSI PRO B850M-A WIFI PZ (MS-7E78)",
+    "MSI B850MPOWER (MS-7E83)",
+    "MSI B840M GAMING WIFI6E (MS-7E76)",
+    "MSI PRO B850M-A WIFI (MS-7E66)",
+    "MSI PRO B850-S WIFI6E (MS-7E80)"
 };
 
 static const mystic_light_761_config board_configs[] =
@@ -104,9 +110,15 @@ static const mystic_light_761_config board_configs[] =
     { &(board_names[22]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI MAG B850 TOMAHAWK WIFI (MS-7E53)
     { &(board_names[23]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI MEG Z890 UNIFY-X (MS-7E20)
     { &(board_names[24]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI PRO X870E-S EVO WIFI (MS-7E86)
-    { &(board_names[25]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI PRO Z890-P WIFI (MS-7E34)
-    { &(board_names[26]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI B850 GAMING PLUS WIFI PZ (MS-7E75)
-    { &(board_names[27]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI MAG X870E TOMAHAWK MAX WIFI PZ (MS-7E84)
+    { &(board_names[25]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI MAG X870E GAMING MAX WIFI (MS-7E86)
+    { &(board_names[26]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI PRO Z890-P WIFI (MS-7E34)
+    { &(board_names[27]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI B850 GAMING PLUS WIFI PZ (MS-7E75)
+    { &(board_names[28]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI MAG X870E TOMAHAWK MAX WIFI PZ (MS-7E84)
+    { &(board_names[29]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI PRO B850M-A WIFI PZ (MS-7E78)
+    { &(board_names[30]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI B850MPOWER (MS-7E83)
+    { &(board_names[31]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI B840M GAMING WIFI6E (MS-7E76)
+    { &(board_names[32]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI PRO B850M-A WIFI (MS-7E66)
+    { &(board_names[33]), 0,  0,  0, 1, &zone_set1,  MSIMotherboard761Controller::DIRECT_MODE_ZONE_BASED },     // MSI PRO B850-S WIFI6E (MS-7E80)
 };
 
 enum MSI_ZONE setup_map [] =
@@ -591,10 +603,10 @@ void MSIMotherboard761Controller::GetMode
     color           = ToRGBColor(zone_data->color.R, zone_data->color.G, zone_data->color.B);
 }
 
-void MSIMotherboard761Controller::SetCycleCount
+void MSIMotherboard761Controller::SetZoneLEDCount
     (
     MSI_ZONE        /*zone*/,
-    unsigned char   /*cycle_num*/
+    unsigned char   /*led_num*/
     )
 {
     return;

Controllers/MSIMotherboardController/MSIMotherboard761Controller/MSIMotherboard761Controller.h

@@ -75,10 +75,10 @@ public:
                     unsigned char   blu
                     );
 
-    void        SetCycleCount
+    void        SetZoneLEDCount
                     (
                     MSI_ZONE        zone,
-                    unsigned char   cycle_num
+                    unsigned char   led_num
                     );
 
     bool        Update

Controllers/MSIMotherboardController/MSIMotherboard761Controller/RGBController_MSIMotherboard761.cpp

@@ -210,7 +210,7 @@ void RGBController_MSIMotherboard761::SetupZones()
             last_resizable_zone                         = zd->zone_type;
         }
 
-        controller->SetCycleCount(zone_description[zone_idx]->zone_type, zones[zone_idx].leds_count);
+        controller->SetZoneLEDCount(zone_description[zone_idx]->zone_type, zones[zone_idx].leds_count);
 
         if((zones[zone_idx].flags & ZONE_FLAG_MANUALLY_CONFIGURABLE_SIZE_EFFECTS_ONLY) == 0)
         {

Controllers/MSIMotherboardController/MSIMotherboardCommon.h

@@ -122,13 +122,22 @@ enum MSI_BRIGHTNESS
 #define NUMOF_PER_LED_MODE_LEDS                     240
 #define NUM_LEDS_761                                720
 
-#define SYNC_SETTING_ONBOARD                        0x01
-#define SYNC_SETTING_JRAINBOW1                      0x02
-#define SYNC_SETTING_JRAINBOW2                      0x04
-#define SYNC_SETTING_JCORSAIR                       0x08
-#define SYNC_SETTING_JPIPE1                         0x10
-#define SYNC_SETTING_JPIPE2                         0x20
-#define SYNC_SETTING_JRGB                           0x80
+/*---------------------------------------------------------*\
+| Flag bitfield bit definitions                             |
+| Note that the sync flags split across the two fields      |
+\*---------------------------------------------------------*/
+#define MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT       0
+#define MSI_SPEED_BRIGHTNESS_FLAG_SPEED_MASK        (0x03 << MSI_SPEED_BRIGHTNESS_FLAG_SPEED_SHIFT)
+#define MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT  2
+#define MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_MASK   (0x1F << MSI_SPEED_BRIGHTNESS_FLAG_BRIGHTNESS_SHIFT)
+#define MSI_SPEED_BRIGHTNESS_FLAG_SYNC_SETTING_JRGB (1 << 7)
+#define MSI_COLOR_FLAG_SYNC_SETTING_ONBOARD         (1 << 0)
+#define MSI_COLOR_FLAG_SYNC_SETTING_JRAINBOW1       (1 << 1)
+#define MSI_COLOR_FLAG_SYNC_SETTING_JRAINBOW2       (1 << 2)
+#define MSI_COLOR_FLAG_SYNC_SETTING_JCORSAIR        (1 << 3)
+#define MSI_COLOR_FLAG_SYNC_SETTING_JPIPE1          (1 << 4)
+#define MSI_COLOR_FLAG_SYNC_SETTING_JPIPE2          (1 << 5)
+#define MSI_COLOR_FLAG_USE_CUSTOM_COLOR             (1 << 7)
 
 struct Color
 {

Controllers/MSIMotherboardController/MSIMotherboardControllerDetect.cpp

@@ -54,10 +54,18 @@ DetectedControllers DetectMSIMotherboardControllers(hid_device_info* info, const
         if((packet_length >= sizeof(FeaturePacket_185)) && (packet_length <= (sizeof(FeaturePacket_185) + 1)))  //WHY r we doing this ? why not ==
         {
             MSIMotherboard185Controller*     controller     = new MSIMotherboard185Controller(dev, info->path, info->product_id, dmi_name);
+
+            if(controller->GetFirmwareVersionInvalid())
+            {
+                LOG_WARNING("[MSIMotherboard185] Controller firmware below minimum supported version, skipping");
+            }
+            else
+            {
                 RGBController_MSIMotherboard185* rgb_controller = new RGBController_MSIMotherboard185(controller);
 
                 detected_controllers.push_back(rgb_controller);
             }
+        }
         else if((packet_length >= sizeof(FeaturePacket_162)) && (packet_length <= (sizeof(FeaturePacket_162) + 1)))
         {
             MSIMotherboard162Controller*     controller     = new MSIMotherboard162Controller(dev, info->path, info->product_id, dmi_name);
@@ -223,9 +231,12 @@ REGISTER_HID_DETECTOR_PU("MSI Mystic Light MS_7E70",    DetectMSIMotherboardCont
 REGISTER_HID_DETECTOR_PU("MSI Mystic Light MS_7E59",    DetectMSIMotherboardControllers,   MSI_USB_VID,    0x7E59,   0x0001, 0x00);
 REGISTER_HID_DETECTOR_PU("MSI Mystic Light MS_7E80",    DetectMSIMotherboardControllers,   MSI_USB_VID,    0x7E80,   0x0001, 0x00);
 REGISTER_HID_DETECTOR_PU("MSI Mystic Light MS_7E81",    DetectMSIMotherboardControllers,   MSI_USB_VID,    0x7E81,   0x0001, 0x00);
+REGISTER_HID_DETECTOR_PU("MSI Mystic Light MS_7E86",    DetectMSIMotherboardControllers,   MSI_USB_VID,    0x7E86,   0x0001, 0x00);
 REGISTER_HID_DETECTOR_PU("MSI Mystic Light MS_7E34",    DetectMSIMotherboardControllers,   MSI_USB_VID,    0x7E34,   0x0001, 0x00);
 REGISTER_HID_DETECTOR_PU("MSI Mystic Light MS_7E32",    DetectMSIMotherboardControllers,   MSI_USB_VID,    0x7E32,   0x0001, 0x00);
 REGISTER_HID_DETECTOR_PU("MSI Mystic Light MS_7E20",    DetectMSIMotherboardControllers,   MSI_USB_VID,    0x7E20,   0x0001, 0x00);
+REGISTER_HID_DETECTOR_PU("MSI Mystic Light MS_7E76",    DetectMSIMotherboardControllers,   MSI_USB_VID,    0x7E76,   0x0001, 0x00);
+REGISTER_HID_DETECTOR_PU("MSI Mystic Light MS_7E66",    DetectMSIMotherboardControllers,   MSI_USB_VID,    0x7E66,   0x0001, 0x00);
 // Detector for the set of common boards
 REGISTER_HID_DETECTOR_PU("MSI Mystic Light Common",     DetectMSIMotherboardControllers,   MSI_USB_VID_COMMON,  MSI_USB_PID_COMMON, 0x0001, 0x00);
 REGISTER_HID_DETECTOR_PU("MSI Mystic Light X870",       DetectMSIMotherboardControllers,   MSI_USB_VID_COMMON,  MSI_USB_PID_COMMON, 0xFF00, 0x01);
@@ -236,6 +247,7 @@ REGISTER_CUSTOM_UDEV_RULE(msi_7e24, "MSI Mystic Light MS_7E24", "SUBSYSTEMS==\"u
 REGISTER_CUSTOM_UDEV_RULE(msi_7e26, "MSI Mystic Light MS_7E26", "SUBSYSTEMS==\"usb|hidraw\", ATTRS{idVendor}==\"1462\", ATTRS{idProduct}==\"7e26\", TAG+=\"uaccess\", TAG+=\"MSI_Mystic_Light_MS_7E26\"");
 REGISTER_CUSTOM_UDEV_RULE(msi_7e27, "MSI Mystic Light MS_7E27", "SUBSYSTEMS==\"usb|hidraw\", ATTRS{idVendor}==\"1462\", ATTRS{idProduct}==\"7e27\", TAG+=\"uaccess\", TAG+=\"MSI_Mystic_Light_MS_7E27\"");
 REGISTER_CUSTOM_UDEV_RULE(msi_7e49, "MSI Mystic Light MS_7E49", "SUBSYSTEMS==\"usb|hidraw\", ATTRS{idVendor}==\"1462\", ATTRS{idProduct}==\"7e49\", TAG+=\"uaccess\", TAG+=\"MSI_Mystic_Light_MS_7E49\"");
+REGISTER_CUSTOM_UDEV_RULE(msi_7e76, "MSI Mystic Light MS_7E76", "SUBSYSTEMS==\"usb|hidraw\", ATTRS{idVendor}==\"1462\", ATTRS{idProduct}==\"7e76\", TAG+=\"uaccess\", TAG+=\"MSI_Mystic_Light_MS_7E76\"");
 
