Fix Corsair K70 RGB PRO V2 direct lighting

The K70 RGB PRO V2 (1B1C:1BB3) was detected but never lit: it blanked into software render mode and then fell back to its onboard effect. Getting it working turned up five faults, three of which affect every Corsair V2 device rather than just this keyboard. Packet size is now read from the HID report descriptor before the first write instead of being inferred from a reply. These devices come in a 64 byte and a 1024 byte flavour, and sending a short packet to a 1024 byte endpoint stalls it until the device is power cycled, so the size has to be known up front rather than after two short queries have gone out. CORSAIR_V2_PACKET_SIZE was 1024 while pkt_sze reached 1025, so every read using pkt_sze overran its stack buffer by a byte. The command helpers now use pkt_sze against buffers of the corrected size. The lighting resource probe ran before the device was placed in software render mode, where the answer is meaningless, and treated any error as "use resource 1". Devices that answer invalid or unsupported for resource 1 want the alternate lighting resource, which takes RGB triplets; this keyboard is one of them. The probe now runs after the render mode switch and distinguishes a stale open handle from an unsupported resource. Direct lighting writes were sized from the keymap, which covers only the keys that exist. The hardware expects its full slot count and ignores a short write, so corsair_v2_device carries an optional hw_led_count and the buffer map is padded to it. Set to 193 for this keyboard. The keepalive thread wrote LEDs on its first pass, because last_update_time was left at the clock epoch and so always read as older than the update period. That raced detection on the same HID handle with no locking, which both corrupted the transaction and could abort the process. The clock is now started before the thread runs, device transactions are serialised behind a mutex, and the thread is stopped before Shutdown rather than after. Also fixes an uninitialised stack buffer sent to the device during setup, and widens the K70 RGB PRO matrix to 22 columns so the numpad period key has a position in the layout instead of being dropped. Verified on hardware: repeated colour changes apply and the device stays responsive across runs. Co-Authored-By: Claude Opus 5 <[email protected]>
Add Corsair K60 RGB PRO SE support
2026-09-21 21:08:51 -04:00 · 2026-09-21 12:01:20 -05:00 · 2026-09-21 07:20:47 -05:00 · 2026-09-21 07:20:14 +02:00 · 2026-09-20 23:20:08 -05:00 · 2026-09-21 03:26:28 +04:00
1086 changed files with 131599 additions and 48123 deletions
@@ -14,9 +14,9 @@
 #   run only if manually started to save CI minutes if      #
 #   GitLab hosted runners                                   #
 # * For commits to the CalcProgrammer1/OpenRGB repository,  #
-#   automatically run all jobs on the default branch,       #
-#   otherwise run them if the source is part of a merge     #
-#   request                                                 #
+#   automatically run all jobs on the default branch or     #
+#   tag builds, otherwise run them if the source is part    #
+#   of a merge request                                      #
 #-----------------------------------------------------------#
 .downstream_rules:
  rules:
@@ -26,7 +26,7 @@

 .upstream_rules:
  rules:
-  - if: '$CI_PROJECT_PATH == "CalcProgrammer1/OpenRGB" && ($CI_COMMIT_BRANCH == $CI_DEFAULT_BRANCH || $CI_PIPELINE_SOURCE == "merge_request_event")'
+  - if: '$CI_PROJECT_PATH == "CalcProgrammer1/OpenRGB" && ($CI_COMMIT_BRANCH == $CI_DEFAULT_BRANCH || $CI_COMMIT_TAG || $CI_PIPELINE_SOURCE == "merge_request_event")'
    when: on_success
  - !reference [.downstream_rules, rules]

@@ -51,7 +51,7 @@ before_script:
 # Supported Devices Build Target                            #
 #-----------------------------------------------------------#
 "Supported Devices":
-  image: registry.gitlab.com/openrgbdevelopers/openrgb-linux-ci-deb-builder:bookworm-amd64
+  image: registry.gitlab.com/openrgbdevelopers/openrgb-linux-ci-deb-builder:trixie-amd64
  tags:
  - linux
  - amd64
@@ -71,10 +71,10 @@ before_script:
    - !reference [.upstream_rules, rules]

 #-----------------------------------------------------------#
-# OpenRGB Common Appimage Build Steps                       #
+# OpenRGB Common AppImage Build Steps                       #
 #-----------------------------------------------------------#
 .hidden_appimage_script: &appimage_script_steps
-  image: registry.gitlab.com/openrgbdevelopers/openrgb-linux-ci-deb-builder:bookworm-${TGT_ARCH}
+  image: registry.gitlab.com/openrgbdevelopers/openrgb-linux-ci-deb-builder:trixie-${TGT_ARCH}
  tags:
  - linux
  - ${TGT_ARCH}
@@ -87,8 +87,6 @@ before_script:
    name: "${CI_PROJECT_NAME}_Linux_${TGT_NAME}_${CI_COMMIT_SHORT_SHA}"
    paths:
    - OpenRGB-${TGT_PATH}.AppImage
-    - 60-openrgb.rules
-    - README.md
    expire_in: 30 days

  rules:
@@ -290,13 +288,13 @@ before_script:
  <<: *debian_script_steps

 #-----------------------------------------------------------#
-# Linux (.rpm, F43) 64-bit Build Target                     #
+# Linux (.rpm) Fedora 44 amd64 Build Target                 #
 #-----------------------------------------------------------#
-"Linux 64 F43 rpm":
-  image: fedora:43
+"Linux amd64 .rpm (Fedora 44)":
+  image: fedora:44
  stage: build
  script:
-  - dnf install rpmdevtools dnf-plugins-core libcurl-devel qt5-qtbase-devel git wget -y
+  - dnf install rpmdevtools dnf-plugins-core libcurl-devel qt6-qtbase-devel git wget -y
  - 'wget -O hidapi-hotplug.zip https://gitlab.com/OpenRGBDevelopers/hidapi-hotplug/-/jobs/artifacts/master/download?job=Linux+64+F43+rpm'
  - unzip hidapi-hotplug.zip
  - dnf install ./*.rpm -y
@@ -312,7 +310,7 @@ before_script:
  - cd ${CI_PROJECT_DIR}

  artifacts:
-    name: "${CI_PROJECT_NAME}_Linux_64_rpm_${CI_COMMIT_SHORT_SHA}"
+    name: "${CI_PROJECT_NAME}_Linux_amd64_rpm_${CI_COMMIT_SHORT_SHA}"
    paths:
    - openrgb*.rpm
    expire_in: 30 days
@@ -320,6 +318,44 @@ before_script:
  rules:
    - !reference [.upstream_rules, rules]

+#-----------------------------------------------------------#
+# OpenRGB Common Flatpak Build Steps                        #
+#-----------------------------------------------------------#
+.hidden_flatpak_script: &flatpak_script_steps
+  image: ghcr.io/flathub-infra/flatpak-github-actions:kde-6.10
+  stage: build
+  tags:
+  - linux
+  - ${TGT_ARCH}
+  script:
+  - flatpak-builder --user --disable-rofiles-fuse --repo=build/repo build/flatpak-build flatpak/org.openrgb.OpenRGB.yaml
+  - flatpak build-bundle build/repo org.openrgb.OpenRGB.flatpak org.openrgb.OpenRGB
+
+  artifacts:
+    name: "${CI_PROJECT_NAME}_Linux_${TGT_ARCH}_Flatpak_${CI_COMMIT_SHORT_SHA}"
+    paths:
+    - org.openrgb.OpenRGB.flatpak
+    expire_in: 30 days
+
+  rules:
+    - !reference [.upstream_rules, rules]
+
+#-----------------------------------------------------------#
+# Linux Flatpak amd64 Build Target                          #
+#-----------------------------------------------------------#
+"Linux amd64 Flatpak":
+  variables:
+    TGT_ARCH: "amd64"
+  <<: *flatpak_script_steps
+
+#-----------------------------------------------------------#
+# Linux Flatpak arm64 Build Target                          #
+#-----------------------------------------------------------#
+"Linux arm64 Flatpak":
+  variables:
+    TGT_ARCH: "arm64"
+  <<: *flatpak_script_steps
+
 #-----------------------------------------------------------#
 # Debian i386 Bookworm test                                 #
 #-----------------------------------------------------------#
@@ -387,10 +423,10 @@ before_script:
  - !reference [.upstream_rules, rules]

 #-----------------------------------------------------------#
-# Fedora 64 v43 test                                        #
+# Fedora amd64 44 test                                      #
 #-----------------------------------------------------------#
-"Fedora 64 v43":
-  image: fedora:43
+"Fedora 64 44":
+  image: fedora:44
  stage: test
  script:
  - dnf install unzip wget -y
@@ -401,9 +437,9 @@ before_script:
  - openrgb --version
  - dnf5 -y remove openrgb
  dependencies:
-  - "Linux 64 F43 rpm"
+  - "Linux amd64 .rpm (Fedora 44)"
  needs:
-  - "Linux 64 F43 rpm"
+  - "Linux amd64 .rpm (Fedora 44)"
  rules:
  - !reference [.upstream_rules, rules]

@@ -536,10 +572,7 @@ before_script:
  - macos
  stage: build
  script:
-  - eval $(/opt/homebrew/bin/brew shellenv)
-  - qmake OpenRGB.pro
-  - make -j16
-  - macdeployqt OpenRGB.app -codesign=OpenRGB
+  - ./scripts/build-macos.sh qt6 arm

  artifacts:
    name: "${CI_PROJECT_NAME}_MacOS_ARM64_${CI_COMMIT_SHORT_SHA}"
@@ -555,10 +588,7 @@ before_script:
  - macos
  stage: build
  script:
-  - eval $(/opt/homebrew/bin/brew shellenv)
-  - /opt/homebrew/opt/qt@5/bin/qmake OpenRGB.pro
-  - make -j16
-  - /opt/homebrew/opt/qt@5/bin/macdeployqt OpenRGB.app -codesign=OpenRGB
+  - ./scripts/build-macos.sh qt5 arm

  artifacts:
    name: "${CI_PROJECT_NAME}_MacOS_Qt5_ARM64_${CI_COMMIT_SHORT_SHA}"
@@ -574,10 +604,7 @@ before_script:
  - macos
  stage: build
  script:
-  - eval $(/usr/local/bin/brew shellenv)
-  - arch -x86_64 /usr/local/bin/qmake OpenRGB.pro
-  - arch -x86_64 make -j16
-  - arch -x86_64 /usr/local/bin/macdeployqt OpenRGB.app -codesign=OpenRGB
+  - ./scripts/build-macos.sh qt6 intel

  artifacts:
    name: "${CI_PROJECT_NAME}_MacOS_Intel_${CI_COMMIT_SHORT_SHA}"
@@ -593,10 +620,7 @@ before_script:
  - macos
  stage: build
  script:
-  - eval $(/usr/local/bin/brew shellenv)
-  - arch -x86_64 /usr/local/opt/qt@5/bin/qmake OpenRGB.pro
-  - arch -x86_64 make -j16
-  - arch -x86_64 /usr/local/opt/qt@5/bin/macdeployqt OpenRGB.app -codesign=OpenRGB
+  - ./scripts/build-macos.sh qt5 intel

  artifacts:
    name: "${CI_PROJECT_NAME}_MacOS_Intel_Qt5_${CI_COMMIT_SHORT_SHA}"
@@ -22,13 +22,12 @@ CODEOWNERS @Calcprogrammer1
 /Controllers/BlinkyTapeController/
 /Controllers/CoolerMasterController/                        @Dr_No
 /Controllers/CorsairCommanderCoreController/
-/Controllers/CorsairDominatorPlatinumController/
+/Controllers/CorsairDRAMController/
 /Controllers/CorsairHydroController/
 /Controllers/CorsairHydroPlatinumController/
 /Controllers/CorsairLightingNodeController/
 /Controllers/CorsairPeripheralController/
 /Controllers/CorsairVengeanceController/
-/Controllers/CorsairVengeanceProController/
 /Controllers/CorsairWirelessController/
 /Controllers/CreativeController/
 /Controllers/CrucialController/
@@ -0,0 +1,158 @@
+/*---------------------------------------------------------*\
+| AutoStart-Flatpak.cpp                                     |
+|                                                           |
+|   Autostart implementation for Linux via Flatpak Portal   |
+|                                                           |
+|   Adam Honse <[email protected]>      04 Sep 2026 |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include "AutoStart-Flatpak.h"
+#include <gio/gio.h>
+
+AutoStart::AutoStart(std::string name)
+{
+    InitAutoStart(name);
+}
+
+void AutoStart::InitAutoStart(std::string name)
+{
+    app_name = name;
+}
+
+bool AutoStart::CallBackgroundPortal(bool enable, const AutoStartInfo& autostart_info)
+{
+    GError*             error           = nullptr;
+    GDBusConnection*    connection      = g_bus_get_sync(G_BUS_TYPE_SESSION, nullptr, &error);
+
+    if(!connection)
+    {
+        if(error)
+        {
+            g_error_free(error);
+        }
+
+        return false;
+    }
+
+    /*-----------------------------------------------------*\
+    | FreeDesktop Background Portal parameters              |
+    \*-----------------------------------------------------*/
+    const char*         bus_name        = "org.freedesktop.portal.Desktop";
+    const char*         object_path     = "/org/freedesktop/portal/desktop";
+    const char*         interface_name  = "org.freedesktop.portal.Background";
+    const char*         method_name     = "RequestBackground";
+
+    /*-----------------------------------------------------*\
+    | Build the options dictionary (vardict) required by    |
+    | the Portal                                            |
+    \*-----------------------------------------------------*/
+    GVariantBuilder     options_builder;
+    g_variant_builder_init(&options_builder, G_VARIANT_TYPE_VARDICT);
+
+    /*-----------------------------------------------------*\
+    | Reason shown to the user in the system settings /     |
+    | permission prompt                                     |
+    \*-----------------------------------------------------*/
+    std::string         reason_str      = "Allow " + app_name + " to launch automatically at startup.";
+    g_variant_builder_add(&options_builder, "{sv}", "reason", g_variant_new_string(reason_str.c_str()));
+
+    /*-----------------------------------------------------*\
+    | Toggle the autostart feature state                    |
+    \*-----------------------------------------------------*/
+    g_variant_builder_add(&options_builder, "{sv}", "autostart", g_variant_new_boolean(enable));
+
+    if(enable)
+    {
+        /*-------------------------------------------------*\
+        | Pass command-line arguments to the background     |
+        | request                                           |
+        \*-------------------------------------------------*/
+        GVariantBuilder arg_builder;
+        g_variant_builder_init(&arg_builder, G_VARIANT_TYPE("as"));
+
+        /*-------------------------------------------------*\
+        | Add the primary executable path inside the        |
+        | Flatpak sandbox                                   |
+        \*-------------------------------------------------*/
+        g_variant_builder_add(&arg_builder, "s", GetExePath().c_str());
+
+        /*-------------------------------------------------*\
+        | Append any additional arguments provided by       |
+        | OpenRGB's autostart config                        |
+        \*-------------------------------------------------*/
+        if(!autostart_info.args.empty())
+        {
+            g_variant_builder_add(&arg_builder, "s", autostart_info.args.c_str());
+        }
+
+        GVariant*   commandline_args    = g_variant_builder_end(&arg_builder);
+        g_variant_builder_add(&options_builder, "{sv}", "commandline", commandline_args);
+    }
+
+    /*-----------------------------------------------------*\
+    | An empty string window handle is used since this is a |
+    | background configuration request                      |
+    \*-----------------------------------------------------*/
+    const char*     parent_window       = "";
+    GVariant*       options             = g_variant_builder_end(&options_builder);
+
+    /*-----------------------------------------------------*\
+    | Bundle parameters: (s a{sv}) -> Parent window handle, |
+    | Options dictionary                                    |
+    \*-----------------------------------------------------*/
+    GVariant*       parameters          = g_variant_new("(s@a{sv})", parent_window, options);
+    GVariant*       reply;
+
+    reply = g_dbus_connection_call_sync(connection, bus_name, object_path, interface_name, method_name, parameters, G_VARIANT_TYPE("(o)"), G_DBUS_CALL_FLAGS_NONE, -1, nullptr, &error);
+
+    g_object_unref(connection);
+
+    if(error)
+    {
+        g_error_free(error);
+        return false;
+    }
+
+    if(reply)
+    {
+        g_variant_unref(reply);
+        return true;
+    }
+
+    return false;
+}
+
+bool AutoStart::EnableAutoStart(AutoStartInfo autostart_info)
+{
+    return CallBackgroundPortal(true, autostart_info);
+}
+
+bool AutoStart::DisableAutoStart()
+{
+    return CallBackgroundPortal(false);
+}
+
+bool AutoStart::IsAutoStartEnabled()
+{
+    /*-----------------------------------------------------*\
+    | The FreeDesktop Background Portal does not provide a  |
+    | stateless status getter.  Sandbox permissions are     |
+    | securely managed and persisted internally by the      |
+    | host's portal service.  To implement a true state     |
+    | track here, OpenRGB will need to manage a local       |
+    | boolean flag inside its own configuration files (e.g. |
+    | OpenRGB.json).                                        |
+    \*-----------------------------------------------------*/
+    return false;
+}
+
+std::string AutoStart::GetExePath()
+{
+    /*-----------------------------------------------------*\
+    | Flatpak applications always run from this specific    |
+    | exported path hierarchy                               |
+    \*-----------------------------------------------------*/
+    return "/app/bin/openrgb";
+}
@@ -0,0 +1,31 @@
+/*---------------------------------------------------------*\
+| AutoStart-Flatpak.h                                       |
+|                                                           |
+|   Autostart implementation for Linux via Flatpak Portal   |
+|                                                           |
+|   Adam Honse <[email protected]>      04 Sep 2026 |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#pragma once
+
+#include <string>
+#include "AutoStart.h"
+
+class AutoStart : public AutoStartInterface
+{
+public:
+    AutoStart(std::string name);
+
+    bool        DisableAutoStart();
+    bool        EnableAutoStart(AutoStartInfo autostart_info);
+    bool        IsAutoStartEnabled();
+    std::string GetExePath();
+
+private:
+    void        InitAutoStart(std::string name);
+    bool        CallBackgroundPortal(bool enable, const AutoStartInfo& autostart_info = {});
+    
+    std::string app_name;
+};
@@ -119,6 +119,21 @@ bool AutoStart::IsAutoStartEnabled()