 #ifdef ENABLE_UNTESTED_MYSTIC_LIGHT
 REGISTER_HID_DETECTOR_PU("MSI Mystic Light MS_3EA4",    DetectMSIMotherboardControllers,   MSI_USB_VID,    0x3EA4,   0x0001, 0x00);

Controllers/NVIDIAIlluminationController/NVIDIAIlluminationControllerDetect_Windows_Linux.cpp

@@ -56,6 +56,7 @@ static const nv_gpu_pci_device device_list[] =
     {NVIDIA_VEN,    NVIDIA_RTX3060_8G_DEV,          NVIDIA_SUB_VEN,   NVIDIA_RTX3060_8G_DEV,                          NVIDIA_ILLUMINATION_V1,     TREATS_RGBW_AS_RGB,     "Gainward GeForce RTX 3060 Pegasus"           },
     {NVIDIA_VEN,    NVIDIA_RTX3060_LHR_DEV,         NVIDIA_SUB_VEN,   NVIDIA_RTX3060_LHR_DEV,                         NVIDIA_ILLUMINATION_V1,     TREATS_RGBW_AS_RGB,     "Palit GeForce RTX 3060 LHR"                  },
     {NVIDIA_VEN,    NVIDIA_RTX3060_LHR_DEV,         PNY_SUB_VEN,      PNY_RTX_3060_XLR8_REVEL_EPIC_X_SUB_DEV,         NVIDIA_ILLUMINATION_V1,     TREATS_RGBW_AS_RGB,     "PNY GeForce RTX 3060 XLR8 REVEL EPIC-X"      },
+    {NVIDIA_VEN,    NVIDIA_RTX3060_LHR_DEV,         PNY_SUB_VEN,      PNY_RTX_3060_XLR8_REVEL_EPIC_X_LHR_SUB_DEV,     NVIDIA_ILLUMINATION_V1,     TREATS_RGBW_AS_RGB,     "PNY GeForce RTX 3060 XLR8 REVEL EPIC-X LHR"  },
     {NVIDIA_VEN,    NVIDIA_RTX3060_GA104_DEV,       PNY_SUB_VEN,      PNY_RTX_3060_XLR8_REVEL_EPIC_X_SUB_DEV,         NVIDIA_ILLUMINATION_V1,     TREATS_RGBW_AS_RGB,     "PNY GeForce RTX 3060 XLR8 REVEL EPIC-X"      },
     {NVIDIA_VEN,    NVIDIA_RTX3060_GA104_DEV,       NVIDIA_SUB_VEN,   NVIDIA_RTX3060_GA104_DEV,                       NVIDIA_ILLUMINATION_V1,     TREATS_RGBW_AS_RGB,     "Palit GeForce RTX 3060 LHR"                  },
     {NVIDIA_VEN,    NVIDIA_RTX3060TI_LHR_DEV,       PNY_SUB_VEN,      PNY_RTX_3060TI_XLR8_REVEL_EPIC_X_SUB_DEV,       NVIDIA_ILLUMINATION_V1,     TREATS_RGBW_AS_RGB,     "PNY GeForce RTX 3060 Ti XLR8 REVEL EPIC-X"   },

Controllers/NVIDIAIlluminationController/RGBController_NVIDIAIllumination_Windows_Linux.cpp

@@ -68,8 +68,6 @@ RGBController_NVIDIAIlluminationV1::RGBController_NVIDIAIlluminationV1(NVIDIAIll
     Static.value            = NVIDIA_ILLUMINATION_DIRECT;
     Static.flags            = MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_PER_LED_COLOR;
     Static.color_mode       = MODE_COLORS_PER_LED;
-    Static.colors_min       = 1;
-    Static.colors_max       = 1;
     Static.brightness_min   = 0;
     Static.brightness       = 100;
     Static.brightness_max   = 100;

Controllers/NZXTHue2Controller/NZXTHue2Controller.h

@@ -55,15 +55,12 @@ enum
 
 /*---------------------------------------------------------*\
 | Bounds for the device-list read-until-response loop.      |
-| Neither value comes from a measurement against real       |
-| hardware - it's a reasonable default at the same scale    |
-| hid_read_timeout() is used elsewhere in this codebase     |
-| (10-100ms per read). 1s total worst-case is enough to     |
-| absorb a slow reply without hanging forever if the        |
-| device never answers correctly at all.                    |
+| Tested against Smart Device V2, required between 100-200  |
+| ms to detect attached devices, so 1000ms was chosen to    |
+| provide an ample buffer on top of that.                   |
 \*---------------------------------------------------------*/
-#define NZXT_HUE_2_DEVICE_LIST_READ_TIMEOUT_MS  50
-#define NZXT_HUE_2_DEVICE_LIST_MAX_RETRIES      20
+#define NZXT_HUE_2_DEVICE_LIST_READ_TIMEOUT_MS  1000
+#define NZXT_HUE_2_DEVICE_LIST_MAX_RETRIES      10
 
 enum
 {

Controllers/PNYARGBEpicXGPUController/PNYARGBEpicXGPUControllerDetect.cpp

@@ -51,5 +51,6 @@ REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 5060Ti ARGB Epic-X OC", DetectPNYARGB
 REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 5070 ARGB Epic-X OC",   DetectPNYARGBEpicXGPUSmallControllers, NVIDIA_VEN, NVIDIA_RTX5070_DEV,   PNY_SUB_VEN, PNY_RTX_5070_ARGB_EPIC_X_OC_SUB_DEV,       0x60);
 REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 5070Ti ARGB Epic-X",    DetectPNYARGBEpicXGPUSmallControllers, NVIDIA_VEN, NVIDIA_RTX5070TI_DEV, PNY_SUB_VEN, PNY_RTX_5070TI_ARGB_EPIC_X_SUB_DEV,        0x60);
 REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 5070Ti ARGB Epic-X OC", DetectPNYARGBEpicXGPUSmallControllers, NVIDIA_VEN, NVIDIA_RTX5070TI_DEV, PNY_SUB_VEN, PNY_RTX_5070TI_ARGB_EPIC_X_OC_SUB_DEV,     0x60);
+REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 5070Ti ARGB Epic-X OC", DetectPNYARGBEpicXGPUSmallControllers, NVIDIA_VEN, NVIDIA_RTX5070TI_DEV, PNY_SUB_VEN, PNY_RTX_5070TI_ARGB_EPIC_X_OC_SUB_DEV2,    0x60);
 REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 5080 ARGB Epic-X OC",   DetectPNYARGBEpicXGPULargeControllers, NVIDIA_VEN, NVIDIA_RTX5080_DEV,   PNY_SUB_VEN, PNY_RTX_5080_ARGB_EPIC_X_OC_SUB_DEV,       0x60);
 REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 5090 ARGB Epic-X OC",   DetectPNYARGBEpicXGPULargeControllers, NVIDIA_VEN, NVIDIA_RTX5090_DEV,   PNY_SUB_VEN, PNY_RTX_5090_ARGB_EPIC_X_OC_SUB_DEV,       0x60);

Controllers/PNYGPUController/PNYGPUController.cpp

@@ -1,112 +0,0 @@
-/*---------------------------------------------------------*\
-| PNYGPUController.cpp                                      |
-|                                                           |
-|   Driver for PNY Turing GPU                               |
-|                                                           |
-|   KendallMorgan                               17 Oct 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include "PNYGPUController.h"
-
-PNYGPUController::PNYGPUController(i2c_smbus_interface* bus, pny_dev_id dev, std::string name)
-{
-    this->bus   = bus;
-    this->dev   = dev;
-    this->name  = name;
-}
-
-PNYGPUController::~PNYGPUController()
-{
-
-}
-
-std::string PNYGPUController::GetDeviceName()
-{
-    return(name);
-}
-
-std::string PNYGPUController::GetDeviceLocation()
-{
-    std::string return_string(bus->info.device_name);
-    char addr[5];
-    snprintf(addr, 5, "0x%02X", dev);
-    return_string.append(", address ");
-    return_string.append(addr);
-    return("I2C: " + return_string);
-}
-
-void PNYGPUController::WriteI2CData(u8 command, u8 length, u8* data)
-{
-    //Simulating i2c_smbus_write_i2c_block_data(command, length, data);
-    for (u8 i = 0; i < length; i++)
-    {
-        bus->i2c_smbus_write_byte_data(dev, command+i, data[i]);
-    }
-}
-
-unsigned char PNYGPUController::GetMode()
-{
-    return(bus->i2c_smbus_read_byte_data(dev, PNY_GPU_MODE_OFF));
-}
-
-unsigned char PNYGPUController::GetRed()
-{
-    return(bus->i2c_smbus_read_byte_data(dev, PNY_GPU_REG_COLOR_RED));
-}
-
-unsigned char PNYGPUController::GetGreen()
-{
-    return(bus->i2c_smbus_read_byte_data(dev, PNY_GPU_REG_COLOR_GREEN));
-}
-
-unsigned char PNYGPUController::GetBlue()
-{
-    return(bus->i2c_smbus_read_byte_data(dev, PNY_GPU_REG_COLOR_BLUE));
-}
-
-void PNYGPUController::SetOff()
-{
-    bus->i2c_smbus_write_byte_data(dev, PNY_GPU_REG_CONTROL,                0);
-    bus->i2c_smbus_write_byte_data(dev, PNY_GPU_REG_MODE,                   0x00);
-}
-
-void PNYGPUController::SetCycle(unsigned char speed)
-{
-    u8 loop[] = {
-        0x01,  // Direction
-        0x00,  // ??
-        speed, // Speed
-        0x1F   // Somehow related to speed
-    };
-    loop[2] = speed;
-    WriteI2CData(PNY_GPU_REG_CONTROL, sizeof(loop), loop);
-}
-
-void PNYGPUController::SetStrobe(unsigned char r, unsigned char g, unsigned char b, unsigned char speed, unsigned char brightness)
-{
-    u8 strobe[] = {
-        0x02,       // Strobe
-        0x00,       // Rise speed
-        speed,      // Cycle length/2
-        0x00,       // Off delay
-        r,          // R
-        g,          // G
-        b,          // B
-        brightness, // Peak brightness
-        0x05        // Fade speed
-    };
-    WriteI2CData(PNY_GPU_REG_CONTROL, sizeof(strobe), strobe);
-}
-
-void PNYGPUController::SetDirect(unsigned char red, unsigned char green, unsigned char blue, unsigned char brightness)
-{
-    bus->i2c_smbus_write_byte_data(dev, PNY_GPU_REG_CONTROL,                0);
-    bus->i2c_smbus_write_byte_data(dev, PNY_GPU_REG_MODE,                   0x01);
-    bus->i2c_smbus_write_byte_data(dev, PNY_GPU_REG_COLOR_RED,              red);
-    bus->i2c_smbus_write_byte_data(dev, PNY_GPU_REG_COLOR_BLUE,             blue);
-    bus->i2c_smbus_write_byte_data(dev, PNY_GPU_REG_COLOR_GREEN,            green);
-    bus->i2c_smbus_write_byte_data(dev, PNY_GPU_REG_COLOR_BRIGHTNESS,       brightness);
-}