 std::string AutoStart::GetExePath()
 {
+    /*-----------------------------------------------------*\
+    | When running from an AppImage, the AppImage runtime   |
+    | sets the APPIMAGE environment variable to the path of |
+    | the AppImage file itself.  /proc/self/exe would       |
+    | instead point at the extracted binary inside the      |
+    | temporary squashfs mount, which disappears once the   |
+    | AppImage is closed, so prefer APPIMAGE when it is set |
+    \*-----------------------------------------------------*/
+    const char* appimage_path = getenv("APPIMAGE");
+
+    if(appimage_path != NULL)
+    {
+        return(std::string(appimage_path));
+    }
+
    /*-----------------------------------------------------*\
    | Create the OpenRGB executable path                    |
    \*-----------------------------------------------------*/
@@ -134,6 +149,64 @@ std::string AutoStart::GetExePath()
 | Private Methods                                           |
 \*---------------------------------------------------------*/

+/*---------------------------------------------------------*\
+| Escape a single argument for use in a .desktop Exec=      |
+| field, per the Desktop Entry Specification.               |
+|                                                           |
+| Reserved characters must be escaped by wrapping the whole |
+| argument in double quotes and backslash-escaping the      |
+| quote/backquote/backslash/dollar characters, and any      |
+| literal '%' must be doubled to '%%'.                      |
+\*---------------------------------------------------------*/
+static std::string DesktopExecEscape(const std::string& arg)
+{
+    static const std::string reserved = " \t\n\"'`\\><~|&;$*?#()%";
+
+    bool needs_quotes = false;
+    for(char c : arg)
+    {
+        if(reserved.find(c) != std::string::npos)
+        {
+            needs_quotes = true;
+            break;
+        }
+    }
+
+    std::string escaped;
+
+    if(needs_quotes)
+    {
+        escaped += '"';
+    }
+
+    for(char c : arg)
+    {
+        switch(c)
+        {
+            case '"':
+            case '`':
+            case '\\':
+            case '$':
+                escaped += '\\';
+                escaped += c;
+                break;
+            case '%':
+                escaped += "%%";
+                break;
+            default:
+                escaped += c;
+                break;
+        }
+    }
+
+    if(needs_quotes)
+    {
+        escaped += '"';
+    }
+
+    return(escaped);
+}
+
 std::string AutoStart::GenerateDesktopFile(AutoStartInfo autostart_info)
 {
    /*-----------------------------------------------------*\
@@ -154,11 +227,17 @@ std::string AutoStart::GenerateDesktopFile(AutoStartInfo autostart_info)
    /*-----------------------------------------------------*\
    | Add the executable path and arguments                 |
    \*-----------------------------------------------------*/
-    fileContents << "Exec="              << autostart_info.path;
+    fileContents << "Exec="              << DesktopExecEscape(autostart_info.path);

    if (autostart_info.args != "")
    {
-        fileContents << " " << autostart_info.args;
+        std::istringstream arg_parser(autostart_info.args);
+        std::string arg;
+
+        while(arg_parser >> arg)
+        {
+            fileContents << " " << DesktopExecEscape(arg);
+        }
    }

    fileContents << std::endl;
@@ -137,6 +137,43 @@ std::string AutoStart::GetExePath()
 | Private Methods                                           |
 \*---------------------------------------------------------*/

+/*---------------------------------------------------------*\
+| Escape a string for embedding inside an XML element       |
+| (used by the .plist generator) to avoid producing         |
+| malformed property list files.                            |
+\*---------------------------------------------------------*/
+static std::string XmlEscape(const std::string& input)
+{
+    std::string escaped;
+
+    for(char c : input)
+    {
+        switch(c)
+        {
+            case '&':
+                escaped += "&amp;";
+                break;
+            case '<':
+                escaped += "&lt;";
+                break;
+            case '>':
+                escaped += "&gt;";
+                break;
+            case '"':
+                escaped += "&quot;";
+                break;
+            case '\'':
+                escaped += "&apos;";
+                break;
+            default:
+                escaped += c;
+                break;
+        }
+    }
+
+    return(escaped);
+}
+
 std::string AutoStart::GenerateLaunchAgentFile(AutoStartInfo autostart_info)
 {
    /*-----------------------------------------------------*\
@@ -153,7 +190,8 @@ std::string AutoStart::GenerateLaunchAgentFile(AutoStartInfo autostart_info)
    fileContents << "    <string>org.openrgb</string>"                                                                              << std::endl;
    fileContents << "    <key>ProgramArguments</key>"                                                                               << std::endl;
    fileContents << "    <array>"                                                                                                   << std::endl;
-    fileContents << "        <string>" << autostart_info.path << "</string>"                                                        << std::endl;
+    fileContents << "        <string>" << XmlEscape(autostart_info.path) << "</string>"
+                 << std::endl;

    if(autostart_info.args != "")
    {
@@ -162,7 +200,8 @@ std::string AutoStart::GenerateLaunchAgentFile(AutoStartInfo autostart_info)

        while(arg_parser >> arg)
        {
-            fileContents << "        <string>" << arg << "</string>"                                                                << std::endl;
+            fileContents << "        <string>" << XmlEscape(arg) << "</string>"
+                         << std::endl;
        }
    }

@@ -12,6 +12,7 @@
 #include <shlobj.h>
 #include "AutoStart-Windows.h"
 #include "LogManager.h"
+#include "StringUtils.h"
 #include "filesystem.h"
 #include "windows.h"

@@ -71,11 +72,11 @@ bool AutoStart::EnableAutoStart(AutoStartInfo autostart_info)
        HRESULT         result;
        IShellLinkW*    shellLink                   = NULL;

-        std::wstring    exepathw                    = utf8_decode(autostart_info.path);
-        std::wstring    argumentsw                  = utf8_decode(autostart_info.args);
-        std::wstring    startupfilepathw            = utf8_decode(autostart_file);
-        std::wstring    descriptionw                = utf8_decode(autostart_info.desc);
-        std::wstring    iconw                       = utf8_decode(autostart_info.path);
+        std::wstring    exepathw                    = StringUtils::string_to_wstring(autostart_info.path);
+        std::wstring    argumentsw                  = StringUtils::string_to_wstring(autostart_info.args);
+        std::wstring    startupfilepathw            = StringUtils::string_to_wstring(autostart_file);
+        std::wstring    descriptionw                = StringUtils::string_to_wstring(autostart_info.desc);
+        std::wstring    iconw                       = StringUtils::string_to_wstring(autostart_info.path);

        result                                      = CoCreateInstance(CLSID_ShellLink, NULL, CLSCTX_ALL, IID_IShellLinkW, (void**)&shellLink);

@@ -150,11 +151,16 @@ std::string AutoStart::GetExePath()
    /*-----------------------------------------------------*\
    | Create the OpenRGB executable path                    |
    \*-----------------------------------------------------*/
-    char exepath[MAX_PATH] = "";
+    wchar_t exepath[MAX_PATH] = L"";

-    DWORD count = GetModuleFileNameA(NULL, exepath, MAX_PATH);
+    DWORD count = GetModuleFileNameW(NULL, exepath, MAX_PATH);

-    return(std::string(exepath, (count > 0) ? count : 0));
+    if(count == 0)
+    {
+        return(std::string());
+    }
+
+    return(StringUtils::wstring_to_string(std::wstring(exepath, count)));
 }

 /*---------------------------------------------------------*\
@@ -164,43 +170,39 @@ std::string AutoStart::GetExePath()

 void AutoStart::InitAutoStart(std::string name)
 {
-    char startMenuPath[MAX_PATH];
+    wchar_t startMenuPath[MAX_PATH];

    autostart_name = name;

    /*-----------------------------------------------------*\
    | Get startup applications path                         |
    \*-----------------------------------------------------*/
-    HRESULT result = SHGetFolderPathA(NULL, CSIDL_PROGRAMS, NULL, 0, startMenuPath);
+    HRESULT result = SHGetFolderPathW(NULL, CSIDL_PROGRAMS, NULL, 0, startMenuPath);

    if(SUCCEEDED(result))
    {
-        autostart_file = std::string(startMenuPath);
+        std::string autostart_dir = StringUtils::wstring_to_string(startMenuPath);
+        autostart_dir += "\\Startup\\";

-        autostart_file += "\\Startup\\" + autostart_name + ".lnk";
+        /*-------------------------------------------------*\
+        | Create the directory if it doesn't exist          |
+        \*-------------------------------------------------*/
+        std::error_code ec;
+
+        bool success = true;
+
+        if(!filesystem::exists(autostart_dir))
+        {
+            success = filesystem::create_directories(autostart_dir, ec);
+        }
+
+        if(success)
+        {
+            autostart_file = autostart_dir + autostart_name + ".lnk";
+        }
    }
    else
    {
        autostart_file.clear();
    }
 }
-
-/*---------------------------------------------------------*\
-| Convert an UTF8 string to a wide Unicode String           |
-| (from wmi.cpp)                                            |
-\*---------------------------------------------------------*/
-std::wstring AutoStart::utf8_decode(const std::string& str)
-{
-    if(str.empty())
-    {
-        return std::wstring();
-    }
-
-    int size_needed = MultiByteToWideChar(CP_UTF8, 0, &str[0], (int) str.size(), nullptr, 0);
-
-    std::wstring wstrTo(size_needed, 0);
-
-    MultiByteToWideChar(CP_UTF8, 0, &str[0], (int) str.size(), &wstrTo[0], size_needed);
-
-    return(wstrTo);
-}
@@ -24,5 +24,4 @@ public:

 private:
    void            InitAutoStart(std::string name);
-    std::wstring    utf8_decode(const std::string& str);
 };
@@ -40,9 +40,15 @@ protected:
 #include "AutoStart-Windows.h"
 #endif

+#ifdef FLATPAK_BUILD
+#include "AutoStart-Flatpak.h"
+#endif
+
 #ifdef __linux__
+#ifndef FLATPAK_BUILD
 #include "AutoStart-Linux.h"
 #endif
+#endif

 #ifdef __APPLE__
 #include "AutoStart-MacOS.h"
@@ -69,3 +69,7 @@ OpenRGB is written in C++, uses the Qt framework for UI, and uses the QMake buil