Controllers/PNYGPUController/PNYGPUController.h

@@ -1,62 +0,0 @@
-/*---------------------------------------------------------*\
-| PNYGPUController.h                                        |
-|                                                           |
-|   Driver for PNY Turing GPU                               |
-|                                                           |
-|   KendallMorgan                               17 Oct 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#pragma once
-
-#include <string>
-#include "i2c_smbus.h"
-
-typedef unsigned char   pny_dev_id;
-
-enum
-{
-    PNY_GPU_REG_CONTROL                 = 0xE0,
-    PNY_GPU_REG_MODE                    = 0x60,
-    PNY_GPU_REG_COLOR_RED               = 0x6C,
-    PNY_GPU_REG_COLOR_GREEN             = 0x6D,
-    PNY_GPU_REG_COLOR_BLUE              = 0x6E,
-    PNY_GPU_REG_COLOR_BRIGHTNESS        = 0x6F,
-};
-
-enum
-{
-    PNY_GPU_MODE_OFF                    = 0x00,
-    PNY_GPU_MODE_DIRECT                 = 0x01,
-    PNY_GPU_MODE_CYCLE                  = 0x02,
-    PNY_GPU_MODE_STROBE                 = 0x03,
-};
-
-class PNYGPUController
-{
-public:
-	PNYGPUController(i2c_smbus_interface* bus, pny_dev_id dev, std::string name);
-	~PNYGPUController();
-
-    std::string     GetDeviceName();
-	std::string     GetDeviceLocation();
-
-    void SetOff();
-    void SetCycle(unsigned char speed);
-    void SetStrobe(unsigned char r, unsigned char g, unsigned char b, unsigned char speed, unsigned char brightness);
-    void SetDirect(unsigned char red, unsigned char green, unsigned char blue, unsigned char brightness);
-
-private:
-	i2c_smbus_interface*    bus;
-	pny_dev_id              dev;
-    std::string             name;
-
-    void            WriteI2CData(u8 command, u8 length, u8* data);
-    unsigned char   GetMode();
-    unsigned char   GetRed();
-    unsigned char   GetGreen();
-    unsigned char   GetBlue();
-
-};

Controllers/PNYGPUController/PNYGPUControllerDetect.cpp

@@ -1,76 +0,0 @@
-/*---------------------------------------------------------*\
-| PNYGPUControllerDetect.cpp                                |
-|                                                           |
-|   Detector for PNY Turing GPU                             |
-|                                                           |
-|   KendallMorgan                               17 Oct 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include "DetectionManager.h"
-#include "i2c_smbus.h"
-#include "pci_ids.h"
-#include "PNYGPUController.h"
-#include "RGBController_PNYGPU.h"
-
-DetectedControllers DetectPNYGPUControllers(i2c_smbus_interface* bus, uint8_t i2c_addr, const std::string& name)
-{
-    DetectedControllers detected_controllers;
-
-    if(bus->info.port_id == 1)
-    {
-        PNYGPUController*     controller        = new PNYGPUController(bus, i2c_addr, name);
-        RGBController_PNYGPU* rgb_controller    = new RGBController_PNYGPU(controller);
-
-        detected_controllers.push_back(rgb_controller);
-    }
-
-    return(detected_controllers);
-}
-
-REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 2060 XLR8 OC EDITION",       DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX2060_TU104_DEV,   PNY_SUB_VEN,    PNY_RTX_2060_XLR8_OC_SUB_DEV,               0x49);
-REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3060 XLR8 Revel EPIC-X",     DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3060_DEV,         PNY_SUB_VEN,    PNY_RTX_3060_XLR8_REVEL_EPIC_X_SUB_DEV,     0x49);
-REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3070 XLR8 Revel EPIC-X",     DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3070_DEV,         PNY_SUB_VEN,    PNY_RTX_3070_XLR8_REVEL_EPIC_X_SUB_DEV,     0x49);
-REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3070 XLR8 Revel EPIC-X LHR", DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3070_LHR_DEV,     PNY_SUB_VEN,    PNY_RTX_3070_XLR8_REVEL_EPIC_X_LHR_SUB_DEV, 0x49);
-REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3080 XLR8 Revel EPIC-X",     DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3080_DEV,         PNY_SUB_VEN,    PNY_RTX_3080_XLR8_REVEL_EPIC_X_SUB_DEV,     0x49);
-REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3080 Ti XLR8 Revel EPIC-X",  DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3080TI_DEV,       PNY_SUB_VEN,    PNY_RTX_3080TI_XLR8_REVEL_EPIC_X_SUB_DEV,   0x49);
-REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3090 XLR8 Revel EPIC-X",     DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3090_DEV,         PNY_SUB_VEN,    PNY_RTX_3090_XLR8_REVEL_EPIC_X_SUB_DEV,     0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 2070 SUPER Jetstream",     DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX2070S_OC_DEV,     NVIDIA_SUB_VEN, NVIDIA_RTX2070S_OC_DEV,                     0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3060",                     DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3060_DEV,         PALIT_SUB_VEN,  PALIT_RTX3060_SUB_DEV,                      0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3060 LHR",                 DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3060_LHR_DEV,     PALIT_SUB_VEN,  PALIT_RTX3060_LHR_SUB_DEV,                  0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3060 Ti",                  DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3060TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX3060TI_SUB_DEV,                    0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3060 Ti LHR",              DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3060TI_LHR_DEV,   PALIT_SUB_VEN,  NVIDIA_RTX3060TI_LHR_DEV,                   0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3060 Ti Dual",             DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3060TI_DEV,       NVIDIA_SUB_VEN, PALIT_RTX3060TI_SUB_DEV,                    0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3070",                     DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3070_DEV,         PALIT_SUB_VEN,  PALIT_RTX3070_SUB_DEV,                      0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3070 LHR",                 DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3070_LHR_DEV,     PALIT_SUB_VEN,  PALIT_RTX3070_LHR_SUB_DEV,                  0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3070 Gamerock LHR",        DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3070_LHR_DEV,     PALIT_SUB_VEN,  PALIT_RTX3070_GAMEROCK_SUB_DEV,             0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3070 Ti",                  DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3070TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX3070TI_SUB_DEV,                    0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3070 Ti GamingPro",        DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3070TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX3070TI_GAMING_PRO_SUB_DEV,         0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3080",                     DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3080_DEV,         PALIT_SUB_VEN,  PALIT_RTX3080_SUB_DEV,                      0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3080 LHR",                 DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3080_LHR_DEV,     PALIT_SUB_VEN,  PALIT_RTX3080_LHR_SUB_DEV,                  0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3080 Gamerock",            DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3080_DEV,         PALIT_SUB_VEN,  PALIT_RTX3080_GAMEROCK_SUB_DEV,             0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3080 Gamerock LHR",        DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3080_LHR_DEV,     PALIT_SUB_VEN,  PALIT_RTX3080_GAMEROCK_SUB_DEV,             0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3080 12GB GamingPro",      DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3080_12G_LHR_DEV, PALIT_SUB_VEN,  PALIT_RTX3080_GAMINGPRO_12G_SUB_DEV,        0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3080 Ti",                  DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3080TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX3080TI_SUB_DEV,                    0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3080 Ti Gamerock",         DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3080TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX3080TI_GAMEROCK_SUB_DEV,           0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3090",                     DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3090_DEV,         PALIT_SUB_VEN,  PALIT_RTX3090_SUB_DEV,                      0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3090 Gamerock",            DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3090_DEV,         PALIT_SUB_VEN,  PALIT_RTX3090_GAMEROCK_SUB_DEV,             0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3090 Ti Gamerock",         DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX3090TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX3090TI_GAMEROCK_SUB_DEV,           0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4070 Ti",                  DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX4070TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX4070TI_SUB_DEV,                    0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4070 Ti Gamerock",         DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX4070TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX4070TI_GAMEROCK_SUB_DEV,           0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4070 Ti SUPER GamingPro",  DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX4070TIS_DEV,      PALIT_SUB_VEN,  PALIT_RTX4080_GAMINGPRO_SUB_DEV,            0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4080 GamingPro",           DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX4080_DEV,         PALIT_SUB_VEN,  PALIT_RTX4080_GAMINGPRO_SUB_DEV,            0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4080 SUPER GamingPro",     DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX4080S_DEV,        PALIT_SUB_VEN,  PALIT_RTX4080_GAMINGPRO_SUB_DEV,            0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4090 Gamerock",            DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX4090_DEV,         PALIT_SUB_VEN,  PALIT_RTX4090_GAMEROCK_SUB_DEV,             0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5060 Ti White OC 16GB",    DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX5060TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX5060TI_WHITE_OC_16G_SUB_DEV,       0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5070 GamingPro",           DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX5070_DEV,         PALIT_SUB_VEN,  PALIT_RTX5070_GAMINGPRO_SUB_DEV,            0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5070 Ti GameRock",         DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX5070TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX5070TI_GAMEROCK_SUB_DEV,           0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5070 Ti GamingPro",        DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX5070TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX5070TI_GAMINGPRO_SUB_DEV,          0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5070 Ti GamingPro-S",      DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX5070TI_DEV,       PALIT_SUB_VEN,  PALIT_RTX5070TI_GAMINGPRO_S_SUB_DEV,        0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5080 GameRock",            DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX5080_DEV,         PALIT_SUB_VEN,  PALIT_RTX5080_GAMEROCK_SUB_DEV,             0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5080 GamingPro",           DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX5080_DEV,         PALIT_SUB_VEN,  PALIT_RTX5080_GAMINGPRO_SUB_DEV,            0x49);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5090 Gamerock",            DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX5090_DEV,         PALIT_SUB_VEN,  PALIT_RTX5090_GAMEROCK_SUB_DEV,             0x49);
-REGISTER_I2C_PCI_DETECTOR("NVIDIA GeForce RTX 2060 SUPER",              DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX2060_TU106_DEV,   NVIDIA_SUB_VEN, NVIDIA_RTX2060_TU106_DEV,                   0x49);
-REGISTER_I2C_PCI_DETECTOR("NVIDIA GeForce RTX 2080 SUPER",              DetectPNYGPUControllers,    NVIDIA_VEN, NVIDIA_RTX2080S_DEV,        NVIDIA_SUB_VEN, NVIDIA_RTX2080S_DEV,                        0x49);

Controllers/PNYGPUController/RGBController_PNYGPU.cpp

@@ -1,161 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_PNYGPU.cpp                                  |
-|                                                           |
-|   RGBController for PNY Turing GPU                        |
-|                                                           |
-|   KendallMorgan                               17 Oct 2021 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include "RGBController_PNYGPU.h"
-
-/**------------------------------------------------------------------*\
-    @name PNY GPU
-    @category GPU
-    @type I2C
-    @save :x:
-    @direct :white_check_mark:
-    @effects :white_check_mark:
-    @detectors DetectPNYGPUControllers
-    @comment
-\*-------------------------------------------------------------------*/
-
-RGBController_PNYGPU::RGBController_PNYGPU(PNYGPUController* controller_ptr)
-{
-    controller              = controller_ptr;
-
-    name                    = controller->GetDeviceName();
-    vendor                  = name.substr(0, name.find(' '));
-    description             = "PNY/Palit RGB GPU Device";
-    location                = controller->GetDeviceLocation();
-
-    type                    = DEVICE_TYPE_GPU;
-
-    mode Off;
-    Off.name                = "Off";
-    Off.value               = PNY_GPU_MODE_OFF;
-    Off.flags               = 0;
-    Off.color_mode          = MODE_COLORS_NONE;
-    modes.push_back(Off);
-
-    mode Direct;
-    Direct.name             = "Direct";
-    Direct.value            = PNY_GPU_MODE_DIRECT;
-    Direct.flags            = MODE_FLAG_HAS_PER_LED_COLOR| MODE_FLAG_HAS_BRIGHTNESS;
-    Direct.brightness       = 255;
-    Direct.brightness_min   = 0;
-    Direct.brightness_max   = 100;
-    Direct.color_mode       = MODE_COLORS_PER_LED;
-    modes.push_back(Direct);
-
-    mode Cycle;
-    Cycle.name             = "Cycle";
-    Cycle.value            = PNY_GPU_MODE_CYCLE;
-    Cycle.flags            = MODE_FLAG_HAS_SPEED;
-    Cycle.speed            = 3;
-    Cycle.speed_max        = 0;
-    Cycle.speed_max        = 100;
-    Cycle.color_mode       = MODE_COLORS_PER_LED;
-    modes.push_back(Cycle);
-
-    mode Strobe;
-    Strobe.name             = "Strobe";
-    Strobe.value            = PNY_GPU_MODE_STROBE;
-    Strobe.flags            = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_SPEED | MODE_FLAG_HAS_BRIGHTNESS;
-    Strobe.speed            = 2;
-    Strobe.speed_max        = 0;
-    Strobe.speed_max        = 255;
-    Strobe.brightness       = 255;
-    Strobe.brightness_min   = 0;
-    Strobe.brightness_max   = 100;
-    Strobe.color_mode       = MODE_COLORS_PER_LED;
-    modes.push_back(Strobe);
-
-
-    SetupZones();
-
-    // Initialize active mode
-    active_mode = 0;
-}
-
-RGBController_PNYGPU::~RGBController_PNYGPU()
-{
-    Shutdown();
-
-    delete controller;
-}
-
-void RGBController_PNYGPU::SetupZones()
-{
-    /*---------------------------------------------------------*\
-    | This device only has one LED, so create a single zone and |
-    | LED for it                                                |
-    \*---------------------------------------------------------*/
-    zone* new_zone = new zone();
-    led*  new_led  = new led();
-
-    new_zone->name          = "GPU Zone";
-    new_zone->type          = ZONE_TYPE_SINGLE;
-    new_zone->leds_min      = 1;
-    new_zone->leds_max      = 1;
-    new_zone->leds_count    = 1;
-
-    new_led->name           = "GPU LED";
-
-    /*---------------------------------------------------------*\
-    | Push the zone and LED on to device vectors                |
-    \*---------------------------------------------------------*/
-    leds.push_back(*new_led);
-    zones.push_back(*new_zone);
-    SetupColors();
-}
-
-void RGBController_PNYGPU::DeviceUpdateLEDs()
-{
-    DeviceUpdateMode();
-}
-
-void RGBController_PNYGPU::DeviceUpdateZoneLEDs(int /*zone*/)
-{
-    DeviceUpdateLEDs();
-}
-
-void RGBController_PNYGPU::DeviceUpdateSingleLED(int /*led*/)
-{
-    DeviceUpdateLEDs();
-}
-
-void RGBController_PNYGPU::DeviceUpdateMode()
-{
-    RGBColor      color = colors[0];
-    unsigned char r   = RGBGetRValue(color);
-    unsigned char g   = RGBGetGValue(color);
-    unsigned char b   = RGBGetBValue(color);
-    unsigned char speed, brightness;
-    switch(modes[active_mode].value)
-    {
-        case PNY_GPU_MODE_OFF:
-            controller->SetOff();
-            break;
-
-        case PNY_GPU_MODE_DIRECT:
-            brightness = modes[active_mode].brightness;
-            controller->SetDirect(r, g, b, brightness);
-            break;
-
-        case PNY_GPU_MODE_CYCLE:
-            speed = modes[active_mode].speed;
-            controller->SetCycle(speed);
-            break;
-
-        case PNY_GPU_MODE_STROBE:
-            speed      = modes[active_mode].speed;
-            brightness = modes[active_mode].brightness;
-            controller->SetStrobe(r, g, b, speed, brightness);
-            break;
-        default:
-        break;
-    }
-}

Controllers/PalitGPUController/PalitGPUController.cpp

@@ -1,46 +0,0 @@
-/*---------------------------------------------------------*\
-| PalitGPUController.cpp                                    |
-|                                                           |
-|   Driver for Palit GPU                                    |
-|                                                           |
-|   Manatsawin Hanmongkolchai                   11 Apr 2023 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include "PalitGPUController.h"
-
-PalitGPUController::PalitGPUController(i2c_smbus_interface* bus, palit_dev_id dev, std::string dev_name)
-{
-    this->bus   = bus;
-    this->dev   = dev;
-    this->name  = dev_name;
-}
-
-PalitGPUController::~PalitGPUController()
-{
-
-}
-
-std::string PalitGPUController::GetDeviceLocation()
-{
-    std::string return_string(bus->info.device_name);
-    char addr[5];
-    snprintf(addr, 5, "0x%02X", dev);
-    return_string.append(", address ");
-    return_string.append(addr);
-    return("I2C: " + return_string);
-}
-
-std::string PalitGPUController::GetName()
-{
-    return(name);
-}
-
-void PalitGPUController::SetDirect(unsigned char red, unsigned char green, unsigned char blue)
-{
-    // NvAPI_I2CWriteEx:  Dev: 0x08 RegSize: 0x01 Reg: 0x03 Size: 0x04 Data: 0xFF 0x00 0x00 0xFF
-    uint8_t values[] = {red, green, blue, 0xFF};
-    bus->i2c_smbus_write_i2c_block_data(dev, PALIT_GPU_REG_LED, sizeof(values), values);
-}

Controllers/PalitGPUController/PalitGPUController.h

@@ -1,44 +0,0 @@
-/*---------------------------------------------------------*\
-| PalitGPUController.h                                      |
-|                                                           |
-|   Driver for Palit GPU                                    |
-|                                                           |
-|   Manatsawin Hanmongkolchai                   11 Apr 2023 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#pragma once
-
-#include <string>
-#include "i2c_smbus.h"
-
-typedef unsigned char       palit_dev_id;
-
-enum
-{
-    PALIT_GPU_MODE_DIRECT   = 0x00,
-};
-
-enum
-{
-    PALIT_GPU_REG_LED       = 0x03,
-};
-
-class PalitGPUController
-{
-public:
-	PalitGPUController(i2c_smbus_interface* bus, palit_dev_id dev, std::string dev_name);
-	~PalitGPUController();
-
-	std::string             GetDeviceLocation();
-    std::string             GetName();
-
-    void                    SetDirect(unsigned char red, unsigned char green, unsigned char blue);
-
-private:
-	i2c_smbus_interface*    bus;
-	palit_dev_id            dev;
-    std::string             name;
-};

Controllers/PalitGPUController/PalitGPUControllerDetect.cpp

@@ -4,6 +4,9 @@
 |   Detector for Palit GPU                                  |
 |                                                           |
 |   Manatsawin Hanmongkolchai                   11 Apr 2023 |
+|   TheRogueZeta                                05 Nov 2020 |
+|   KundaPanda                                  04 Jan 2021 |
+|   KendallMorgan                               17 Oct 2021 |
 |                                                           |
 |   This file is part of the OpenRGB project                |
 |   SPDX-License-Identifier: GPL-2.0-or-later               |
@@ -13,19 +16,22 @@
 #include <stdlib.h>
 #include "DetectionManager.h"
 #include "i2c_smbus.h"
-#include "PalitGPUController.h"
+#include "PalitGPUv1Controller.h"
+#include "PalitGPUv2Controller.h"
 #include "pci_ids.h"
-#include "RGBController_PalitGPU.h"
+#include "RGBController_PalitGPUv1.h"
+#include "RGBController_PalitGPUv2.h"
 
-DetectedControllers DetectPalitGPUControllers(i2c_smbus_interface* bus, uint8_t i2c_addr, const std::string& name)
+bool TestForPalitGPUv1Controller(i2c_smbus_interface* bus, uint8_t i2c_addr)
 {
-    DetectedControllers detected_controllers;
+    bool pass = false;
 
     if(bus->info.port_id == 1)
     {
-        /*-----------------------------------------------------*\
-        | Check for PALIT string                                |
-        \*-----------------------------------------------------*/
+        /*-------------------------------------------------*\
+        | Check for PALIT string, which is known to work    |
+        | for Palit variants                                |
+        \*-------------------------------------------------*/
         const uint8_t   palit[] = {'P', 'A', 'L', 'I', 'T'};
         bool            match   = true;
 