 Translation files are located in [`OpenRGB/qt/i18n/`](https://gitlab.com/CalcProgrammer1/OpenRGB/-/tree/master/qt/i18n), where languages are formatted using ISO 639-1 format: `OpenRGB_xx_XX.ts` — `xx_XX` representing the language code.
 In order to translate a file, you need to [fork](https://gitlab.com/CalcProgrammer1/OpenRGB/-/forks/new) the project, create a new file for your language with `lupdate` (or edit an exisiting one), edit the file with `qtlinguist`, commit, push, and create a merge request.
+
+## AI Guidelines
+
+OpenRGB is an open source project developed by humans for humans.  As a general rule, AI generated submissions are not permitted.  The licensing behind AI generated code is problematic.  If you choose to use AI for assistance in your development process, we can't stop you, but do not credit the AI in commits (no AI authorship/co-authorship).  Ultimately, you as a human developer are responsible for the code you submit and it is expected that any code you submit you fully understand and have manually vetted before submission.  Merge requests that appear to be straight from an AI output, commits with AI tool authorship or co-authorship tags, or otherwise AI generated submissions are subject to closure.
@@ -1,66 +0,0 @@
-/*---------------------------------------------------------*\
-| A4TechDetector.cpp                                        |
-|                                                           |
-|   Detector for A4Tech Devices                             |
-|                                                           |
-|   Chris M (Dr_No)                             30 Jun 2022 |
-|   Mohammed Julfikar Ali Mahbub (o-julfikar)   01 Apr 2024 |
-|                                                           |
-|   This file is part of the OpenRGB project                |
-|   SPDX-License-Identifier: GPL-2.0-or-later               |
-\*---------------------------------------------------------*/
-
-#include <hidapi.h>
-#include "BloodyB820RController.h"
-#include "BloodyMouseController.h"
-#include "DetectionManager.h"
-#include "RGBController_BloodyB820R.h"
-#include "RGBController_BloodyMouse.h"
-
-/*---------------------------------------------------------*\
-| A4 Tech USB vendor ID                                     |
-\*---------------------------------------------------------*/
-#define A4_TECH_VID                                 0x09DA
-
-DetectedControllers DetectA4TechMouseControllers(hid_device_info* info, const std::string& name)
-{
-    DetectedControllers detected_controllers;
-    hid_device*         dev;
-
-    dev = hid_open_path(info->path);
-
-    if(dev)
-    {
-        BloodyMouseController*     controller       = new BloodyMouseController(dev, info->path, info->product_id, name);
-        RGBController_BloodyMouse* rgb_controller   = new RGBController_BloodyMouse(controller);
-
-        detected_controllers.push_back(rgb_controller);
-    }
-
-    return(detected_controllers);
-}
-
-DetectedControllers DetectBloodyB820R(hid_device_info* info, const std::string& name)
-{
-    DetectedControllers detected_controllers;
-    hid_device*         dev;
-
-    dev = hid_open_path(info->path);
-
-    if(dev)
-    {
-        BloodyB820RController*     controller     = new BloodyB820RController(dev, info->path, name);
-        RGBController_BloodyB820R* rgb_controller = new RGBController_BloodyB820R(controller);
-
-        detected_controllers.push_back(rgb_controller);
-    }
-
-    return(detected_controllers);
-}
-
-REGISTER_HID_DETECTOR_IPU("Bloody W60 Pro",  DetectA4TechMouseControllers,       A4_TECH_VID,    BLOODY_W60_PRO_PID,     2,      0xFF33,     0x0529);
-REGISTER_HID_DETECTOR_IPU("Bloody W70 Max",  DetectA4TechMouseControllers,       A4_TECH_VID,    BLOODY_W70_MAX_PID,     2,      0xFF33,     0x0518);
-REGISTER_HID_DETECTOR_IPU("Bloody W90 Max",  DetectA4TechMouseControllers,       A4_TECH_VID,    BLOODY_W90_MAX_PID,     2,      0xFF33,     0x053D);
-REGISTER_HID_DETECTOR_IPU("Bloody W90 Pro",  DetectA4TechMouseControllers,       A4_TECH_VID,    BLOODY_W90_PRO_PID,     2,      0xFF33,     0x054D);
-REGISTER_HID_DETECTOR_IPU("Bloody MP 50RS",  DetectA4TechMouseControllers,       A4_TECH_VID,    BLOODY_MP_50RS_PID,     2,      0xFFF2,     0x6009);
-REGISTER_HID_DETECTOR_IPU("Bloody B820R",    DetectBloodyB820R,                  A4_TECH_VID,    BLOODY_B820R_PID,       2,      0xFF52,     0x0210);
@@ -0,0 +1,40 @@
+/*---------------------------------------------------------*\
+| BloodyB820RControllerDetect.cpp                           |
+|                                                           |
+|   Detector for Bloody B820R Devices                       |
+|                                                           |
+|   Mohammed Julfikar Ali Mahbub (o-julfikar)   01 Apr 2024 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include <hidapi.h>
+#include "BloodyB820RController.h"
+#include "DetectionManager.h"
+#include "RGBController_BloodyB820R.h"
+
+/*---------------------------------------------------------*\
+| A4 Tech USB vendor ID                                     |
+\*---------------------------------------------------------*/
+#define A4_TECH_VID                                 0x09DA
+
+DetectedControllers DetectBloodyB820R(hid_device_info* info, const std::string& name)
+{
+    DetectedControllers detected_controllers;
+    hid_device*         dev;
+
+    dev = hid_open_path(info->path);
+
+    if(dev)
+    {
+        BloodyB820RController*     controller     = new BloodyB820RController(dev, info->path, name);
+        RGBController_BloodyB820R* rgb_controller = new RGBController_BloodyB820R(controller);
+
+        detected_controllers.push_back(rgb_controller);
+    }
+
+    return(detected_controllers);
+}
+
+REGISTER_HID_DETECTOR_IPU("Bloody B820R", DetectBloodyB820R, A4_TECH_VID, BLOODY_B820R_PID, 2, 0xFF52, 0x0210);
@@ -173,6 +173,8 @@ RGBController_BloodyB820R::RGBController_BloodyB820R(BloodyB820RController *cont

 RGBController_BloodyB820R::~RGBController_BloodyB820R()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -0,0 +1,44 @@
+/*---------------------------------------------------------*\
+| BloodyMouseControllerDetect.cpp                           |
+|                                                           |
+|   Detector for Bloody Mouse Devices                       |
+|                                                           |
+|   Chris M (Dr_No)                             30 Jun 2022 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include <hidapi.h>
+#include "BloodyMouseController.h"
+#include "DetectionManager.h"
+#include "RGBController_BloodyMouse.h"
+
+/*---------------------------------------------------------*\
+| A4 Tech USB vendor ID                                     |
+\*---------------------------------------------------------*/
+#define A4_TECH_VID                                 0x09DA
+
+DetectedControllers DetectBloodyMouseControllers(hid_device_info* info, const std::string& name)
+{
+    DetectedControllers detected_controllers;
+    hid_device*         dev;
+
+    dev = hid_open_path(info->path);
+
+    if(dev)
+    {
+        BloodyMouseController*     controller       = new BloodyMouseController(dev, info->path, info->product_id, name);
+        RGBController_BloodyMouse* rgb_controller   = new RGBController_BloodyMouse(controller);
+
+        detected_controllers.push_back(rgb_controller);
+    }
+
+    return(detected_controllers);
+}
+
+REGISTER_HID_DETECTOR_IPU("Bloody W60 Pro",  DetectBloodyMouseControllers,  A4_TECH_VID,    BLOODY_W60_PRO_PID, 2,  0xFF33, 0x0529);
+REGISTER_HID_DETECTOR_IPU("Bloody W70 Max",  DetectBloodyMouseControllers,  A4_TECH_VID,    BLOODY_W70_MAX_PID, 2,  0xFF33, 0x0518);
+REGISTER_HID_DETECTOR_IPU("Bloody W90 Max",  DetectBloodyMouseControllers,  A4_TECH_VID,    BLOODY_W90_MAX_PID, 2,  0xFF33, 0x053D);
+REGISTER_HID_DETECTOR_IPU("Bloody W90 Pro",  DetectBloodyMouseControllers,  A4_TECH_VID,    BLOODY_W90_PRO_PID, 2,  0xFF33, 0x054D);
+REGISTER_HID_DETECTOR_IPU("Bloody MP 50RS",  DetectBloodyMouseControllers,  A4_TECH_VID,    BLOODY_MP_50RS_PID, 2,  0xFFF2, 0x6009);
@@ -89,6 +89,8 @@ RGBController_BloodyMouse::RGBController_BloodyMouse(BloodyMouseController *cont

 RGBController_BloodyMouse::~RGBController_BloodyMouse()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -44,6 +44,8 @@ RGBController_AMBX::RGBController_AMBX(AMBXController* controller_ptr)

 RGBController_AMBX::~RGBController_AMBX()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -132,6 +132,8 @@ RGBController_AMDWraithPrism::RGBController_AMDWraithPrism(AMDWraithPrismControl

 RGBController_AMDWraithPrism::~RGBController_AMDWraithPrism()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -31,7 +31,7 @@ AOCKeyboardController::~AOCKeyboardController()

 std::string AOCKeyboardController::GetDeviceLocation()
 {
-    return("HID " + location);
+    return("HID: " + location);
 }

 std::string AOCKeyboardController::GetDeviceName()
@@ -257,6 +257,8 @@ RGBController_AOCKeyboard::RGBController_AOCKeyboard(AOCKeyboardController* cont

 RGBController_AOCKeyboard::~RGBController_AOCKeyboard()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -27,7 +27,7 @@ AOCMouseController::~AOCMouseController()

 std::string AOCMouseController::GetDeviceLocation()
 {
-    return("HID " + location);
+    return("HID: " + location);
 }

 std::string AOCMouseController::GetDeviceName()
@@ -123,6 +123,8 @@ RGBController_AOCMouse::RGBController_AOCMouse(AOCMouseController* controller_pt

 RGBController_AOCMouse::~RGBController_AOCMouse()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -27,7 +27,7 @@ AOCMousematController::~AOCMousematController()

 std::string AOCMousematController::GetDeviceLocation()
 {
-    return("HID " + location);
+    return("HID: " + location);
 }

 std::string AOCMousematController::GetDeviceName()
@@ -113,6 +113,8 @@ RGBController_AOCMousemat::RGBController_AOCMousemat(AOCMousematController* cont

 RGBController_AOCMousemat::~RGBController_AOCMousemat()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -191,7 +191,7 @@ void PolychromeUSBController::SetDeviceInfo()
    WriteRGSwap(rgswap_final[0], rgswap_final[1], rgswap_final[2], rgswap_final[3], rgswap_final[4], rgswap_final[5], rgswap_final[6], rgswap_final[7]);
 }

-void PolychromeUSBController::DeviceResizeZone(int zone, int new_size)
+void PolychromeUSBController::SetZoneSize(int zone, int new_size)
 {
    unsigned char zonecfg[POLYCHROME_USB_ZONE_MAX_NUM];

@@ -135,7 +135,7 @@ public:
                                                    unsigned int    configsize
                                                    );

-    void                                        DeviceResizeZone(int zone, int new_size);
+    void                                        SetZoneSize(int zone, int new_size);
    void                                        SetRGSwap(bool reset);

 protected:
@@ -185,8 +185,25 @@ RGBController_PolychromeUSB::RGBController_PolychromeUSB(PolychromeUSBController
    SetupZones();
 }

+RGBController_PolychromeUSB::~RGBController_PolychromeUSB()
+{
+    Shutdown();
+
+    delete controller;
+}
+
 void RGBController_PolychromeUSB::SetupZones()
 {
+    /*-----------------------------------------------------*\
+    | Only set LED count on the first run                   |
+    \*-----------------------------------------------------*/
+    bool first_run = false;
+
+    if(zones.size() == 0)
+    {
+        first_run = true;
+    }
+
    /*-------------------------------------------------*\
    | Clear any existing color/LED configuration        |
    \*-------------------------------------------------*/
@@ -197,35 +214,62 @@ void RGBController_PolychromeUSB::SetupZones()
    /*-------------------------------------------------*\
    | Set zones and leds                                |
    \*-------------------------------------------------*/
-    for(unsigned int channel_idx = 0; channel_idx < zones.size(); channel_idx++)
+    for(std::size_t channel_idx = 0; channel_idx < zones.size(); channel_idx++)
    {
        PolychromeDeviceInfo device_info = controller->GetPolychromeDevices()[channel_idx];

-        zones[channel_idx].type     = ZONE_TYPE_LINEAR;
-
        if(device_info.device_type== PolychromeDeviceType::ADDRESSABLE)
        {
-            zones[channel_idx].name       = polychrome_USB_zone_names[device_info.zone_type];
-            zones[channel_idx].leds_min   = 0;
-            zones[channel_idx].leds_max   = ASROCK_ADDRESSABLE_MAX_LEDS;
-            zones[channel_idx].leds_count = device_info.num_leds;
+            zones[channel_idx].leds_min                 = 0;
+            zones[channel_idx].leds_max                 = ASROCK_ADDRESSABLE_MAX_LEDS;
+
+            if(first_run)
+            {
+                zones[channel_idx].flags                = ZONE_FLAG_MANUALLY_CONFIGURABLE_SIZE
+                                                        | ZONE_FLAG_MANUALLY_CONFIGURABLE_NAME
+                                                        | ZONE_FLAG_MANUALLY_CONFIGURABLE_TYPE
+                                                        | ZONE_FLAG_MANUALLY_CONFIGURABLE_MATRIX_MAP
+                                                        | ZONE_FLAG_MANUALLY_CONFIGURABLE_SEGMENTS;
+            }
+
+            if(!(zones[channel_idx].flags & ZONE_FLAG_MANUALLY_CONFIGURED_NAME))
+            {
+                zones[channel_idx].name                 = polychrome_USB_zone_names[device_info.zone_type];
+            }
+
+            if(!(zones[channel_idx].flags & ZONE_FLAG_MANUALLY_CONFIGURED_SIZE))
+            {
+                zones[channel_idx].leds_count           = device_info.num_leds;
+            }
+
+            if(!(zones[channel_idx].flags & ZONE_FLAG_MANUALLY_CONFIGURED_TYPE))
+            {
+                zones[channel_idx].type                 = ZONE_TYPE_LINEAR;
+            }
+
+            if(!(zones[channel_idx].flags & ZONE_FLAG_MANUALLY_CONFIGURED_MATRIX_MAP))
+            {
+                zones[channel_idx].matrix_map.width     = 0;
+                zones[channel_idx].matrix_map.height    = 0;
+                zones[channel_idx].matrix_map.map.resize(0);
+            }
        }
        else if(device_info.device_type==PolychromeDeviceType::FIXED)
        {
-            zones[channel_idx].name       = polychrome_USB_zone_names[device_info.zone_type];
-            zones[channel_idx].leds_min   = device_info.num_leds;
-            zones[channel_idx].leds_max   = device_info.num_leds;
-            zones[channel_idx].leds_count = device_info.num_leds;
+            zones[channel_idx].name                     = polychrome_USB_zone_names[device_info.zone_type];
+            zones[channel_idx].type                     = ZONE_TYPE_LINEAR;
+            zones[channel_idx].leds_min                 = device_info.num_leds;
+            zones[channel_idx].leds_max                 = device_info.num_leds;
+            zones[channel_idx].leds_count               = device_info.num_leds;
        }

-
        for(unsigned int led_ch_idx = 0; led_ch_idx < zones[channel_idx].leds_count; led_ch_idx++)
        {
            led new_led;
            new_led.name = zones[channel_idx].name;
            new_led.name.append(", LED ");
            new_led.name.append(std::to_string(led_ch_idx + 1));
-            new_led.value = channel_idx;
+            new_led.value = (unsigned int)channel_idx;

            leds.push_back(new_led);
        }
@@ -271,10 +315,14 @@ void RGBController_PolychromeUSB::SetupZones()
     }
 }

-void RGBController_PolychromeUSB::DeviceResizeZone(int zone, int new_size)
+void RGBController_PolychromeUSB::DeviceConfigureZone(int zone_idx)
 {
-    zones[zone].leds_count = (unsigned char) new_size;
-    controller->DeviceResizeZone(zones_info[zone].zone, new_size);
+    if((size_t)zone_idx < zones.size())
+    {
+        controller->SetZoneSize(zones_info[zone_idx].zone, zones[zone_idx].leds_count);
+
+        SetupZones();
+    }
 }

 void RGBController_PolychromeUSB::DeviceUpdateLEDs()
@@ -286,9 +334,14 @@ void RGBController_PolychromeUSB::DeviceUpdateLEDs()
    }
    for(std::size_t zone_idx = 0; zone_idx < zones.size(); zone_idx++)
    {
+        if(zones[zone_idx].leds_count == 0)
+        {
+            continue;
+        }
+
        unsigned char set_mode = zones_info[zone_idx].mode;

-        if (set_mode>modes.size())
+        if(set_mode>modes.size())
        {
            set_mode = active_mode;
        }
@@ -299,6 +352,11 @@ void RGBController_PolychromeUSB::DeviceUpdateLEDs()

 void RGBController_PolychromeUSB::DeviceUpdateZoneLEDs(int zone)
 {
+    if(zones[zone].leds_count == 0)
+    {
+        return;
+    }
+
    unsigned char set_mode=zones_info[zone].mode;

    if(set_mode > modes.size())
@@ -306,7 +364,7 @@ void RGBController_PolychromeUSB::DeviceUpdateZoneLEDs(int zone)
        set_mode = active_mode;
    }

-    controller->WriteZone(zone, set_mode, zones_info[zone].speed, zones[zone].colors[0], false);
+    controller->WriteZone((unsigned char)zone, set_mode, zones_info[zone].speed, zones[zone].colors[0], false);
 }

 void RGBController_PolychromeUSB::DeviceUpdateSingleLED(int led)
@@ -314,12 +372,17 @@ void RGBController_PolychromeUSB::DeviceUpdateSingleLED(int led)
    unsigned int  channel  = leds[led].value;
    unsigned char set_mode = zones_info[channel].mode;

+    if(zones[channel].leds_count == 0)
+    {
+        return;
+    }
+
    if(set_mode > modes.size())
    {
        set_mode = active_mode;
    }

-    controller->WriteZone(channel, set_mode, zones_info[channel].speed, zones[channel].colors[0], false);
+    controller->WriteZone((unsigned char)channel, set_mode, zones_info[channel].speed, zones[channel].colors[0], false);
 }

 unsigned char RGBController_PolychromeUSB::GetDeviceMode(unsigned char zone)
@@ -19,10 +19,11 @@ class RGBController_PolychromeUSB : public RGBController
 {
 public:
    RGBController_PolychromeUSB(PolychromeUSBController* controller_ptr);
+    ~RGBController_PolychromeUSB();

    void        SetupZones();

-    void        DeviceResizeZone(int zone, int new_size);
+    void        DeviceConfigureZone(int zone_idx);

    void        DeviceUpdateLEDs();
    void        DeviceUpdateZoneLEDs(int zone);
@@ -36,7 +36,7 @@ ASRockASRRGBSMBusController::~ASRockASRRGBSMBusController()

 std::string ASRockASRRGBSMBusController::GetDeviceLocation()
 {
-    std::string return_string(bus->device_name);
+    std::string return_string(bus->info.device_name);
    char addr[5];
    snprintf(addr, 5, "0x%02X", dev);
    return_string.append(", address ");
@@ -113,6 +113,8 @@ RGBController_ASRockASRRGBSMBus::RGBController_ASRockASRRGBSMBus(ASRockASRRGBSMB

 RGBController_ASRockASRRGBSMBus::~RGBController_ASRockASRRGBSMBus()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -159,13 +161,6 @@ void RGBController_ASRockASRRGBSMBus::SetupZones()
    SetupColors();
 }

-void RGBController_ASRockASRRGBSMBus::DeviceResizeZone(int /*zone*/, int /*new_size*/)
-{
-    /*---------------------------------------------------------*\
-    | This device does not support resizing zones               |
-    \*---------------------------------------------------------*/
-}
-
 void RGBController_ASRockASRRGBSMBus::DeviceUpdateLEDs()
 {
    for(unsigned int led = 0; led < colors.size(); led++)
@@ -22,8 +22,6 @@ public:

    void        SetupZones();

-    void        DeviceResizeZone(int zone, int new_size);
-
    void        DeviceUpdateLEDs();
    void        DeviceUpdateZoneLEDs(int zone);
    void        DeviceUpdateSingleLED(int led);
@@ -0,0 +1,199 @@
+/*---------------------------------------------------------*\
+| ASRockGPUSMBusController.cpp                              |
+|                                                           |
+|   Driver for ASRock GPU RGB controllers                   |
+|                                                           |
+|   Based on SignalRGB ASRock GPU.js plugin                 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include "ASRockGPUSMBusController.h"
+#include "LogManager.h"
+#include <chrono>
+#include <cstdio>
+#include <cstring>
+#include <thread>
+
+using namespace std::chrono_literals;
+
+ASRockGPUSMBusController::ASRockGPUSMBusController(i2c_smbus_interface* bus, asrock_gpu_dev_id dev, std::string name)
+{
+    this->bus          = bus;
+    this->dev          = dev;
+    this->device_name  = name;
+    this->num_channels = 0;
+
+    memset(enabled_channels, 0, sizeof(enabled_channels));
+    memset(led_counts, 0, sizeof(led_counts));
+}
+
+ASRockGPUSMBusController::~ASRockGPUSMBusController()
+{
+}
+
+std::string ASRockGPUSMBusController::GetDeviceLocation()
+{
+    std::string return_string(bus->info.device_name);
+    char addr[5];
+    snprintf(addr, 5, "0x%02X", dev);
+    return_string.append(", address ");
+    return_string.append(addr);
+    return("I2C: " + return_string);
+}
+
+std::string ASRockGPUSMBusController::GetDeviceName()
+{
+    return(device_name);
+}
+
+bool ASRockGPUSMBusController::WriteBlock(uint8_t command, uint8_t subcommand, const uint8_t* data, uint8_t len)
+{
+    /*-----------------------------------------------------*\
+    | SignalRGB packet format                              |
+    | [command, 0, subcommand, data...]                    |
+    | Uses pure I2C rather than SMBus                      |
+    \*-----------------------------------------------------*/
+    uint8_t packet[12];
+    memset(packet, 0, sizeof(packet));
+
+    packet[0] = command;
+    packet[1] = 0x00;
+    packet[2] = subcommand;
+
+    if(data != nullptr && len > 0)
+    {
+        uint8_t copy_len = (len > 9) ? 9 : len;
+        memcpy(&packet[3], data, copy_len);
+    }
+
+    int size   = 12;
+    int result = bus->i2c_write_block(dev, size, packet);
+
+    if(result < 0)
+    {
+        LOG_DEBUG("[ASRock GPU] Write block failed: %d", result);
+        return(false);
+    }
+
+    return(true);
+}
+
+bool ASRockGPUSMBusController::ReadBlock(uint8_t* response, uint8_t len)
+{
+    memset(response, 0, len);
+    int size   = len;
+    int result = bus->i2c_read_block(dev, &size, response);
+
+    if(result < 0)
+    {
+        LOG_DEBUG("[ASRock GPU] Read block failed: %d", result);
+        return(false);
+    }
+
+    return(true);
+}
+
+bool ASRockGPUSMBusController::DetectChannels()
+{
+    /*-----------------------------------------------------*\
+    | Get enabled channels                                 |
+    | Command 0x14, subcommand 0x01                        |
+    \*-----------------------------------------------------*/
+    if(!WriteBlock(0x14, 0x01, nullptr, 0))
+    {
+        LOG_WARNING("[ASRock GPU] Failed to request enabled channels");
+        return(false);
+    }
+
+    std::this_thread::sleep_for(20ms);
+
+    uint8_t response[I2C_SMBUS_BLOCK_MAX];
+    if(!ReadBlock(response, sizeof(response)))
+    {
+        LOG_WARNING("[ASRock GPU] Failed to read enabled channels");
+        return(false);
+    }
+
+    LOG_TRACE("[ASRock GPU] Enabled channels response: %02X %02X %02X %02X %02X %02X", response[0], response[1], response[2], response[3], response[4], response[5]);
+
+    /*-----------------------------------------------------*\
+    | Response format                                      |
+    | Bytes 4-5 contain the channel bitmap                 |
+    \*-----------------------------------------------------*/
+    uint16_t channel_bits = response[4] | (response[5] << 8);
+    LOG_TRACE("[ASRock GPU] Channel bits: 0x%04X", channel_bits);
+
+    /*-----------------------------------------------------*\
+    | Get LED counts                                       |
+    | Command 0x14, subcommand 0x02                        |
+    \*-----------------------------------------------------*/
+    if(!WriteBlock(0x14, 0x02, nullptr, 0))
+    {
+        LOG_WARNING("[ASRock GPU] Failed to request LED counts");
+        return(false);
+    }
+
+    std::this_thread::sleep_for(20ms);
+
+    if(!ReadBlock(response, sizeof(response)))
+    {
+        LOG_WARNING("[ASRock GPU] Failed to read LED counts");
+        return(false);
+    }
+
+    num_channels = 0;
+    for(int i = 0; i < 16; i++)
+    {
+        if(channel_bits & (1 << i))
+        {
+            enabled_channels[num_channels] = i;
+            led_counts[num_channels]       = response[4 + i];
+
+            const char* name = "Unknown";
+            if(i == ASROCK_GPU_CHANNEL_ARGB_HEADER)
+            {
+                name = "ARGB Header";
+            }
+            else if(i == ASROCK_GPU_CHANNEL_TOP_SIDE)
+            {
+                name = "Top Side";
+            }
+            else if(i == ASROCK_GPU_CHANNEL_FAN)
+            {
+                name = "Fan";
+            }
+
+            LOG_DEBUG("[ASRock GPU] Channel %d (%s) active with %d LEDs", i, name, response[4 + i]);
+            num_channels++;
+        }
+    }
+
+    LOG_DEBUG("[ASRock GPU] Found %d active channels", num_channels);
+    return(num_channels > 0);
+}
+
+void ASRockGPUSMBusController::SetChannelColor(uint8_t channel_idx, uint8_t red, uint8_t green, uint8_t blue)
+{
+    /*-----------------------------------------------------*\
+    | SignalRGB color packet                               |
+    | Command 0x10, subcommand is the channel index        |
+    \*-----------------------------------------------------*/
+    uint8_t data[8] =
+    {
+        0x01,  // Mode: direct/static
+        red,
+        green,
+        blue,
+        0x80,  // Effect speed
+        0xFF,  // Brightness
+        0x00,  // Effect direction
+        0x1A   // Unknown constant
+    };
+
+    if(!WriteBlock(0x10, channel_idx, data, sizeof(data)))
+    {
+        LOG_WARNING("[ASRock GPU] Failed to set color for channel %d", channel_idx);
+    }
+}
@@ -0,0 +1,55 @@
+/*---------------------------------------------------------*\
+| ASRockGPUSMBusController.h                                |
+|                                                           |
+|   Driver for ASRock GPU RGB controllers                   |
+|                                                           |
+|   Based on SignalRGB ASRock GPU.js plugin                 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#pragma once
+
+#include <string>
+#include "i2c_smbus.h"
+
+typedef uint8_t asrock_gpu_dev_id;
+
+#define ASROCK_GPU_CONTROLLER_NAME   "ASRock GPU SMBus Controller"
+#define ASROCK_GPU_SMBUS_ADDRESS     0x36
+
+/*-----------------------------------------------------*\
+| ASRock GPU Channel Names (from SignalRGB)             |
+\*-----------------------------------------------------*/
+enum
+{
+    ASROCK_GPU_CHANNEL_ARGB_HEADER  = 3,
+    ASROCK_GPU_CHANNEL_TOP_SIDE     = 6,
+    ASROCK_GPU_CHANNEL_FAN          = 7,
+};
+
+class ASRockGPUSMBusController
+{
+public:
+    ASRockGPUSMBusController(i2c_smbus_interface* bus, asrock_gpu_dev_id dev, std::string name);
+    ~ASRockGPUSMBusController();
+
+    std::string GetDeviceLocation();
+    std::string GetDeviceName();
+
+    void        SetChannelColor(uint8_t channel_idx, uint8_t red, uint8_t green, uint8_t blue);
+    bool        DetectChannels();
+
+    uint8_t     enabled_channels[16];
+    uint8_t     led_counts[16];
+    uint8_t     num_channels;
+
+private:
+    i2c_smbus_interface* bus;
+    asrock_gpu_dev_id    dev;
+    std::string          device_name;
+
+    bool        WriteBlock(uint8_t command, uint8_t subcommand, const uint8_t* data, uint8_t len);
+    bool        ReadBlock(uint8_t* response, uint8_t len);
+};
@@ -0,0 +1,47 @@
+/*---------------------------------------------------------*\
+| ASRockGPUSMBusControllerDetect.cpp                        |
+|                                                           |
+|   Detector for ASRock GPU RGB controllers                 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include "DetectionManager.h"
+#include "ASRockGPUSMBusController.h"
+#include "LogManager.h"
+#include "RGBController_ASRockGPUSMBus.h"
+#include "i2c_amd_gpu.h"
+#include "i2c_smbus.h"
+#include "pci_ids.h"
+
+DetectedControllers DetectASRockGPUSMBusControllers(i2c_smbus_interface* bus, uint8_t address, const std::string& name)
+{
+    DetectedControllers detected_controllers;
+
+    if(bus->info.pci_vendor == AMD_GPU_VEN && !is_amd_gpu_i2c_bus(bus))
+    {
+        return(detected_controllers);
+    }
+
+    LOG_DEBUG("[ASRock GPU] Checking GPU I2C bus for RGB controller at 0x%02X", address);
+
+    ASRockGPUSMBusController* controller = new ASRockGPUSMBusController(bus, address, name);
+
+    if(controller->DetectChannels())
+    {
+        detected_controllers.push_back(new RGBController_ASRockGPUSMBus(controller));
+    }
+    else
+    {
+        LOG_WARNING("[ASRock GPU] No active channels found, device not registered");
+        delete controller;
+    }
+
+    return(detected_controllers);
+}
+
+REGISTER_I2C_PCI_DETECTOR("ASRock Radeon RX 9070 XT Steel Legend",   DetectASRockGPUSMBusControllers, AMD_GPU_VEN, AMD_NAVI48_DEV, ASROCK_SUB_VEN, 0x5403, ASROCK_GPU_SMBUS_ADDRESS);
+REGISTER_I2C_PCI_DETECTOR("ASRock Radeon RX 9070 XT Steel Legend Dark", DetectASRockGPUSMBusControllers, AMD_GPU_VEN, AMD_NAVI48_DEV, ASROCK_SUB_VEN, 0x5414, ASROCK_GPU_SMBUS_ADDRESS);
+REGISTER_I2C_PCI_DETECTOR("ASRock Radeon RX 9070 XT Taichi 16GB OC", DetectASRockGPUSMBusControllers, AMD_GPU_VEN, AMD_NAVI48_DEV, ASROCK_SUB_VEN, 0x5401, ASROCK_GPU_SMBUS_ADDRESS);
+REGISTER_I2C_PCI_DETECTOR("ASRock Radeon RX 9060 XT Steel Legend",   DetectASRockGPUSMBusControllers, AMD_GPU_VEN, AMD_NAVI44_DEV, ASROCK_SUB_VEN, 0x5407, ASROCK_GPU_SMBUS_ADDRESS);
@@ -0,0 +1,140 @@
+/*---------------------------------------------------------*\
+| RGBController_ASRockGPUSMBus.cpp                          |
+|                                                           |
+|   RGBController for ASRock GPU RGB controllers            |
+|                                                           |
+|   Based on SignalRGB ASRock GPU.js plugin                 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include "RGBController_ASRockGPUSMBus.h"
+
+/**------------------------------------------------------------------*\
+    @name ASRock GPU SMBus
+    @category GPU
+    @type I2C
+    @save :x:
+    @direct :white_check_mark:
+    @effects :x:
+    @detectors DetectASRockGPUSMBusControllers
+    @comment
+\*-------------------------------------------------------------------*/
+
+RGBController_ASRockGPUSMBus::RGBController_ASRockGPUSMBus(ASRockGPUSMBusController* controller_ptr)
+{
+    controller  = controller_ptr;
+
+    name        = controller->GetDeviceName();
+    vendor      = "ASRock";
+    type        = DEVICE_TYPE_GPU;
+    description = "ASRock GPU RGB Controller";
+    location    = controller->GetDeviceLocation();
+
+    mode Direct;
+    Direct.name       = "Direct";
+    Direct.value      = 0;
+    Direct.flags      = MODE_FLAG_HAS_PER_LED_COLOR;
+    Direct.color_mode = MODE_COLORS_PER_LED;
+    modes.push_back(Direct);
+
+    SetupZones();
+}
+
+RGBController_ASRockGPUSMBus::~RGBController_ASRockGPUSMBus()
+{
+    Shutdown();
+
+    delete controller;
+}
+
+void RGBController_ASRockGPUSMBus::SetupZones()
+{
+    /*-----------------------------------------------------*\
+    | Set up zones - one zone per channel                   |
+    \*-----------------------------------------------------*/
+    for(unsigned int i = 0; i < controller->num_channels; i++)
+    {
+        uint8_t channel_idx = controller->enabled_channels[i];
+        
+        zone new_zone;
+        new_zone.type = ZONE_TYPE_SINGLE;
+        new_zone.leds_min = 1;
+        new_zone.leds_max = 1;
+        new_zone.leds_count = 1;
+        
+        /*-----------------------------------------------------*\
+        | Channel names from SignalRGB                          |
+        \*-----------------------------------------------------*/
+        if(channel_idx == ASROCK_GPU_CHANNEL_ARGB_HEADER)
+        {
+            new_zone.name = "ARGB Header";
+        }
+        else if(channel_idx == ASROCK_GPU_CHANNEL_TOP_SIDE)
+        {
+            new_zone.name = "Top Side";
+        }
+        else if(channel_idx == ASROCK_GPU_CHANNEL_FAN)
+        {
+            new_zone.name = "Fan";
+        }
+        else
+        {
+            new_zone.name = "Channel " + std::to_string(channel_idx);
+        }
+        
+        zones.push_back(new_zone);
+        
+        /*-----------------------------------------------------*\
+        | Set up LED for this zone                              |
+        \*-----------------------------------------------------*/
+        led new_led;
+        new_led.name = new_zone.name;
+        leds.push_back(new_led);
+    }
+
+    SetupColors();
+}
+
+void RGBController_ASRockGPUSMBus::ResizeZone(int /*zone*/, int /*new_size*/)
+{
+    /*-----------------------------------------------------*\
+    | This device does not support resizing zones           |
+    \*-----------------------------------------------------*/
+}
+
+void RGBController_ASRockGPUSMBus::DeviceUpdateLEDs()
+{
+    for(unsigned int i = 0; i < controller->num_channels; i++)
+    {
+        uint8_t channel_idx = controller->enabled_channels[i];
+        RGBColor color = colors[i];
+        
+        controller->SetChannelColor(channel_idx, 
+                                    RGBGetRValue(color),
+                                    RGBGetGValue(color),
+                                    RGBGetBValue(color));
+    }
+}
+
+void RGBController_ASRockGPUSMBus::UpdateZoneLEDs(int zone)
+{
+    uint8_t channel_idx = controller->enabled_channels[zone];
+    RGBColor color = colors[zone];
+    
+    controller->SetChannelColor(channel_idx,
+                                RGBGetRValue(color),
+                                RGBGetGValue(color),
+                                RGBGetBValue(color));
+}
+
+void RGBController_ASRockGPUSMBus::UpdateSingleLED(int led)
+{
+    UpdateZoneLEDs(led);
+}
+
+void RGBController_ASRockGPUSMBus::DeviceUpdateMode()
+{
+    DeviceUpdateLEDs();
+}
@@ -0,0 +1,34 @@
+/*---------------------------------------------------------*\
+| RGBController_ASRockGPUSMBus.h                            |
+|                                                           |
+|   RGBController for ASRock GPU RGB controllers            |
+|                                                           |
+|   Based on SignalRGB ASRock GPU.js plugin                 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#pragma once
+
+#include "RGBController.h"
+#include "ASRockGPUSMBusController.h"
+
+class RGBController_ASRockGPUSMBus : public RGBController
+{
+public:
+    RGBController_ASRockGPUSMBus(ASRockGPUSMBusController* controller_ptr);
+    ~RGBController_ASRockGPUSMBus();
+
+    void        SetupZones();
+    void        ResizeZone(int zone, int new_size);
+
+    void        DeviceUpdateLEDs();
+    void        UpdateZoneLEDs(int zone);
+    void        UpdateSingleLED(int led);
+
+    void        DeviceUpdateMode();
+
+private:
+    ASRockGPUSMBusController* controller;
+};
@@ -36,7 +36,7 @@ ASRockPolychromeV1SMBusController::~ASRockPolychromeV1SMBusController()