@@ -39,20 +45,151 @@ DetectedControllers DetectPalitGPUControllers(i2c_smbus_interface* bus, uint8_t
             }
         }
 
+        /*-------------------------------------------------*\
+        | If PALIT string fails, try a quick write to the   |
+        | target address, which is known to work for        |
+        | Gainward variants                                 |
+        \*-------------------------------------------------*/
         if(match)
         {
-            PalitGPUController*     controller      = new PalitGPUController(bus, i2c_addr, name);
-            RGBController_PalitGPU* rgb_controller  = new RGBController_PalitGPU(controller);
-
-            DetectionManager::get()->RegisterRGBController(rgb_controller);
+            pass = true;
         }
+        else
+        {
+            switch(i2c_addr)
+            {
+                case 0x08:
+                    pass = bus->i2c_smbus_write_quick(i2c_addr, I2C_SMBUS_WRITE);
+                    break;
+            }
+        }
+    }
+
+    return(pass);
+}
+
+bool TestForPalitGPUv2Controller(i2c_smbus_interface* bus, uint8_t i2c_addr)
+{
+    bool pass = false;
+
+    if(bus->info.port_id == 1)
+    {
+        switch(i2c_addr)
+        {
+            case 0x49:
+                s32 data        = bus->i2c_smbus_read_byte_data(i2c_addr, 0x0);
+                s32 mode_data   = bus->i2c_smbus_read_byte_data(i2c_addr, 0xe0);
+                pass            = (data == 0x0) && (mode_data < 0x5);
+                break;
+        }
+    }
+
+    return(pass);
+}
+
+DetectedControllers DetectPalitGPUv1Controllers(i2c_smbus_interface* bus, uint8_t i2c_addr, const std::string& name)
+{
+    DetectedControllers detected_controllers;
+
+    if(TestForPalitGPUv1Controller(bus, i2c_addr))
+    {
+        PalitGPUv1Controller*     controller     = new PalitGPUv1Controller(bus, i2c_addr, name);
+        RGBController_PalitGPUv1* rgb_controller = new RGBController_PalitGPUv1(controller);
+
+        detected_controllers.push_back(rgb_controller);
     }
 
     return(detected_controllers);
 }
 
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce GTX 1060",    DetectPalitGPUControllers, NVIDIA_VEN, NVIDIA_GTX1060_DEV, NVIDIA_SUB_VEN, NVIDIA_GTX1060_DEV,     0x08);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce GTX 1070",    DetectPalitGPUControllers, NVIDIA_VEN, NVIDIA_GTX1070_DEV, NVIDIA_SUB_VEN, NVIDIA_GTX1070_DEV,     0x08);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce GTX 1070 Ti", DetectPalitGPUControllers, NVIDIA_VEN, NVIDIA_GTX1070TI_DEV, NVIDIA_SUB_VEN, NVIDIA_GTX1070TI_DEV, 0x08);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce GTX 1080",    DetectPalitGPUControllers, NVIDIA_VEN, NVIDIA_GTX1080_DEV, NVIDIA_SUB_VEN, NVIDIA_GTX1080_DEV,     0x08);
-REGISTER_I2C_PCI_DETECTOR("Palit GeForce GTX 1080 Ti", DetectPalitGPUControllers, NVIDIA_VEN, NVIDIA_GTX1080TI_DEV, NVIDIA_SUB_VEN, NVIDIA_GTX1080TI_DEV, 0x08);
+DetectedControllers DetectPalitGPUv2Controllers(i2c_smbus_interface* bus, uint8_t i2c_addr, const std::string& name)
+{
+    DetectedControllers detected_controllers;
+
+    if(TestForPalitGPUv2Controller(bus, i2c_addr))
+    {
+        PalitGPUv2Controller*     controller     = new PalitGPUv2Controller(bus, i2c_addr, name);
+        RGBController_PalitGPUv2* rgb_controller = new RGBController_PalitGPUv2(controller);
+
+        detected_controllers.push_back(rgb_controller);
+    }
+
+    return(detected_controllers);
+}
+
+/*---------------------------------------------------------*\
+| Register detectors for Palit GPU controllers              |
+| Uses the unified PalitGPUv1Controllers for all V1 protocol|
+| devices ( Gainward and Palit branded)                     |
+\*---------------------------------------------------------*/
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce GTX 1060",                     DetectPalitGPUv1Controllers,    NVIDIA_VEN, NVIDIA_GTX1060_DEV,         NVIDIA_SUB_VEN,     NVIDIA_GTX1060_DEV,                         0x08);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce GTX 1070",                     DetectPalitGPUv1Controllers,    NVIDIA_VEN, NVIDIA_GTX1070_DEV,         NVIDIA_SUB_VEN,     NVIDIA_GTX1070_DEV,                         0x08);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce GTX 1070 Ti",                  DetectPalitGPUv1Controllers,    NVIDIA_VEN, NVIDIA_GTX1070TI_DEV,       NVIDIA_SUB_VEN,     NVIDIA_GTX1070TI_DEV,                       0x08);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce GTX 1080",                     DetectPalitGPUv1Controllers,    NVIDIA_VEN, NVIDIA_GTX1080_DEV,         NVIDIA_SUB_VEN,     NVIDIA_GTX1080_DEV,                         0x08);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce GTX 1080 Ti",                  DetectPalitGPUv1Controllers,    NVIDIA_VEN, NVIDIA_GTX1080TI_DEV,       NVIDIA_SUB_VEN,     NVIDIA_GTX1080TI_DEV,                       0x08);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce GTX 1080 Phoenix",          DetectPalitGPUv1Controllers,    NVIDIA_VEN, NVIDIA_GTX1080_DEV,         GAINWARD_SUB_VEN,   GAINWARD_GTX_1080_PHOENIX,                  0x08);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce GTX 1080 Ti Phoenix",       DetectPalitGPUv1Controllers,    NVIDIA_VEN, NVIDIA_GTX1080TI_DEV,       GAINWARD_SUB_VEN,   GAINWARD_GTX_1080TI_PHOENIX,                0x08);
+
+/*---------------------------------------------------------*\
+| Register detectors for Palit V2 GPU controllers           |
+| (Gainward and PNY branded cards)                          |
+\*---------------------------------------------------------*/
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce GTX 1660 SUPER Ghost",      DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_GTX1660S_DEV,        NVIDIA_SUB_VEN,     NVIDIA_GTX1660S_DEV,                        0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 2070 SUPER Phantom",    DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX2070S_OC_DEV,     GAINWARD_SUB_VEN,   NVIDIA_RTX2070S_OC_DEV,                     0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 2080 Phoenix GS",       DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX2080_DEV,         GAINWARD_SUB_VEN,   NVIDIA_RTX2080_A_DEV,                       0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3060 Pegasus 12G",      DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3060_DEV,         NVIDIA_SUB_VEN,     NVIDIA_RTX3060_DEV,                         0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3070 Phantom",          DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3070_DEV,         GAINWARD_SUB_VEN,   GAINWARD_RTX_3070_PHANTOM,                  0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3070 Phoenix",          DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3070_DEV,         GAINWARD_SUB_VEN,   NVIDIA_RTX3070_DEV,                         0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3070 Ti Phoenix",       DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3070TI_DEV,       GAINWARD_SUB_VEN,   NVIDIA_RTX3070TI_DEV,                       0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3080 Phoenix",          DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3080_DEV,         GAINWARD_SUB_VEN,   NVIDIA_RTX3080_DEV,                         0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3080 Ti Phoenix",       DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3080TI_DEV,       GAINWARD_SUB_VEN,   NVIDIA_RTX3080TI_DEV,                       0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3090 Phoenix",          DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3090_DEV,         GAINWARD_SUB_VEN,   NVIDIA_RTX3090_DEV,                         0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 3090 Ti Phantom",       DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3090TI_DEV,       GAINWARD_SUB_VEN,   GAINWARD_RTX_3090TI_PHANTOM,                0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 4080 Phantom GS",       DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX4080_DEV,         GAINWARD_SUB_VEN,   GAINWARD_RTX_4080_PHANTOM_GS_SUB_DEV,       0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 4090 Phantom",          DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX4090_DEV,         GAINWARD_SUB_VEN,   GAINWARD_RTX_4090_PHANTOM_SUB_DEV,          0x49);
+REGISTER_I2C_PCI_DETECTOR("Gainward GeForce RTX 5080 Phoenix",          DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX5080_DEV,         GAINWARD_SUB_VEN,   GAINWARD_RTX_5080_PHOENIX_SUB_DEV,          0x49);
+
+/*---------------------------------------------------------*\
+| PNY GPU controllers (also Palit-manufactured)             |
+\*---------------------------------------------------------*/
+REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 2060 XLR8 OC EDITION",       DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX2060_TU104_DEV,   PNY_SUB_VEN,        PNY_RTX_2060_XLR8_OC_SUB_DEV,               0x49);
+REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3060 XLR8 Revel EPIC-X",     DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3060_DEV,         PNY_SUB_VEN,        PNY_RTX_3060_XLR8_REVEL_EPIC_X_SUB_DEV,     0x49);
+REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3070 XLR8 Revel EPIC-X",     DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3070_DEV,         PNY_SUB_VEN,        PNY_RTX_3070_XLR8_REVEL_EPIC_X_SUB_DEV,     0x49);
+REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3070 XLR8 Revel EPIC-X LHR", DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3070_LHR_DEV,     PNY_SUB_VEN,        PNY_RTX_3070_XLR8_REVEL_EPIC_X_LHR_SUB_DEV, 0x49);
+REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3080 XLR8 Revel EPIC-X",     DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3080_DEV,         PNY_SUB_VEN,        PNY_RTX_3080_XLR8_REVEL_EPIC_X_SUB_DEV,     0x49);
+REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3080 Ti XLR8 Revel EPIC-X",  DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3080TI_DEV,       PNY_SUB_VEN,        PNY_RTX_3080TI_XLR8_REVEL_EPIC_X_SUB_DEV,   0x49);
+REGISTER_I2C_PCI_DETECTOR("PNY GeForce RTX 3090 XLR8 Revel EPIC-X",     DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3090_DEV,         PNY_SUB_VEN,        PNY_RTX_3090_XLR8_REVEL_EPIC_X_SUB_DEV,     0x49);
+
+/*---------------------------------------------------------*\
+| Palit GPU controllers detected via PNY detector           |
+\*---------------------------------------------------------*/
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 2070 SUPER Jetstream",     DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX2070S_OC_DEV,     NVIDIA_SUB_VEN,     NVIDIA_RTX2070S_OC_DEV,                     0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3060",                     DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3060_DEV,         PALIT_SUB_VEN,      PALIT_RTX3060_SUB_DEV,                      0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3060 LHR",                 DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3060_LHR_DEV,     PALIT_SUB_VEN,      PALIT_RTX3060_LHR_SUB_DEV,                  0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3060 Ti",                  DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3060TI_DEV,       PALIT_SUB_VEN,      PALIT_RTX3060TI_SUB_DEV,                    0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3060 Ti LHR",              DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3060TI_LHR_DEV,   PALIT_SUB_VEN,      NVIDIA_RTX3060TI_LHR_DEV,                   0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3070",                     DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3070_DEV,         PALIT_SUB_VEN,      PALIT_RTX3070_SUB_DEV,                      0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3070 LHR",                 DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3070_LHR_DEV,     PALIT_SUB_VEN,      PALIT_RTX3070_LHR_SUB_DEV,                  0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3070 Ti",                  DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3070TI_DEV,       PALIT_SUB_VEN,      PALIT_RTX3070TI_SUB_DEV,                    0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3080",                     DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3080_DEV,         PALIT_SUB_VEN,      PALIT_RTX3080_SUB_DEV,                      0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3080 LHR",                 DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3080_LHR_DEV,     PALIT_SUB_VEN,      PALIT_RTX3080_LHR_SUB_DEV,                  0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3080 Ti",                  DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3080TI_DEV,       PALIT_SUB_VEN,      PALIT_RTX3080TI_SUB_DEV,                    0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3090",                     DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3090_DEV,         PALIT_SUB_VEN,      PALIT_RTX3090_SUB_DEV,                      0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3090 Gamerock",            DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3090_DEV,         PALIT_SUB_VEN,      PALIT_RTX3090_GAMEROCK_SUB_DEV,             0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 3090 Ti Gamerock",         DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX3090TI_DEV,       PALIT_SUB_VEN,      PALIT_RTX3090TI_GAMEROCK_SUB_DEV,           0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4070 Ti",                  DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX4070TI_DEV,       PALIT_SUB_VEN,      PALIT_RTX4070TI_SUB_DEV,                    0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4070 Ti Gamerock",         DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX4070TI_DEV,       PALIT_SUB_VEN,      PALIT_RTX4070TI_GAMEROCK_SUB_DEV,           0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4070 Ti SUPER GamingPro",  DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX4070TIS_DEV,      PALIT_SUB_VEN,      PALIT_RTX4080_GAMINGPRO_SUB_DEV,            0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4080 GamingPro",           DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX4080_DEV,         PALIT_SUB_VEN,      PALIT_RTX4080_GAMINGPRO_SUB_DEV,            0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4080 SUPER GamingPro",     DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX4080S_DEV,        PALIT_SUB_VEN,      PALIT_RTX4080_GAMINGPRO_SUB_DEV,            0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 4090 Gamerock",            DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX4090_DEV,         PALIT_SUB_VEN,      PALIT_RTX4090_GAMEROCK_SUB_DEV,             0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5060 Ti White OC 16GB",    DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX5060TI_DEV,       PALIT_SUB_VEN,      PALIT_RTX5060TI_WHITE_OC_16G_SUB_DEV,       0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5070 GamingPro",           DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX5070_DEV,         PALIT_SUB_VEN,      PALIT_RTX5070_GAMINGPRO_SUB_DEV,            0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5070 Ti GameRock",         DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX5070TI_DEV,       PALIT_SUB_VEN,      PALIT_RTX5070TI_GAMEROCK_SUB_DEV,           0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5070 Ti GamingPro",        DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX5070TI_DEV,       PALIT_SUB_VEN,      PALIT_RTX5070TI_GAMINGPRO_SUB_DEV,          0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5070 Ti GamingPro-S",      DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX5070TI_DEV,       PALIT_SUB_VEN,      PALIT_RTX5070TI_GAMINGPRO_S_SUB_DEV,        0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5080 GameRock",            DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX5080_DEV,         PALIT_SUB_VEN,      PALIT_RTX5080_GAMEROCK_SUB_DEV,             0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5080 GamingPro",           DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX5080_DEV,         PALIT_SUB_VEN,      PALIT_RTX5080_GAMINGPRO_SUB_DEV,            0x49);
+REGISTER_I2C_PCI_DETECTOR("Palit GeForce RTX 5090 Gamerock",            DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX5090_DEV,         PALIT_SUB_VEN,      PALIT_RTX5090_GAMEROCK_SUB_DEV,             0x49);
+REGISTER_I2C_PCI_DETECTOR("NVIDIA GeForce RTX 2060 SUPER",              DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX2060_TU106_DEV,   NVIDIA_SUB_VEN,     NVIDIA_RTX2060_TU106_DEV,                   0x49);
+REGISTER_I2C_PCI_DETECTOR("NVIDIA GeForce RTX 2080 SUPER",              DetectPalitGPUv2Controllers,    NVIDIA_VEN, NVIDIA_RTX2080S_DEV,        NVIDIA_SUB_VEN,     NVIDIA_RTX2080S_DEV,                        0x49);