 std::string ASRockPolychromeV1SMBusController::GetDeviceLocation()
 {
-    std::string return_string(bus->device_name);
+    std::string return_string(bus->info.device_name);
    char addr[5];
    snprintf(addr, 5, "0x%02X", dev);
    return_string.append(", address ");
@@ -230,6 +230,8 @@ RGBController_ASRockPolychromeV1SMBus::RGBController_ASRockPolychromeV1SMBus(ASR

 RGBController_ASRockPolychromeV1SMBus::~RGBController_ASRockPolychromeV1SMBus()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -296,10 +298,9 @@ void RGBController_ASRockPolychromeV1SMBus::SetupZones()
    SetupColors();
 }

-void RGBController_ASRockPolychromeV1SMBus::DeviceResizeZone(int zone, int new_size)
+void RGBController_ASRockPolychromeV1SMBus::DeviceConfigureZone(int zone_idx)
 {
-    LOG_TRACE("[%s] DeviceResizeZone(%02X, %02X)", name.c_str(), zone, new_size);
-    controller-> SetARGBSize(new_size & 0xFF);
+    controller-> SetARGBSize(zones[zone_idx].leds_count & 0xFF);
    zones[POLYCHROME_V1_ZONE_ADDRESSABLE].leds_count = 1;
 }

@@ -23,7 +23,7 @@ public:

    void        SetupZones();

-    void        DeviceResizeZone(int zone, int new_size);
+    void        DeviceConfigureZone(int zone_idx);

    void        DeviceUpdateLEDs();
    void        DeviceUpdateZoneLEDs(int zone);
@@ -37,7 +37,7 @@ ASRockPolychromeV2SMBusController::~ASRockPolychromeV2SMBusController()

 std::string ASRockPolychromeV2SMBusController::GetDeviceLocation()
 {
-    std::string return_string(bus->device_name);
+    std::string return_string(bus->info.device_name);
    char addr[5];
    snprintf(addr, 5, "0x%02X", dev);
    return_string.append(", address ");
@@ -185,6 +185,8 @@ RGBController_ASRockPolychromeV2SMBus::RGBController_ASRockPolychromeV2SMBus(ASR

 RGBController_ASRockPolychromeV2SMBus::~RGBController_ASRockPolychromeV2SMBus()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -236,7 +238,6 @@ void RGBController_ASRockPolychromeV2SMBus::SetupZones()
        }
    }

-    unsigned int led_count = 0;
    /*---------------------------------------------------------*\
    | Set up LEDs                                               |
    \*---------------------------------------------------------*/
@@ -266,8 +267,6 @@ void RGBController_ASRockPolychromeV2SMBus::SetupZones()
                \*---------------------------------------------------------*/
                leds.push_back(*new_led);

-                led_count++;
-
                if(zone_idx == POLYCHROME_V2_ZONE_ADDRESSABLE)
                {
                    break;
@@ -279,7 +278,7 @@ void RGBController_ASRockPolychromeV2SMBus::SetupZones()
    SetupColors();
 }

-void RGBController_ASRockPolychromeV2SMBus::DeviceResizeZone(int /*zone*/, int /*new_size*/)
+void RGBController_ASRockPolychromeV2SMBus::DeviceConfigureZone(int /*zone_idx*/)
 {
    /*---------------------------------------------------------*\
    | This device does not support resizing zones               |
@@ -23,7 +23,7 @@ public:

    void        SetupZones();

-    void        DeviceResizeZone(int zone, int new_size);
+    void        DeviceConfigureZone(int zone_idx);

    void        DeviceUpdateLEDs();
    void        DeviceUpdateZoneLEDs(int zone);
@@ -85,31 +85,31 @@ uint16_t GetFirmwareVersion(i2c_smbus_interface* bus, uint8_t address)
    }
 }

-DetectedControllers DetectASRockSMBusControllers(std::vector<i2c_smbus_interface*>& busses)
+DetectedControllers DetectASRockSMBusControllers(std::vector<i2c_smbus_interface*>& buses)
 {
    DetectedControllers detected_controllers;

-    for(unsigned int bus = 0; bus < busses.size(); bus++)
+    for(unsigned int bus = 0; bus < buses.size(); bus++)
    {
-        IF_MOBO_SMBUS(busses[bus]->pci_vendor, busses[bus]->pci_device)
+        IF_MOBO_SMBUS(buses[bus]->info.pci_vendor, buses[bus]->info.pci_device)
        {
-            if(busses[bus]->pci_subsystem_vendor == ASROCK_SUB_VEN)
+            if(buses[bus]->info.pci_subsystem_vendor == ASROCK_SUB_VEN)
            {
                LOG_DEBUG(SMBUS_CHECK_DEVICE_MESSAGE_EN, ASROCK_DETECTOR_NAME, bus, VENDOR_NAME, SMBUS_ADDRESS);
                // Check for Polychrome controller at 0x6A
-                if(TestForPolychromeSMBusController(busses[bus], SMBUS_ADDRESS))
+                if(TestForPolychromeSMBusController(buses[bus], SMBUS_ADDRESS))
                {
                    LOG_DEBUG("[%s] Detected a device at address 0x%02X, testing for a known controller",  ASROCK_DETECTOR_NAME, SMBUS_ADDRESS);

                    u16_to_u8 version;
-                    version.u16 = GetFirmwareVersion(busses[bus], SMBUS_ADDRESS);
+                    version.u16 = GetFirmwareVersion(buses[bus], SMBUS_ADDRESS);

                    switch(version.msb)
                    {
                        case ASROCK_TYPE_ASRLED:
                            {
                                LOG_DEBUG("[%s] Found a ASR RGB LED Controller", ASROCK_DETECTOR_NAME);
-                                ASRockASRRGBSMBusController* controller = new ASRockASRRGBSMBusController(busses[bus], SMBUS_ADDRESS);
+                                ASRockASRRGBSMBusController* controller = new ASRockASRRGBSMBusController(buses[bus], SMBUS_ADDRESS);
                                controller-> fw_version = version.u16;
                                RGBController_ASRockASRRGBSMBus* rgb_controller = new RGBController_ASRockASRRGBSMBus(controller);
                                detected_controllers.push_back(rgb_controller);
@@ -119,7 +119,7 @@ DetectedControllers DetectASRockSMBusControllers(std::vector<i2c_smbus_interface
                            case ASROCK_TYPE_POLYCHROME_V1:
                            {
                                LOG_DEBUG("[%s] Found a Polychrome v1 Controller", ASROCK_DETECTOR_NAME);
-                                ASRockPolychromeV1SMBusController* controller = new ASRockPolychromeV1SMBusController(busses[bus], SMBUS_ADDRESS);
+                                ASRockPolychromeV1SMBusController* controller = new ASRockPolychromeV1SMBusController(buses[bus], SMBUS_ADDRESS);
                                controller-> fw_version = version.u16;
                                RGBController_ASRockPolychromeV1SMBus* rgb_controller = new RGBController_ASRockPolychromeV1SMBus(controller);
                                detected_controllers.push_back(rgb_controller);
@@ -129,7 +129,7 @@ DetectedControllers DetectASRockSMBusControllers(std::vector<i2c_smbus_interface
                            case ASROCK_TYPE_POLYCHROME_V2:
                            {
                                LOG_DEBUG("[%s] Found a Polychrome v2 Controller", ASROCK_DETECTOR_NAME);
-                                ASRockPolychromeV2SMBusController* controller = new ASRockPolychromeV2SMBusController(busses[bus], SMBUS_ADDRESS);
+                                ASRockPolychromeV2SMBusController* controller = new ASRockPolychromeV2SMBusController(buses[bus], SMBUS_ADDRESS);
                                controller-> fw_version = version.u16;
                                RGBController_ASRockPolychromeV2SMBus* rgb_controller = new RGBController_ASRockPolychromeV2SMBus(controller);
                                detected_controllers.push_back(rgb_controller);
@@ -0,0 +1,50 @@
+/*---------------------------------------------------------*\
+| RGBController_AcerNitroHidKeyboard.cpp                    |
+|                                                           |
+|   Detector for Acer Nitro HID Keyboard                    |
+|                                                           |
+|   Marek Pokropiński                           Jul 27 2026 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include <vector>
+#include "DetectionManager.h"
+#include "AcerNitroHidKeyboardController.h"
+#include "RGBController_AcerNitroHidKeyboard.h"
+#include "RGBController_AcerNitroHidLed.h"
+
+/*---------------------------------------------------------*\
+| HID vendor and product IDs for ENEK EC in Acer Nitro      |
+\*---------------------------------------------------------*/
+
+#define ACER_ENEC_VID           0x0CF2
+#define ACER_ENEC_PID           0x5130
+#define ACER_ENEC_USAGE_PAGE    0xFF5A
+#define ACER_ENEC_USAGE         0x01
+
+DetectedControllers DetectAcerHIDControllers(hid_device_info* info, const std::string&)
+{
+    DetectedControllers detected_controllers;
+    hid_device*         dev;
+
+    dev = hid_open_path(info->path);
+    if(dev)
+    {
+        /*-------------------------------------------------*\
+        | Controller is shared between keyboard and onboard |
+        | led                                               |
+        \*-------------------------------------------------*/
+        std::shared_ptr<AcerNitroHidKeyboardController> controller  = std::make_shared<AcerNitroHidKeyboardController>(dev, info->path);
+        RGBController_AcerNitroHidKeyboard* rgb_kb_controller       = new RGBController_AcerNitroHidKeyboard(controller);
+        RGBController_AcerNitroHidLed* rgb_led_controller           = new RGBController_AcerNitroHidLed(controller);
+
+        detected_controllers.push_back(rgb_kb_controller);
+        detected_controllers.push_back(rgb_led_controller);
+    }
+
+    return(detected_controllers);
+}
+
+REGISTER_HID_DETECTOR_PU("AcerNitroHidKeyboardController", DetectAcerHIDControllers, ACER_ENEC_VID, ACER_ENEC_PID, ACER_ENEC_USAGE_PAGE, ACER_ENEC_USAGE);
@@ -0,0 +1,80 @@
+/*---------------------------------------------------------*\
+| RGBController_AcerNitroHidKeyboard.cpp                    |
+|                                                           |
+|   Driver for Acer Nitro Keyboard                          |
+|                                                           |
+|   Marek Pokropiński                           Jul 27 2026 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include "AcerNitroHidKeyboardController.h"
+
+AcerNitroHidKeyboardController::AcerNitroHidKeyboardController(hid_device *dev_handle, const char *path)
+{
+    this->location  = path;
+    this->dev       = dev_handle;
+
+    device_name     = "Acer Nitro HID Keyboard";    
+}
+
+AcerNitroHidKeyboardController::~AcerNitroHidKeyboardController()
+{
+    if(dev)
+    {
+        hid_close(dev);
+    }
+}
+
+std::string AcerNitroHidKeyboardController::GetLocation() const
+{
+    return("HID: " + location);
+}
+
+std::string AcerNitroHidKeyboardController::GetDeviceName() const
+{
+    return(device_name);
+}
+
+void AcerNitroHidKeyboardController::SetLEDs(const std::vector<RGBColor>& colors, unsigned char brightness, unsigned char device_id)
+{
+    std::lock_guard<std::mutex> guard(device_mutex);
+
+    for(unsigned int led_idx = 0; (led_idx < colors.size()) && (led_idx < ACER_HID_NUM_ZONES); led_idx++)
+    {
+        /*-------------------------------------------------*\
+        | Convert colors to RGB format                      |
+        \*-------------------------------------------------*/
+        unsigned char r = RGBGetRValue(colors[led_idx]);
+        unsigned char g = RGBGetGValue(colors[led_idx]);        
+        unsigned char b = RGBGetBValue(colors[led_idx]);
+
+        /*-------------------------------------------------*\
+        | Send packet                                       |
+        \*-------------------------------------------------*/
+        unsigned char zone_select                   = (unsigned char)(1<<led_idx);
+        unsigned char packet[ACER_HID_PACKET_SIZE]  = {0xA4, device_id, ACER_HID_MODE_STATIC, brightness, 0, 1, r, g, b, zone_select, 0};
+        hid_send_feature_report(dev, packet, ACER_HID_PACKET_SIZE);
+    }
+}
+
+void AcerNitroHidKeyboardController::SetAllLEDs(const RGBColor &color, unsigned char brightness, unsigned char speed, unsigned char direction, unsigned char mode, unsigned char device_id)
+{
+    std::lock_guard<std::mutex> guard(device_mutex);
+
+    /*-----------------------------------------------------*\
+    | Convert color to RGB format                           |
+    \*-----------------------------------------------------*/
+    unsigned char r = RGBGetRValue(color);
+    unsigned char g = RGBGetGValue(color);        
+    unsigned char b = RGBGetBValue(color);
+
+    /*-----------------------------------------------------*\
+    | Send packet                                           |
+    | Zone select = All zones                               |
+    \*-----------------------------------------------------*/
+    unsigned char zone_select                   = 0x0F;
+    unsigned char packet[ACER_HID_PACKET_SIZE]  = {0xA4, device_id, mode, brightness, speed, direction, r, g, b, zone_select, 0};
+    hid_send_feature_report(dev, packet, ACER_HID_PACKET_SIZE);
+}
@@ -0,0 +1,56 @@
+/*---------------------------------------------------------*\
+| RGBController_AcerNitroHidKeyboard.cpp                    |
+|                                                           |
+|   Driver for Acer Nitro Keyboard                          |
+|                                                           |
+|   Marek Pokropiński                           Jul 27 2026 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#pragma once
+
+enum
+{
+    ACER_HID_MODE_DIRECT    = 1,
+    ACER_HID_MODE_STATIC    = 2,
+    ACER_HID_MODE_BREATHING = 4,
+    ACER_HID_MODE_NEON      = 5,
+    ACER_HID_MODE_OPMODE    = 6,
+    ACER_HID_MODE_WAVE      = 7,
+    ACER_HID_MODE_SHIFTING  = 8,
+    ACER_HID_MODE_ZOOM      = 9,
+    ACER_HID_MODE_METEOR    = 10,
+    ACER_HID_MODE_TWINKLING = 11,
+};
+
+#define ACER_HID_NAME_BUFFER_SIZE 255
+#define ACER_HID_NUM_ZONES 4
+#define ACER_HID_PACKET_SIZE 11
+
+#include <mutex>
+#include <string>
+#include <vector>
+#include <hidapi.h>
+#include "RGBControllerInterface.h"
+
+class AcerNitroHidKeyboardController
+{
+public:
+    AcerNitroHidKeyboardController(hid_device *dev_handle, const char *path);
+    ~AcerNitroHidKeyboardController();
+
+    std::string GetDeviceName() const;
+    std::string GetSerial() const;
+    std::string GetLocation() const;
+
+    void SetLEDs(const std::vector<RGBColor> &colors, unsigned char brightness, unsigned char device_id);
+    void SetAllLEDs(const RGBColor &color, unsigned char brightness, unsigned char speed, unsigned char direction, unsigned char mode, unsigned char device_id);
+
+private:
+    hid_device *dev;
+    std::string device_name;
+    std::string location;
+    std::mutex device_mutex;
+};
@@ -0,0 +1,231 @@
+/*---------------------------------------------------------*\
+| RGBController_AcerNitroHidKeyboard.cpp                    |
+|                                                           |
+|   RGBController for Acer Nitro HID Keyboard               |
+|                                                           |
+|   Marek Pokropiński                           Jul 27 2026 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include "RGBController_AcerNitroHidKeyboard.h"
+
+/**------------------------------------------------------------------*\
+    @name Acer Nitro HID Keyboard
+    @category Laptop
+    @type HID
+    @save :x:
+    @direct :white_check_mark:
+    @effects :white_check_mark:
+    @detectors DetectAcerHIDControllers
+    @comment
+\*-------------------------------------------------------------------*/
+
+RGBController_AcerNitroHidKeyboard::RGBController_AcerNitroHidKeyboard(std::shared_ptr<AcerNitroHidKeyboardController> controller)
+{
+    this->controller            = controller;
+    device_id                   = 0x21;
+
+    name                        = "Acer Nitro HID Keyboard";
+    vendor                      = "Acer";
+    type                        = DEVICE_TYPE_LAPTOP;
+    description                 = "Acer Nitro HID Keyboard Device";
+    location                    = controller->GetLocation();
+
+    mode Direct;
+    Direct.name                 = "Direct";
+    Direct.value                = ACER_HID_MODE_DIRECT;
+    Direct.flags                = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS ;
+    Direct.color_mode           = MODE_COLORS_PER_LED;
+    Direct.brightness_min       = 0;
+    Direct.brightness_max       = 100;
+    Direct.brightness           = 100;
+
+    modes.push_back(Direct);
+
+    mode Static;
+    Static.name                 = "Static";
+    Static.value                = ACER_HID_MODE_STATIC;
+    Static.flags                = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR  | MODE_FLAG_HAS_BRIGHTNESS;
+    Static.color_mode           = MODE_COLORS_MODE_SPECIFIC;
+    Static.brightness_min       = 0;
+    Static.brightness_max       = 100;
+    Static.brightness           = 100;
+    Static.colors_min           = 1;
+    Static.colors_max           = 1;
+    Static.colors.resize(1);
+    Static.speed                = 0;
+
+    modes.push_back(Static);
+
+    mode Breathing;
+    Breathing.name              = "Breathing";
+    Breathing.value             = ACER_HID_MODE_BREATHING;
+    Breathing.flags             = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR  | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Breathing.color_mode        = MODE_COLORS_MODE_SPECIFIC;
+    Breathing.brightness_min    = 0;
+    Breathing.brightness_max    = 100;
+    Breathing.brightness        = 100;
+    Breathing.colors_min        = 1;
+    Breathing.colors_max        = 1;
+    Breathing.speed_min         = 1;
+    Breathing.speed_max         = 9;
+    Breathing.speed             = 4;
+    Breathing.colors.resize(1);
+
+    modes.push_back(Breathing);
+
+    mode Neon;
+    Neon.name                   = "Neon";
+    Neon.value                  = ACER_HID_MODE_NEON;
+    Neon.flags                  = MODE_FLAG_REQUIRES_ENTIRE_DEVICE | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Neon.color_mode             = MODE_COLORS_NONE;
+    Neon.brightness_min         = 0;
+    Neon.brightness_max         = 100;
+    Neon.brightness             = 100;
+    Neon.speed_min              = 1;
+    Neon.speed_max              = 9;
+    Neon.speed                  = 4;
+
+    modes.push_back(Neon);
+
+    mode Wave;
+    Wave.name                   = "Wave";
+    Wave.value                  = ACER_HID_MODE_WAVE;
+    Wave.flags                  = MODE_FLAG_REQUIRES_ENTIRE_DEVICE | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED | MODE_FLAG_HAS_DIRECTION_LR;
+    Wave.color_mode             = MODE_COLORS_NONE;
+    Wave.brightness_min         = 0;
+    Wave.brightness_max         = 100;
+    Wave.brightness             = 100;
+    Wave.speed_min              = 1;
+    Wave.speed_max              = 9;
+    Wave.speed                  = 4;
+    Wave.direction              = 0;
+
+    modes.push_back(Wave);
+
+    mode Shifting;
+    Shifting.name               = "Shifting";
+    Shifting.value              = ACER_HID_MODE_SHIFTING;
+    Shifting.flags              = MODE_FLAG_REQUIRES_ENTIRE_DEVICE | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Shifting.color_mode         = MODE_COLORS_NONE;
+    Shifting.brightness_min     = 0;
+    Shifting.brightness_max     = 100;
+    Shifting.brightness         = 100;
+    Shifting.speed_min          = 1;
+    Shifting.speed_max          = 9;
+    Shifting.speed              = 4;
+
+    modes.push_back(Shifting);
+
+    mode Zoom;
+    Zoom.name                   = "Zoom";
+    Zoom.value                  = ACER_HID_MODE_ZOOM;
+    Zoom.flags                  = MODE_FLAG_REQUIRES_ENTIRE_DEVICE | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Zoom.color_mode             = MODE_COLORS_NONE;
+    Zoom.brightness_min         = 0;
+    Zoom.brightness_max         = 100;
+    Zoom.brightness             = 100;
+    Zoom.speed_min              = 1;
+    Zoom.speed_max              = 9;
+    Zoom.speed                  = 4;
+
+    modes.push_back(Zoom);
+
+    mode Meteor;
+    Meteor.name                 = "Meteor";
+    Meteor.value                = ACER_HID_MODE_METEOR;
+    Meteor.flags                = MODE_FLAG_REQUIRES_ENTIRE_DEVICE | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Meteor.color_mode           = MODE_COLORS_NONE;
+    Meteor.brightness_min       = 0;
+    Meteor.brightness_max       = 100;
+    Meteor.brightness           = 100;
+    Meteor.speed_min            = 1;
+    Meteor.speed_max            = 9;
+    Meteor.speed                = 4;
+
+    modes.push_back(Meteor);
+
+    mode Twinkling;
+    Twinkling.name              = "Twinkling";
+    Twinkling.value             = ACER_HID_MODE_TWINKLING;
+    Twinkling.flags             = MODE_FLAG_REQUIRES_ENTIRE_DEVICE | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Twinkling.color_mode        = MODE_COLORS_NONE;
+    Twinkling.brightness_min    = 0;
+    Twinkling.brightness_max    = 100;
+    Twinkling.brightness        = 100;
+    Twinkling.colors_min        = 1;
+    Twinkling.colors_max        = 1;
+    Twinkling.speed_min         = 1;
+    Twinkling.speed_max         = 9;
+    Twinkling.speed             = 4;
+
+    modes.push_back(Twinkling);
+
+    SetupZones();
+}
+
+RGBController_AcerNitroHidKeyboard::~RGBController_AcerNitroHidKeyboard()
+{
+    Shutdown();
+}
+
+void RGBController_AcerNitroHidKeyboard::SetupZones()
+{
+    zone* new_zone          = new zone;
+
+    new_zone->name          = "Keyboard Backlight Zone";
+    new_zone->type          = ZONE_TYPE_LINEAR;
+    new_zone->leds_min      = 4;
+    new_zone->leds_max      = 4;
+    new_zone->leds_count    = 4;
+
+    zones.push_back(*new_zone);
+
+    for(std::size_t zone_idx = 0; zone_idx < ACER_HID_NUM_ZONES; zone_idx++)
+    {
+        led* new_led        = new led();
+        new_led->name       = "Keyboard Backlight Zone ";
+        new_led->name.append(std::to_string(zone_idx + 1));
+        new_led->value      = (unsigned int)leds.size();
+
+        leds.push_back(*new_led);
+    }
+
+    SetupColors();
+}
+
+void RGBController_AcerNitroHidKeyboard::DeviceUpdateLEDs()
+{
+    mode& current_mode = modes[active_mode];
+    if(current_mode.value == ACER_HID_MODE_DIRECT)
+    {
+        controller->SetLEDs(colors, current_mode.brightness, device_id);
+    }
+    else
+    {
+        RGBColor color          = current_mode.colors.size()==0? (RGBColor)0 :  current_mode.colors[0];
+        unsigned char direction = 1;
+        if((modes[active_mode].flags & MODE_FLAG_HAS_DIRECTION_LR) && modes[active_mode].direction)
+        {
+            direction           = 2;
+        }
+        controller->SetAllLEDs(color, current_mode.brightness, current_mode.speed, direction, current_mode.value, device_id);
+    }
+}
+
+void RGBController_AcerNitroHidKeyboard::DeviceUpdateZoneLEDs(int)
+{
+    DeviceUpdateLEDs();
+}
+
+void RGBController_AcerNitroHidKeyboard::DeviceUpdateSingleLED(int)
+{
+    DeviceUpdateLEDs();
+}
+
+void RGBController_AcerNitroHidKeyboard::DeviceUpdateMode()
+{
+    DeviceUpdateLEDs();
+}
@@ -0,0 +1,33 @@
+/*---------------------------------------------------------*\
+| RGBController_AcerNitroHidKeyboard.cpp                    |
+|                                                           |
+|   RGBController for Acer Nitro HID Keyboard               |
+|                                                           |
+|   Marek Pokropiński                           Jul 27 2026 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#pragma once
+
+#include "RGBController.h"
+#include "AcerNitroHidKeyboardController.h"
+
+class RGBController_AcerNitroHidKeyboard : public RGBController
+{
+public:
+    RGBController_AcerNitroHidKeyboard(std::shared_ptr<AcerNitroHidKeyboardController> controller);
+    ~RGBController_AcerNitroHidKeyboard();
+
+    void SetupZones();
+
+    void DeviceUpdateLEDs();
+    void DeviceUpdateZoneLEDs(int zone);
+    void DeviceUpdateSingleLED(int led);
+    void DeviceUpdateMode();
+
+private:
+    std::shared_ptr<AcerNitroHidKeyboardController> controller;
+    unsigned int device_id;
+};
@@ -0,0 +1,152 @@
+/*---------------------------------------------------------*\
+| RGBController_AcerNitroHidLed.cpp                         |
+|                                                           |
+|   RGBController for Acer Nitro HID LED                    |
+|                                                           |
+|   Marek Pokropiński                           Jul 27 2026 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include "RGBController_AcerNitroHidLed.h"
+
+/**------------------------------------------------------------------*\
+    @name Acer Nitro HID Led
+    @category Laptop
+    @type HID
+    @save :x:
+    @direct :white_check_mark:
+    @effects :white_check_mark:
+    @detectors DetectAcerHIDControllers
+    @comment
+\*-------------------------------------------------------------------*/
+
+RGBController_AcerNitroHidLed::RGBController_AcerNitroHidLed(std::shared_ptr<AcerNitroHidKeyboardController> controller)
+{
+    this->controller            = controller;
+    device_id                   = 0x65;
+
+    name                        = "Acer Nitro HID LED Device";
+    vendor                      = "Acer";
+    type                        = DEVICE_TYPE_LIGHT;
+    description                 = "Acer Nitro HID LED Device";
+    location                    = controller->GetLocation();
+
+    mode Direct;
+    Direct.name                 = "Direct";
+    Direct.value                = ACER_HID_MODE_DIRECT;
+    Direct.flags                = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS ;
+    Direct.color_mode           = MODE_COLORS_PER_LED;
+    Direct.brightness_min       = 0;
+    Direct.brightness_max       = 100;
+    Direct.brightness           = 100;
+
+    modes.push_back(Direct);
+
+    mode Static;
+    Static.name                 = "Static";
+    Static.value                = ACER_HID_MODE_STATIC;
+    Static.flags                = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR  | MODE_FLAG_HAS_BRIGHTNESS;
+    Static.color_mode           = MODE_COLORS_MODE_SPECIFIC;
+    Static.brightness_min       = 0;
+    Static.brightness_max       = 100;
+    Static.brightness           = 100;
+    Static.colors_min           = 1;
+    Static.colors_max           = 1;
+    Static.colors.resize(1);
+    Static.speed                = 0;
+
+    modes.push_back(Static);
+
+    mode Breathing;
+    Breathing.name              = "Breathing";
+    Breathing.value             = ACER_HID_MODE_BREATHING;
+    Breathing.flags             = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR  | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Breathing.color_mode        = MODE_COLORS_MODE_SPECIFIC;
+    Breathing.brightness_min    = 0;
+    Breathing.brightness_max    = 100;
+    Breathing.brightness        = 100;
+    Breathing.colors_min        = 1;
+    Breathing.colors_max        = 1;
+    Breathing.speed_min         = 1;
+    Breathing.speed_max         = 5;
+    Breathing.speed             = 4;
+    Breathing.colors.resize(1);
+
+    modes.push_back(Breathing);
+
+    mode Neon;
+    Neon.name                   = "Neon";
+    Neon.value                  = ACER_HID_MODE_NEON;
+    Neon.flags                  = MODE_FLAG_REQUIRES_ENTIRE_DEVICE | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Neon.color_mode             = MODE_COLORS_NONE;
+    Neon.brightness_min         = 0;
+    Neon.brightness_max         = 100;
+    Neon.brightness             = 100;
+    Neon.speed_min              = 1;
+    Neon.speed_max              = 5;
+    Neon.speed                  = 4;
+
+    modes.push_back(Neon);
+
+    SetupZones();
+}
+
+RGBController_AcerNitroHidLed::~RGBController_AcerNitroHidLed()
+{
+    Shutdown();
+}
+
+void RGBController_AcerNitroHidLed::SetupZones()
+{
+    zone* new_zone          = new zone;
+
+    new_zone->name          = "LED";
+    new_zone->type          = ZONE_TYPE_LINEAR;
+    new_zone->leds_min      = 1;
+    new_zone->leds_max      = 1;
+    new_zone->leds_count    = 1;
+    zones.push_back(*new_zone);
+
+    led* new_led            = new led();
+    new_led->name           = "LED";
+    new_led->value          = (unsigned int)leds.size();
+    leds.push_back(*new_led);
+
+    SetupColors();
+}
+
+void RGBController_AcerNitroHidLed::DeviceUpdateLEDs()
+{
+    mode& current_mode = modes[active_mode];
+    if(current_mode.value == ACER_HID_MODE_DIRECT)
+    {
+        controller->SetLEDs(colors, current_mode.brightness, device_id);
+    }
+    else
+    {
+        RGBColor color          = current_mode.colors.size()==0? (RGBColor)0 :  current_mode.colors[0];
+        unsigned char direction = 1;
+        if((modes[active_mode].flags & MODE_FLAG_HAS_DIRECTION_LR) && modes[active_mode].direction)
+        {
+            direction           = 2;
+        }
+        controller->SetAllLEDs(color, current_mode.brightness, current_mode.speed, direction, current_mode.value, device_id);
+    }
+}
+
+void RGBController_AcerNitroHidLed::DeviceUpdateZoneLEDs(int)
+{
+    DeviceUpdateLEDs();
+}
+
+void RGBController_AcerNitroHidLed::DeviceUpdateSingleLED(int)
+{
+    DeviceUpdateLEDs();
+}
+
+void RGBController_AcerNitroHidLed::DeviceUpdateMode()
+{
+    DeviceUpdateLEDs();
+}
@@ -0,0 +1,35 @@
+/*---------------------------------------------------------*\
+| RGBController_AcerNitroHidLed.cpp                         |
+|                                                           |
+|   RGBController for Acer Nitro HID LED                    |
+|                                                           |
+|   Marek Pokropiński                           Jul 27 2026 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#pragma once
+
+#include "RGBController.h"
+#include "AcerNitroHidKeyboardController.h"
+#include "RGBController_AcerNitroHidKeyboard.h"
+
+class RGBController_AcerNitroHidLed : public RGBController
+{
+public:
+    RGBController_AcerNitroHidLed(std::shared_ptr<AcerNitroHidKeyboardController> controller);
+    ~RGBController_AcerNitroHidLed();
+
+    void SetupZones();
+
+    void DeviceUpdateLEDs();
+    void DeviceUpdateZoneLEDs(int zone);
+    void DeviceUpdateSingleLED(int led);
+
+    void DeviceUpdateMode();
+
+private:
+    std::shared_ptr<AcerNitroHidKeyboardController> controller;
+    unsigned int device_id;
+};
@@ -32,6 +32,7 @@ static const std::map<alienware_platform_id, uint8_t> zone_quirks_table =
    { 0x0C01,   4 },    // Dell G5 SE 5505
    { 0x0A01,  16 },    // Dell G7 15 7500
    { 0x0E03,   4 },    // Dell G15   5511
+    { 0x0E07,   4 },    // Dell G15   5520
    { 0x0E0A,   4 }     // Dell G15   5530