Controllers/PalitGPUController/PalitGPUv1Controller.cpp

@@ -0,0 +1,77 @@
+/*---------------------------------------------------------*\
+| PalitGPUv1Controller.cpp                                  |
+|                                                           |
+|   Driver for Palit v1 GPU                                 |
+|                                                           |
+|   TheRogueZeta                                05 Nov 2020 |
+|   Manatsawin Hanmongkolchai                   11 Apr 2023 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include <cstring>
+#include "PalitGPUv1Controller.h"
+
+PalitGPUv1Controller::PalitGPUv1Controller(i2c_smbus_interface* bus, palit_gpu_dev_id dev, std::string dev_name)
+{
+    this->bus   = bus;
+    this->dev   = dev;
+    this->name  = dev_name;
+}
+
+PalitGPUv1Controller::~PalitGPUv1Controller()
+{
+
+}
+
+std::string PalitGPUv1Controller::GetDeviceLocation()
+{
+    std::string return_string(bus->info.device_name);
+    char addr[5];
+    snprintf(addr, 5, "0x%02X", dev);
+    return_string.append(", address ");
+    return_string.append(addr);
+    return("I2C: " + return_string);
+}
+
+std::string PalitGPUv1Controller::GetDeviceName()
+{
+    return(name);
+}
+
+unsigned char PalitGPUv1Controller::GetLEDRed()
+{
+    /*-----------------------------------------------------*\
+    | Read red color from register 0x03                     |
+    \*-----------------------------------------------------*/
+    return(bus->i2c_smbus_read_byte_data(dev, PALIT_V1_RED_REGISTER));
+}
+
+unsigned char PalitGPUv1Controller::GetLEDGreen()
+{
+    /*-----------------------------------------------------*\
+    | Read green color from register 0x04                   |
+    \*-----------------------------------------------------*/
+    return(bus->i2c_smbus_read_byte_data(dev, PALIT_V1_RED_REGISTER + 1));
+}
+
+unsigned char PalitGPUv1Controller::GetLEDBlue()
+{
+    /*-----------------------------------------------------*\
+    | Read blue color from register 0x05                    |
+    \*-----------------------------------------------------*/
+    return(bus->i2c_smbus_read_byte_data(dev, PALIT_V1_RED_REGISTER + 2));
+}
+
+void PalitGPUv1Controller::SetLEDColors(unsigned char red, unsigned char green, unsigned char blue)
+{
+    /*-----------------------------------------------------*\
+    | Write RGB colors and control byte using individual    |
+    | writes to registers 0x03, 0x04, 0x05, 0x06            |
+    \*-----------------------------------------------------*/
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V1_RED_REGISTER, red);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V1_RED_REGISTER + 1, green);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V1_RED_REGISTER + 2, blue);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V1_RED_REGISTER + 3, 0xFF);
+}

Controllers/PalitGPUController/PalitGPUv1Controller.h

@@ -1,9 +1,10 @@
 /*---------------------------------------------------------*\
-| GainwardGPUv1Controller.h                                 |
+| PalitGPUv1Controller.h                                    |
 |                                                           |
-|   Driver for Gainward v1 GPU                              |
+|   Driver for Palit v1 GPU                                 |
 |                                                           |
 |   TheRogueZeta                                05 Nov 2020 |
+|   Manatsawin Hanmongkolchai                   11 Apr 2023 |
 |                                                           |
 |   This file is part of the OpenRGB project                |
 |   SPDX-License-Identifier: GPL-2.0-or-later               |
@@ -14,22 +15,19 @@
 #include <string>
 #include "i2c_smbus.h"
 
-typedef unsigned char gainward_gpu_dev_id;
+typedef unsigned char palit_gpu_dev_id;
 
 enum
 {
     /* RGB Registers */
-    GAINWARD_RED_REGISTER                       = 0x03, /* Red Register */
-    GAINWARD_GREEN_REGISTER                     = 0x04, /* Green Register */
-    GAINWARD_BLUE_REGISTER                      = 0x05, /* Blue Register */
-    GAINWARD_06_REGISTER                        = 0x06, /* Unknown (Brightness/Mode?) Register */
+    PALIT_V1_RED_REGISTER                       = 0x03, /* Red Register */
 };
 
-class GainwardGPUv1Controller
+class PalitGPUv1Controller
 {
 public:
-    GainwardGPUv1Controller(i2c_smbus_interface* bus, gainward_gpu_dev_id, std::string dev_name);
-    ~GainwardGPUv1Controller();
+    PalitGPUv1Controller(i2c_smbus_interface* bus, palit_gpu_dev_id, std::string dev_name);
+    ~PalitGPUv1Controller();
 
     std::string   GetDeviceLocation();
     std::string   GetDeviceName();
@@ -38,13 +36,9 @@ public:
     unsigned char GetLEDGreen();
     unsigned char GetLEDBlue();
     void          SetLEDColors(unsigned char red, unsigned char green, unsigned char blue);
-    void          SetMode();
-
-    unsigned char GainwardGPURegisterRead(unsigned char reg);
-    void          GainwardGPURegisterWrite(unsigned char reg, unsigned char val);
 
 private:
     i2c_smbus_interface *   bus;
-    gainward_gpu_dev_id     dev;
+    palit_gpu_dev_id        dev;
     std::string             name;
 };