 };
@@ -49,9 +50,21 @@ static const std::map<alienware_platform_id, std::vector<const char*>> zone_name
                  "Light Bar 7",    "Light Bar 8",  "Light Bar 9",
                  "Light Bar 10",   "Light Bar 11", "Light Bar 12"              } },
    { 0x0E03,   { "Left",           "Middle",       "Right",        "Numpad"    } },
+    { 0x0E07,   { "Left",           "Middle",       "Right",        "Numpad"    } },
    { 0x0E0A,   { "Left",           "Middle",       "Right",        "Numpad"    } }
 };

+/*---------------------------------------------------------*\
+| Mapping the platform ID to the actual hardware zone IDs   |
+\*---------------------------------------------------------*/
+static const std::map<alienware_platform_id, std::vector<uint8_t>> zone_ids_table =
+{
+    { 0x0C01,   { 0x00, 0x01, 0x02, 0x03 } }, // Dell G5 SE 5505
+    { 0x0E03,   { 0x00, 0x01, 0x02, 0x03 } }, // Dell G15   5511
+    { 0x0E07,   { 0x10, 0x11, 0x12, 0x13 } }, // Dell G15   5520
+    { 0x0E0A,   { 0x10, 0x11, 0x12, 0x13 } }  // Dell G15   5530
+};
+
 static void SendHIDReport(hid_device *dev, const unsigned char* usb_buf, size_t usb_buf_size)
 {
    using namespace std::chrono_literals;
@@ -138,6 +151,21 @@ AlienwareController::AlienwareController(hid_device* dev_handle, const hid_devic
        }
    }

+    /*-----------------------------------------------------*\
+    | Initialize hardware zone IDs                          |
+    \*-----------------------------------------------------*/
+    if(zone_ids_table.count(platform_id))
+    {
+        zone_ids = zone_ids_table.at(platform_id);
+    }
+    else
+    {
+        for(size_t i = 0; i < number_of_zones; i++)
+        {
+            zone_ids.push_back(static_cast<uint8_t>(i));
+        }
+    }
+
    /*-----------------------------------------------------*\
    | Set defaults for all zones                            |
    | It doesn't seem possible to read the controller's     |
@@ -155,6 +183,7 @@ AlienwareController::AlienwareController(hid_device* dev_handle, const hid_devic
        zones[zone_idx].period      = 2000;
        zones[zone_idx].tempo       = ALIENWARE_TEMPO_MAX;
        zones[zone_idx].dim         = 0;
+        zones[zone_idx].direction   = 0;
    }

    /*-----------------------------------------------------*\
@@ -266,42 +295,53 @@ bool AlienwareController::Dim(std::vector<uint8_t> zones, double percent)
        return(true);
    }

-    unsigned char usb_buf[HIDAPI_ALIENWARE_REPORT_SIZE];
+    bool result = true;

    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
+    | Split the zone list into packet-sized chunks so it    |
+    | never overflows usb_buf                               |
    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up message packet with leading 00, per hidapi     |
-    \*-----------------------------------------------------*/
-    uint16_t num_zones  = (uint16_t)zones.size();
-
-    usb_buf[0x00]       = 0x00;
-    usb_buf[0x01]       = 0x03;
-    usb_buf[0x02]       = ALIENWARE_COMMAND_DIM;
-    usb_buf[0x03]       = static_cast<uint8_t>(percent);
-    usb_buf[0x04]       = num_zones >> 8;
-    usb_buf[0x05]       = num_zones & 0xFF;
-
-    for(size_t i = 0; i < num_zones; i++)
+    for(size_t offset = 0; offset < zones.size(); offset += ALIENWARE_MAX_ZONES_PER_PACKET)
    {
-        usb_buf[0x06+i] = zones[i];
+        unsigned char usb_buf[HIDAPI_ALIENWARE_REPORT_SIZE];
+
+        /*-------------------------------------------------*\
+        | Zero out buffer                                   |
+        \*-------------------------------------------------*/
+        memset(usb_buf, 0x00, sizeof(usb_buf));
+
+        /*-------------------------------------------------*\
+        | Set up message packet with leading 00, per hidapi |
+        \*-------------------------------------------------*/
+        uint16_t num_zones  = (uint16_t)std::min<size_t>(ALIENWARE_MAX_ZONES_PER_PACKET, zones.size() - offset);
+
+        usb_buf[0x00]       = 0x00;
+        usb_buf[0x01]       = 0x03;
+        usb_buf[0x02]       = ALIENWARE_COMMAND_DIM;
+        usb_buf[0x03]       = static_cast<uint8_t>(percent);
+        usb_buf[0x04]       = num_zones >> 8;
+        usb_buf[0x05]       = num_zones & 0xFF;
+
+        for(size_t i = 0; i < num_zones; i++)
+        {
+            usb_buf[0x06+i] = zones[offset + i];
+        }
+
+        /*-------------------------------------------------*\
+        | Send packet                                       |
+        \*-------------------------------------------------*/
+        SendHIDReport(dev, usb_buf, sizeof(usb_buf));
+
+        HidapiAlienwareReport response = GetResponse();
+
+        /*-------------------------------------------------*\
+        | For this command, error is if the output equals   |
+        | the input                                         |
+        \*-------------------------------------------------*/
+        result &= (response.data[1] == 0x03) && memcmp(usb_buf, response.data, HIDAPI_ALIENWARE_REPORT_SIZE);
    }

-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    SendHIDReport(dev, usb_buf, sizeof(usb_buf));
-
-    HidapiAlienwareReport response = GetResponse();
-
-    /*-----------------------------------------------------*\
-    | For this command, error is if the output equals the   |
-    | input                                                 |
-    \*-----------------------------------------------------*/
-    return((response.data[1] == 0x03) && memcmp(usb_buf, response.data, HIDAPI_ALIENWARE_REPORT_SIZE));
+    return(result);
 }

 bool AlienwareController::UserAnimation(uint16_t subcommand, uint16_t animation, uint16_t duration)
@@ -370,42 +410,53 @@ bool AlienwareController::SelectZones(const std::vector<uint8_t>& zones)
        return(false);
    }

-    unsigned char usb_buf[HIDAPI_ALIENWARE_REPORT_SIZE];
+    bool result = true;

    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
+    | Split the zone list into packet-sized chunks so it    |
+    | never overflows usb_buf                               |
    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up message packet with leading 00, per hidapi     |
-    \*-----------------------------------------------------*/
-    uint16_t num_zones  = (uint16_t)zones.size();
-
-    usb_buf[0x00]       = 0x00;
-    usb_buf[0x01]       = 0x03;
-    usb_buf[0x02]       = ALIENWARE_COMMAND_SELECT_ZONES;
-    usb_buf[0x03]       = 1; // loop?
-    usb_buf[0x04]       = num_zones >> 8;
-    usb_buf[0x05]       = num_zones & 0xFF;
-
-    for(size_t i = 0; i < num_zones; i++)
+    for(size_t offset = 0; offset < zones.size(); offset += ALIENWARE_MAX_ZONES_PER_PACKET)
    {
-        usb_buf[0x06+i] = zones[i];
+        unsigned char usb_buf[HIDAPI_ALIENWARE_REPORT_SIZE];
+
+        /*-------------------------------------------------*\
+        | Zero out buffer                                   |
+        \*-------------------------------------------------*/
+        memset(usb_buf, 0x00, sizeof(usb_buf));
+
+        /*-------------------------------------------------*\
+        | Set up message packet with leading 00, per hidapi |
+        \*-------------------------------------------------*/
+        uint16_t num_zones  = (uint16_t)std::min<size_t>(ALIENWARE_MAX_ZONES_PER_PACKET, zones.size() - offset);
+
+        usb_buf[0x00]       = 0x00;
+        usb_buf[0x01]       = 0x03;
+        usb_buf[0x02]       = ALIENWARE_COMMAND_SELECT_ZONES;
+        usb_buf[0x03]       = 1; // loop?
+        usb_buf[0x04]       = num_zones >> 8;
+        usb_buf[0x05]       = num_zones & 0xFF;
+
+        for(size_t i = 0; i < num_zones; i++)
+        {
+            usb_buf[0x06+i] = zones[offset + i];
+        }
+
+        /*-------------------------------------------------*\
+        | Send packet                                       |
+        \*-------------------------------------------------*/
+        SendHIDReport(dev, usb_buf, sizeof(usb_buf));
+
+        HidapiAlienwareReport response = GetResponse();
+
+        /*-------------------------------------------------*\
+        | For this command, error is if the output equals   |
+        | the input                                         |
+        \*-------------------------------------------------*/
+        result &= (response.data[1] == 0x03) && memcmp(usb_buf, response.data, HIDAPI_ALIENWARE_REPORT_SIZE);
    }

-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    SendHIDReport(dev, usb_buf, sizeof(usb_buf));
-
-    HidapiAlienwareReport response = GetResponse();
-
-    /*-----------------------------------------------------*\
-    | For this command, error is if the output equals the   |
-    | input                                                 |
-    \*-----------------------------------------------------*/
-    return((response.data[1] == 0x03) && memcmp(usb_buf, response.data, HIDAPI_ALIENWARE_REPORT_SIZE));
+    return(result);
 }

 bool AlienwareController::ModeAction(uint8_t mode, uint16_t duration, uint16_t tempo, RGBColor color)
@@ -509,44 +560,55 @@ bool AlienwareController::SetColorDirect(RGBColor color, std::vector<uint8_t> zo
        return(true);
    }

-    unsigned char usb_buf[HIDAPI_ALIENWARE_REPORT_SIZE];
+    bool result = true;