Controllers/PalitGPUController/PalitGPUv2Controller.cpp

@@ -0,0 +1,154 @@
+/*---------------------------------------------------------*\
+| PalitGPUv2Controller.cpp                                  |
+|                                                           |
+|   Driver for Palit v2 GPU (merged from Gainward v2 and    |
+|   PNY controllers)                                        |
+|                                                           |
+|   KundaPanda                                  04 Jan 2021 |
+|   KendallMorgan                               17 Oct 2021 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include <cstring>
+#include "PalitGPUv2Controller.h"
+
+PalitGPUv2Controller::PalitGPUv2Controller(i2c_smbus_interface* bus, palit_gpu_dev_id dev, std::string dev_name)
+{
+    this->bus   = bus;
+    this->dev   = dev;
+    this->name  = dev_name;
+}
+
+PalitGPUv2Controller::~PalitGPUv2Controller()
+{
+
+}
+
+std::string PalitGPUv2Controller::GetDeviceLocation()
+{
+    std::string return_string(bus->info.device_name);
+    char addr[5];
+    snprintf(addr, 5, "0x%02X", dev);
+    return_string.append(", address ");
+    return_string.append(addr);
+    return("I2C: " + return_string);
+}
+
+std::string PalitGPUv2Controller::GetDeviceName()
+{
+    return(name);
+}
+
+unsigned char PalitGPUv2Controller::GetLEDRed()
+{
+    return(bus->i2c_smbus_read_byte_data(dev, PALIT_V2_RED_REGISTER));
+}
+
+unsigned char PalitGPUv2Controller::GetLEDGreen()
+{
+    return(bus->i2c_smbus_read_byte_data(dev, PALIT_V2_GREEN_REGISTER));
+}
+
+unsigned char PalitGPUv2Controller::GetLEDBlue()
+{
+    return(bus->i2c_smbus_read_byte_data(dev, PALIT_V2_BLUE_REGISTER));
+}
+
+void PalitGPUv2Controller::WriteI2CData(u8 command, u8 length, u8* data)
+{
+    for (u8 i = 0; i < length; i++)
+    {
+        bus->i2c_smbus_write_byte_data(dev, command + i, data[i]);
+    }
+}
+
+void PalitGPUv2Controller::SetLEDColors(unsigned char red, unsigned char green, unsigned char blue, unsigned char color_register)
+{
+    switch (color_register)
+    {
+        default:
+            bus->i2c_smbus_write_byte_data(dev, PALIT_V2_RED_REGISTER, red);
+            bus->i2c_smbus_write_byte_data(dev, PALIT_V2_GREEN_REGISTER, green);
+            bus->i2c_smbus_write_byte_data(dev, PALIT_V2_BLUE_REGISTER, blue);
+            break;
+        case PALIT_V2_COLOR_REGISTER_SECONDARY:
+            bus->i2c_smbus_write_byte_data(dev, PALIT_V2_RED_SECONDARY_REGISTER, red);
+            bus->i2c_smbus_write_byte_data(dev, PALIT_V2_GREEN_SECONDARY_REGISTER, green);
+            bus->i2c_smbus_write_byte_data(dev, PALIT_V2_BLUE_SECONDARY_REGISTER, blue);
+            break;
+        case PALIT_V2_COLOR_REGISTER_TERTIARY:
+            bus->i2c_smbus_write_byte_data(dev, PALIT_V2_RED_TERTIARY_REGISTER, red);
+            bus->i2c_smbus_write_byte_data(dev, PALIT_V2_GREEN_TERTIARY_REGISTER, green);
+            bus->i2c_smbus_write_byte_data(dev, PALIT_V2_BLUE_TERTIARY_REGISTER, blue);
+            break;
+    }
+}
+
+void PalitGPUv2Controller::SetMode(unsigned char mode, unsigned char speed, unsigned char control_mode)
+{
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_MODE_REGISTER, mode);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_CONTROL_REGISTER, control_mode);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_SPEED_REGISTER, speed);
+}
+
+void PalitGPUv2Controller::SetDirection(unsigned char direction)
+{
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_MODE_DIRECTION_REGISTER, direction);
+}
+
+void PalitGPUv2Controller::SetBreathingSpeed(unsigned int speed)
+{
+    unsigned char lower = speed & 0xFF;
+    unsigned char upper = (speed >> 2 * 4) & 0xFF;
+
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_BREATHE_SPEED_REGISTER_A, lower);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_BREATHE_SPEED_SECONDARY_REGISTER_A, lower);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_BREATHE_SPEED_REGISTER_B, upper);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_BREATHE_SPEED_SECONDARY_REGISTER_B, upper);
+}
+
+void PalitGPUv2Controller::SetOff()
+{
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_MODE_REGISTER, 0);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_CONTROL_REGISTER, 0x00);
+}
+
+void PalitGPUv2Controller::SetCycle(unsigned char speed)
+{
+    u8 loop[] = {
+        0x01,  // Direction
+        0x00,  // ??
+        speed, // Speed
+        0x1F   // Somehow related to speed
+    };
+    loop[2] = speed;
+    WriteI2CData(PALIT_V2_MODE_REGISTER, sizeof(loop), loop);
+}
+
+void PalitGPUv2Controller::SetStrobe(unsigned char r, unsigned char g, unsigned char b, unsigned char speed, unsigned char brightness)
+{
+    u8 strobe[] = {
+        0x02,       // Strobe
+        0x00,       // Rise speed
+        speed,      // Cycle length/2
+        0x00,       // Off delay
+        r,          // R
+        g,          // G
+        b,          // B
+        brightness, // Peak brightness
+        0x05        // Fade speed
+    };
+    WriteI2CData(PALIT_V2_MODE_REGISTER, sizeof(strobe), strobe);
+}
+
+void PalitGPUv2Controller::SetDirect(unsigned char red, unsigned char green, unsigned char blue, unsigned char brightness)
+{
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_MODE_REGISTER, 0);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_CONTROL_REGISTER, 0x01);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_RED_REGISTER, red);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_BLUE_REGISTER, blue);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_GREEN_REGISTER, green);
+    bus->i2c_smbus_write_byte_data(dev, PALIT_V2_BRIGHTNESS_REGISTER, brightness);
+}

Controllers/PalitGPUController/PalitGPUv2Controller.h

@@ -0,0 +1,115 @@
+/*---------------------------------------------------------*\
+| PalitGPUv2Controller.h                                    |
+|                                                           |
+|   Driver for Palit v2 GPU (merged from Gainward v2 and    |
+|   PNY controllers)                                        |
+|                                                           |
+|   KundaPanda                                  04 Jan 2021 |
+|   KendallMorgan                               17 Oct 2021 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#pragma once
+
+#include <string>
+#include "i2c_smbus.h"
+
+typedef unsigned char palit_gpu_dev_id;
+
+enum
+{
+    /* Control Registers */
+    PALIT_V2_CONTROL_REGISTER                    = 0x60, /* Control Register (direct mode / software control) */
+
+    /* Breathing speed registers */
+    PALIT_V2_BREATHE_SPEED_REGISTER_A            = 0x62, /* Lower part of speed control for breathe effect */
+    PALIT_V2_BREATHE_SPEED_REGISTER_B            = 0x63, /* Upper part of speed control for breathe effect */
+    PALIT_V2_BREATHE_SPEED_SECONDARY_REGISTER_A  = 0x64, /* Lower part of speed control for breathe effect - prob. secondary color */
+    PALIT_V2_BREATHE_SPEED_SECONDARY_REGISTER_B  = 0x65, /* Upper part of speed control for breathe effect - prob. secondary color */
+
+    /* RGB Registers - Primary color */
+    PALIT_V2_RED_REGISTER                        = 0x6C, /* Red Register */
+    PALIT_V2_GREEN_REGISTER                      = 0x6D, /* Green Register */
+    PALIT_V2_BLUE_REGISTER                       = 0x6E, /* Blue Register */
+    PALIT_V2_BRIGHTNESS_REGISTER                 = 0x6F, /* Brightness Register */
+
+    /* RGB Registers - Secondary color */
+    PALIT_V2_RED_SECONDARY_REGISTER              = 0x70, /* Red Register 2 */
+    PALIT_V2_GREEN_SECONDARY_REGISTER            = 0x71, /* Green Register 2 */
+    PALIT_V2_BLUE_SECONDARY_REGISTER             = 0x72, /* Blue Register 2 */
+
+    /* Mode Registers */
+    PALIT_V2_MODE_REGISTER                       = 0xE0, /* Mode Register */
+    PALIT_V2_MODE_DIRECTION_REGISTER             = 0xE1, /* Mode direction Register */
+    PALIT_V2_SPEED_REGISTER                      = 0xE2, /* Mode speed Register */
+
+    /* RGB Registers - Tertiary color */
+    PALIT_V2_RED_TERTIARY_REGISTER               = 0xE4, /* Red Register 3 */
+    PALIT_V2_GREEN_TERTIARY_REGISTER             = 0xE5, /* Green Register 3 */
+    PALIT_V2_BLUE_TERTIARY_REGISTER              = 0xE6, /* Blue Register 3 */
+};
+
+/* Mode values for the hardware mode register */
+enum
+{
+    PALIT_V2_MODE_OFF                            = 0x00,
+    PALIT_V2_MODE_STATIC                         = 0x00,
+    PALIT_V2_MODE_CYCLE                          = 0x01,
+    PALIT_V2_MODE_STROBE                         = 0x02,
+};
+
+/* Mode identifiers for RGBController (unique values for switch statements) */
+enum
+{
+    PALIT_V2_MODE_ID_OFF                         = 0,
+    PALIT_V2_MODE_ID_DIRECT                      = 1,
+    PALIT_V2_MODE_ID_BREATHING                   = 2,
+    PALIT_V2_MODE_ID_CYCLE                       = 3,
+    PALIT_V2_MODE_ID_STROBE                      = 4,
+};
+
+enum
+{
+    PALIT_V2_COLOR_REGISTER_PRIMARY,
+    PALIT_V2_COLOR_REGISTER_SECONDARY,
+    PALIT_V2_COLOR_REGISTER_TERTIARY,
+};
+
+enum
+{
+    /* Software controlled direct mode */
+    PALIT_V2_STATIC_SOFTWARE                     = 0x01,
+    /* GPU controlled direct mode with breathing effect */
+    PALIT_V2_STATIC_BREATHING                    = 0x22,
+};
+
+class PalitGPUv2Controller
+{
+public:
+    PalitGPUv2Controller(i2c_smbus_interface* bus, palit_gpu_dev_id, std::string dev_name);
+    ~PalitGPUv2Controller();
+
+    std::string   GetDeviceLocation();
+    std::string   GetDeviceName();
+
+    unsigned char GetLEDRed();
+    unsigned char GetLEDGreen();
+    unsigned char GetLEDBlue();
+    void          SetLEDColors(unsigned char red, unsigned char green, unsigned char blue, unsigned char color_register = PALIT_V2_COLOR_REGISTER_PRIMARY);
+    void          SetMode(unsigned char mode, unsigned char speed, unsigned char direct_mode = PALIT_V2_STATIC_SOFTWARE);
+    void          SetBreathingSpeed(unsigned int speed);
+    void          SetDirection(unsigned char direction);
+    void          SetOff();
+    void          SetCycle(unsigned char speed);
+    void          SetStrobe(unsigned char r, unsigned char g, unsigned char b, unsigned char speed, unsigned char brightness);
+    void          SetDirect(unsigned char red, unsigned char green, unsigned char blue, unsigned char brightness);
+
+private:
+    i2c_smbus_interface *   bus;
+    palit_gpu_dev_id        dev;
+    std::string             name;
+
+    void            WriteI2CData(u8 command, u8 length, u8* data);
+};

Controllers/PalitGPUController/RGBController_PalitGPU.cpp

@@ -1,112 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_PalitGPU.cpp                                |
-|                                                           |
-|   RGBController for Palit GPU                             |
-|                                                           |
-|   Manatsawin Hanmongkolchai                   11 Apr 2023 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include "RGBController_PalitGPU.h"
-
-/**------------------------------------------------------------------*\
-    @name Palit GPU
-    @category GPU
-    @type I2C
-    @save :x:
-    @direct :white_check_mark:
-    @effects :x:
-    @detectors DetectPalitGPUControllers
-    @comment
-\*-------------------------------------------------------------------*/
-
-RGBController_PalitGPU::RGBController_PalitGPU(PalitGPUController* controller_ptr)
-{
-    controller              = controller_ptr;
-
-    name                    = controller->GetName();
-    vendor                  = "Palit";
-    description             = "Legacy Palit RGB GPU Device";
-    location                = controller->GetDeviceLocation();
-
-    type                    = DEVICE_TYPE_GPU;
-
-    mode Direct;
-    Direct.name             = "Direct";
-    Direct.value            = PALIT_GPU_MODE_DIRECT;
-    Direct.flags            = MODE_FLAG_HAS_PER_LED_COLOR;
-    Direct.color_mode       = MODE_COLORS_PER_LED;
-    modes.push_back(Direct);
-
-    SetupZones();
-
-    // Initialize active mode
-    active_mode = 0;
-}
-
-RGBController_PalitGPU::~RGBController_PalitGPU()
-{
-    Shutdown();
-
-    delete controller;
-}
-
-void RGBController_PalitGPU::SetupZones()
-{
-    /*---------------------------------------------------------*\
-    | This device only has one LED, so create a single zone and |
-    | LED for it                                                |
-    \*---------------------------------------------------------*/
-    zone* new_zone          = new zone();
-    led*  new_led           = new led();
-
-    new_zone->name          = "GPU Zone";
-    new_zone->type          = ZONE_TYPE_SINGLE;
-    new_zone->leds_min      = 1;
-    new_zone->leds_max      = 1;
-    new_zone->leds_count    = 1;
-
-    new_led->name           = "GPU LED";
-
-    /*---------------------------------------------------------*\
-    | Push the zone and LED on to device vectors                |
-    \*---------------------------------------------------------*/
-    leds.push_back(*new_led);
-    zones.push_back(*new_zone);
-    SetupColors();
-}
-
-void RGBController_PalitGPU::DeviceUpdateLEDs()
-{
-    DeviceUpdateMode();
-}
-
-void RGBController_PalitGPU::DeviceUpdateZoneLEDs(int /*zone*/)
-{
-    DeviceUpdateLEDs();
-}
-
-void RGBController_PalitGPU::DeviceUpdateSingleLED(int /*led*/)
-{
-    DeviceUpdateLEDs();
-}
-
-void RGBController_PalitGPU::DeviceUpdateMode()
-{
-    RGBColor      color = colors[0];
-    unsigned char r     = RGBGetRValue(color);
-    unsigned char g     = RGBGetGValue(color);
-    unsigned char b     = RGBGetBValue(color);
-
-    switch(modes[active_mode].value)
-    {
-        case PALIT_GPU_MODE_DIRECT:
-            controller->SetDirect(r, g, b);
-            break;
-
-        default:
-            break;
-    }
-}

Controllers/PalitGPUController/RGBController_PalitGPU.h

@@ -1,33 +0,0 @@
-/*---------------------------------------------------------*\
-| RGBController_PalitGPU.h                                  |
-|                                                           |
-|   RGBController for Palit GPU                             |
-|                                                           |
-|   Manatsawin Hanmongkolchai                   11 Apr 2023 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#pragma once
-
-#include "RGBController.h"
-#include "PalitGPUController.h"
-
-class RGBController_PalitGPU : public RGBController
-{
-public:
-    RGBController_PalitGPU(PalitGPUController* controller_ptr);
-    ~RGBController_PalitGPU();
-
-    void        SetupZones();
-
-    void        DeviceUpdateLEDs();
-    void        DeviceUpdateZoneLEDs(int zone);
-    void        DeviceUpdateSingleLED(int led);
-
-    void        DeviceUpdateMode();
-
-private:
-    PalitGPUController* controller;
-};

Controllers/PalitGPUController/RGBController_PalitGPUv1.cpp

@@ -0,0 +1,110 @@
+/*---------------------------------------------------------*\
+| RGBController_PalitGPUv1.cpp                              |
+|                                                           |
+|   RGBController for Palit v1 GPU                          |
+|                                                           |
+|   TheRogueZeta                                05 Nov 2020 |
+|   Manatsawin Hanmongkolchai                   11 Apr 2023 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include "RGBController_PalitGPUv1.h"
+
+/**------------------------------------------------------------------*\
+    @name Palit GPU v1
+    @category GPU
+    @type I2C
+    @save :x:
+    @direct :white_check_mark:
+    @effects :x:
+    @detectors DetectPalitGPUControllers
+    @comment
+\*-------------------------------------------------------------------*/
+
+RGBController_PalitGPUv1::RGBController_PalitGPUv1(PalitGPUv1Controller* controller_ptr)
+{
+    controller              = controller_ptr;
+
+    name                    = controller->GetDeviceName();
+    vendor                  = "Palit";
+    type                    = DEVICE_TYPE_GPU;
+    description             = "Palit GPU V1 Device";
+    location                = controller->GetDeviceLocation();
+
+    mode Direct;
+    Direct.name             = "Direct";
+    Direct.value            = 1;
+    Direct.flags            = MODE_FLAG_HAS_PER_LED_COLOR;
+    Direct.color_mode       = MODE_COLORS_PER_LED;
+    modes.push_back(Direct);
+
+    SetupZones();
+}
+
+RGBController_PalitGPUv1::~RGBController_PalitGPUv1()
+{
+    Shutdown();
+
+    delete controller;
+}
+
+void RGBController_PalitGPUv1::SetupZones()
+{
+    /*-----------------------------------------------------*\
+    | Set up zone                                           |
+    \*-----------------------------------------------------*/
+    zone palit_gpu_zone;
+    palit_gpu_zone.name              = "GPU";
+    palit_gpu_zone.type              = ZONE_TYPE_SINGLE;
+    palit_gpu_zone.leds_min          = 1;
+    palit_gpu_zone.leds_max          = 1;
+    palit_gpu_zone.leds_count        = 1;
+    zones.push_back(palit_gpu_zone);
+
+    /*-----------------------------------------------------*\
+    | Set up LED                                            |
+    \*-----------------------------------------------------*/
+    led palit_gpu_led;
+    palit_gpu_led.name               = "GPU";
+    leds.push_back(palit_gpu_led);
+
+    SetupColors();
+
+    /*-----------------------------------------------------*\
+    | Initialize color                                      |
+    \*-----------------------------------------------------*/
+    unsigned char red = controller->GetLEDRed();
+    unsigned char grn = controller->GetLEDGreen();
+    unsigned char blu = controller->GetLEDBlue();
+
+    colors[0] =  ToRGBColor(red, grn, blu);
+}
+
+void RGBController_PalitGPUv1::DeviceUpdateLEDs()
+{
+    for(std::size_t led = 0; led < colors.size(); led++)
+    {
+        unsigned char red = RGBGetRValue(colors[led]);
+        unsigned char grn = RGBGetGValue(colors[led]);
+        unsigned char blu = RGBGetBValue(colors[led]);
+
+        controller->SetLEDColors(red, grn, blu);
+    }
+}
+
+void RGBController_PalitGPUv1::DeviceUpdateZoneLEDs(int /*zone*/)
+{
+    DeviceUpdateLEDs();
+}
+
+void RGBController_PalitGPUv1::DeviceUpdateSingleLED(int /*led*/)
+{
+    DeviceUpdateLEDs();
+}
+
+void RGBController_PalitGPUv1::DeviceUpdateMode()
+{
+
+}

Controllers/PalitGPUController/RGBController_PalitGPUv1.h

@@ -1,9 +1,10 @@
 /*---------------------------------------------------------*\
-| RGBController_GainwardGPUv1.h                             |
+| RGBController_PalitGPUv1.h                                |
 |                                                           |
-|   RGBController for Gainward v1 GPU                       |
+|   RGBController for Palit v1 GPU                          |
 |                                                           |
 |   TheRogueZeta                                05 Nov 2020 |
+|   Manatsawin Hanmongkolchai                   11 Apr 2023 |
 |                                                           |
 |   This file is part of the OpenRGB project                |
 |   SPDX-License-Identifier: GPL-2.0-or-later               |
@@ -12,13 +13,13 @@
 #pragma once
 
 #include "RGBController.h"
-#include "GainwardGPUv1Controller.h"
+#include "PalitGPUv1Controller.h"
 
-class RGBController_GainwardGPUv1 : public RGBController
+class RGBController_PalitGPUv1 : public RGBController
 {
 public:
-    RGBController_GainwardGPUv1(GainwardGPUv1Controller* controller_ptr);
-    ~RGBController_GainwardGPUv1();
+    RGBController_PalitGPUv1(PalitGPUv1Controller* controller_ptr);
+    ~RGBController_PalitGPUv1();
 
     void        SetupZones();
 
@@ -29,7 +30,7 @@ public:
     void        DeviceUpdateMode();
 
 private:
-    GainwardGPUv1Controller* controller;
+    PalitGPUv1Controller* controller;
 
     int        GetDeviceMode();
 };