    /*-----------------------------------------------------*\
-    | Zero out buffer                                       |
+    | Split the zone list into packet-sized chunks so it    |
+    | never overflows usb_buf                               |
    \*-----------------------------------------------------*/
-    memset(usb_buf, 0x00, sizeof(usb_buf));
-
-    /*-----------------------------------------------------*\
-    | Set up message packet with leading 00, per hidapi     |
-    \*-----------------------------------------------------*/
-    uint16_t num_zones      = (uint16_t)zones.size();
-
-    usb_buf[0x00]           = 0x00;
-    usb_buf[0x01]           = 0x03;
-    usb_buf[0x02]           = ALIENWARE_COMMAND_SET_COLOR;
-    usb_buf[0x03]           = RGBGetRValue(color);
-    usb_buf[0x04]           = RGBGetGValue(color);
-    usb_buf[0x05]           = RGBGetBValue(color);
-    usb_buf[0x06]           = num_zones >> 8;
-    usb_buf[0x07]           = num_zones & 0xFF;
-
-    for(size_t i = 0; i < num_zones; i++)
+    for(size_t offset = 0; offset < zones.size(); offset += ALIENWARE_MAX_ZONES_PER_PACKET)
    {
-        usb_buf[0x08 + i]   = zones[i];
+        unsigned char usb_buf[HIDAPI_ALIENWARE_REPORT_SIZE];
+
+        /*-------------------------------------------------*\
+        | Zero out buffer                                   |
+        \*-------------------------------------------------*/
+        memset(usb_buf, 0x00, sizeof(usb_buf));
+
+        /*-------------------------------------------------*\
+        | Set up message packet with leading 00, per hidapi |
+        \*-------------------------------------------------*/
+        uint16_t num_zones      = (uint16_t)std::min<size_t>(ALIENWARE_MAX_ZONES_PER_PACKET, zones.size() - offset);
+
+        usb_buf[0x00]           = 0x00;
+        usb_buf[0x01]           = 0x03;
+        usb_buf[0x02]           = ALIENWARE_COMMAND_SET_COLOR;
+        usb_buf[0x03]           = RGBGetRValue(color);
+        usb_buf[0x04]           = RGBGetGValue(color);
+        usb_buf[0x05]           = RGBGetBValue(color);
+        usb_buf[0x06]           = num_zones >> 8;
+        usb_buf[0x07]           = num_zones & 0xFF;
+
+        for(size_t i = 0; i < num_zones; i++)
+        {
+            usb_buf[0x08 + i]   = zones[offset + i];
+        }
+
+        /*-------------------------------------------------*\
+        | Send packet                                       |
+        \*-------------------------------------------------*/
+        SendHIDReport(dev, usb_buf, sizeof(usb_buf));
+
+        HidapiAlienwareReport response = GetResponse();
+
+        /*-------------------------------------------------*\
+        | For this command, error is if the output equals   |
+        | the input                                         |
+        \*-------------------------------------------------*/
+        result &= (response.data[1] == 0x03) && memcmp(usb_buf, response.data, HIDAPI_ALIENWARE_REPORT_SIZE);
    }

-    /*-----------------------------------------------------*\
-    | Send packet                                           |
-    \*-----------------------------------------------------*/
-    SendHIDReport(dev, usb_buf, sizeof(usb_buf));
-
-    HidapiAlienwareReport response = GetResponse();
-
-    /*-----------------------------------------------------*\
-    | For this command, error is if the output equals the   |
-    | input                                                 |
-    \*-----------------------------------------------------*/
-    return((response.data[1] == 0x03) && memcmp(usb_buf, response.data, HIDAPI_ALIENWARE_REPORT_SIZE));
+    return(result);
 }

 bool AlienwareController::Reset()
@@ -640,6 +702,15 @@ void AlienwareController::SetDim(uint8_t zone, uint8_t dim)
    }
 }

+void AlienwareController::SetDirection(uint8_t zone, uint8_t direction)
+{
+    if(zone < zones.size())
+    {
+        zones[zone].direction   = direction;
+        dirty                   = true;
+    }
+}
+
 void AlienwareController::UpdateDim()
 {
    if(!dirty_dim)
@@ -655,7 +726,8 @@ void AlienwareController::UpdateDim()

    for(size_t i = 0; i < zones.size(); i++)
    {
-        dim_zone_map[zones[i].dim].emplace_back((uint8_t)i);
+        uint8_t hw_zone = (i < zone_ids.size()) ? zone_ids[i] : static_cast<uint8_t>(i);
+        dim_zone_map[zones[i].dim].emplace_back(hw_zone);
    }

    for(std::pair<const uint8_t, std::vector<uint8_t>> &pair : dim_zone_map)
@@ -682,7 +754,8 @@ bool AlienwareController::UpdateDirect()

    for(size_t i = 0; i < zones.size(); i++)
    {
-        color_zone_map[zones[i].color[0]].emplace_back((uint8_t)i);
+        uint8_t hw_zone = (i < zone_ids.size()) ? zone_ids[i] : static_cast<uint8_t>(i);
+        color_zone_map[zones[i].color[0]].emplace_back(hw_zone);
    }

    for(std::pair<const RGBColor, std::vector<uint8_t>> &pair : color_zone_map)
@@ -726,8 +799,9 @@ void AlienwareController::UpdateMode()
    for(std::size_t zone_idx = 0; zone_idx < zones.size(); zone_idx++)
    {
        alienware_zone zone = zones[zone_idx];
+        uint8_t hw_zone = (zone_idx < zone_ids.size()) ? zone_ids[zone_idx] : static_cast<uint8_t>(zone_idx);

-        result = SelectZones({static_cast<uint8_t>(zone_idx)});
+        result = SelectZones({hw_zone});

        if(!result)
        {
@@ -750,18 +824,18 @@ void AlienwareController::UpdateMode()

            case ALIENWARE_MODE_MORPH:
                {
-                    uint8_t  zones[2]   = { zone.mode,              zone.mode     };
+                    uint8_t  modes[2]   = { zone.mode,              zone.mode     };
                    uint16_t periods[2] = { zone.period,            zone.period   };
                    uint16_t tempos[2]  = { zone.tempo,             zone.tempo    };
                    RGBColor colors[2]  = { zone.color[0],          zone.color[1] };

-                    result = MultiModeAction(zones, periods, tempos, colors, 2);
+                    result = MultiModeAction(modes, periods, tempos, colors, 2);
                }
                break;

            case ALIENWARE_MODE_SPECTRUM:
                {
-                    uint8_t  zones[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                    uint8_t  modes[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                            ALIENWARE_MODE_MORPH };
@@ -774,13 +848,13 @@ void AlienwareController::UpdateMode()
                                            zone.tempo,             zone.tempo,
                                            zone.tempo };

-                    result = MultiModeAction(zones, periods, tempos, rainbow_colors[0], 7);
+                    result = MultiModeAction(modes, periods, tempos, rainbow_colors[0], 7);
                }
                break;

            case ALIENWARE_MODE_RAINBOW:
                {
-                    uint8_t  zones[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                    uint8_t  modes[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
                                            ALIENWARE_MODE_MORPH };
@@ -793,18 +867,19 @@ void AlienwareController::UpdateMode()
                                            zone.tempo,             zone.tempo,
                                            zone.tempo };

-                    result = MultiModeAction(zones, periods, tempos, rainbow_colors[zone_idx], 7);
+                    unsigned int color_idx = (zone.direction == MODE_DIRECTION_LEFT) ? (4 - 1 - (zone_idx % 4)) : (zone_idx % 4);
+                    result = MultiModeAction(modes, periods, tempos, rainbow_colors[color_idx], 7);
                }
                break;

            case ALIENWARE_MODE_BREATHING:
                {
-                    uint8_t  zones[2]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH };
+                    uint8_t  modes[2]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH };
                    uint16_t periods[2] = { zone.period,            zone.period          };
                    uint16_t tempos[2]  = { zone.tempo,             zone.tempo           };
                    RGBColor colors[2]  = { zone.color[0],          0x0                  };

-                    result = MultiModeAction(zones, periods, tempos, colors, 2);
+                    result = MultiModeAction(modes, periods, tempos, colors, 2);
                }
                break;

@@ -831,6 +906,117 @@ void AlienwareController::UpdateMode()
    dirty = false;
 }

+void AlienwareController::SaveController()
+{
+    /*-----------------------------------------------------*\
+    | Save current mode configuration to EEPROM slot 0x0061 |
+    \*-----------------------------------------------------*/
+    UserAnimation(ALIENWARE_COMMAND_USER_ANIM_REMOVE, ALIENWARE_ANIM_DEFAULT, 0);
+    bool result = UserAnimation(ALIENWARE_COMMAND_USER_ANIM_NEW, ALIENWARE_ANIM_DEFAULT, 0);
+
+    if(!result)
+    {
+        return;
+    }
+
+    for(std::size_t zone_idx = 0; zone_idx < zones.size(); zone_idx++)
+    {
+        alienware_zone zone = zones[zone_idx];
+        uint8_t hw_zone = (zone_idx < zone_ids.size()) ? zone_ids[zone_idx] : static_cast<uint8_t>(zone_idx);
+
+        result = SelectZones({hw_zone});
+
+        if(!result)
+        {
+            return;
+        }
+
+        switch (zone.mode)
+        {
+            case ALIENWARE_MODE_COLOR:
+                result = ModeAction(zone.mode, 2000, ALIENWARE_TEMPO_MAX, zone.color[0]);
+                break;
+
+            case ALIENWARE_MODE_PULSE:
+                result = ModeAction(zone.mode, zone.period, zone.tempo, zone.color[0]);
+                break;
+
+            case ALIENWARE_MODE_MORPH:
+                {
+                    uint8_t  modes[2]   = { zone.mode,              zone.mode     };
+                    uint16_t periods[2] = { zone.period,            zone.period   };
+                    uint16_t tempos[2]  = { zone.tempo,             zone.tempo    };
+                    RGBColor colors[2]  = { zone.color[0],          zone.color[1] };
+
+                    result = MultiModeAction(modes, periods, tempos, colors, 2);
+                }
+                break;
+
+            case ALIENWARE_MODE_SPECTRUM:
+                {
+                    uint8_t  modes[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH };
+                    uint16_t periods[7] = { zone.period,            zone.period,
+                                            zone.period,            zone.period,
+                                            zone.period,            zone.period,
+                                            zone.period };
+                    uint16_t tempos[7] = {  zone.tempo,             zone.tempo,
+                                            zone.tempo,             zone.tempo,
+                                            zone.tempo,             zone.tempo,
+                                            zone.tempo };
+
+                    result = MultiModeAction(modes, periods, tempos, rainbow_colors[0], 7);
+                }
+                break;
+
+            case ALIENWARE_MODE_RAINBOW:
+                {
+                    uint8_t  modes[7]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH,
+                                            ALIENWARE_MODE_MORPH };
+                    uint16_t periods[7] = { zone.period,            zone.period,
+                                            zone.period,            zone.period,
+                                            zone.period,            zone.period,
+                                            zone.period };
+                    uint16_t tempos[7]  = { zone.tempo,             zone.tempo,
+                                            zone.tempo,             zone.tempo,
+                                            zone.tempo,             zone.tempo,
+                                            zone.tempo };
+
+                    unsigned int color_idx = (zone.direction == MODE_DIRECTION_LEFT) ? (4 - 1 - (zone_idx % 4)) : (zone_idx % 4);
+                    result = MultiModeAction(modes, periods, tempos, rainbow_colors[color_idx], 7);
+                }
+                break;
+
+            case ALIENWARE_MODE_BREATHING:
+                {
+                    uint8_t  modes[2]   = { ALIENWARE_MODE_MORPH,   ALIENWARE_MODE_MORPH };
+                    uint16_t periods[2] = { zone.period,            zone.period          };
+                    uint16_t tempos[2]  = { zone.tempo,             zone.tempo           };
+                    RGBColor colors[2]  = { zone.color[0],          0x0                  };
+
+                    result = MultiModeAction(modes, periods, tempos, colors, 2);
+                }
+                break;
+
+            default:
+                result = false;
+        }
+
+        if(!result)
+        {
+            return;
+        }
+    }
+
+    UserAnimation(ALIENWARE_COMMAND_USER_ANIM_FINISH_SAVE, ALIENWARE_ANIM_DEFAULT, 0);
+    UserAnimation(ALIENWARE_COMMAND_USER_ANIM_DEFAULT, ALIENWARE_ANIM_DEFAULT, 0);
+    UserAnimation(ALIENWARE_COMMAND_USER_ANIM_STARTUP, ALIENWARE_ANIM_DEFAULT, 0);
+}
+
 void AlienwareController::UpdateController()
 {
    UpdateMode();
@@ -22,6 +22,14 @@
 #define ALIENWARE_REPORT_SIZE               33
 #define HIDAPI_ALIENWARE_REPORT_SIZE        (ALIENWARE_REPORT_SIZE + 1)
 #define ALIENWARE_CONTROLLER_NAME           "AlienWare Controller"
+
+/*---------------------------------------------------------*\
+| Max zone IDs that fit in one report after the command     |
+| header.  Selections larger than this must be split across |
+| multiple packets; writing them into a single report       |
+| overflows usb_buf (e.g. desktops with ~100 zones).        |
+\*---------------------------------------------------------*/
+#define ALIENWARE_MAX_ZONES_PER_PACKET      25
 enum
 {
    ALIENWARE_COMMAND_REPORT                = 0x20,     /* Set report type to get               */
@@ -115,11 +123,13 @@ public:
    void                        SetPeriod(uint8_t zone, uint16_t period);
    void                        SetTempo(uint8_t zone, uint16_t tempo);
    void                        SetDim(uint8_t zone, uint8_t dim);
+    void                        SetDirection(uint8_t zone, uint8_t direction);
    AlienwareReport             GetStatus(uint8_t subcommand);

    void                        UpdateDim();
    void                        UpdateMode();
    void                        UpdateController();
+    void                        SaveController();

 protected:
    hid_device* dev;
@@ -132,6 +142,7 @@ private:
        uint16_t                period;
        uint16_t                tempo;
        uint8_t                 dim;
+        uint8_t                 direction;
    } alienware_zone;

    typedef struct
@@ -145,6 +156,7 @@ private:
    std::string                 serial_number;
    std::string                 version;
    std::vector<const char*>    zone_names;
+    std::vector<uint8_t>        zone_ids;
    bool                        dirty;
    bool                        dirty_dim;

@@ -39,7 +39,7 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
    mode Color;
    Color.name                 = "Static";
    Color.value                = ALIENWARE_MODE_COLOR;
-    Color.flags                = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS;
+    Color.flags                = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_MANUAL_SAVE;
    Color.color_mode           = MODE_COLORS_PER_LED;
    Color.colors_min           = 1;
    Color.colors_max           = 1;
@@ -51,13 +51,13 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
    mode Pulse;
    Pulse.name                 = "Flashing";
    Pulse.value                = ALIENWARE_MODE_PULSE;
-    Pulse.flags                = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Pulse.flags                = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED | MODE_FLAG_MANUAL_SAVE;
    Pulse.color_mode           = MODE_COLORS_PER_LED;
    Pulse.colors_min           = 1;
    Pulse.colors_max           = 1;
-    Pulse.speed_min            = ALIENWARE_TEMPO_MIN;
-    Pulse.speed_max            = ALIENWARE_TEMPO_MAX;
-    Pulse.speed                = ALIENWARE_TEMPO_MIN;
+    Pulse.speed_min            = ALIENWARE_TEMPO_MAX;
+    Pulse.speed_max            = 50;
+    Pulse.speed                = 150;
    Pulse.brightness_min       = 100;
    Pulse.brightness_max       = 0;
    Pulse.brightness           = 0;
@@ -66,14 +66,16 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
    mode Morph;
    Morph.name                 = "Morph";
    Morph.value                = ALIENWARE_MODE_MORPH;
-    Morph.flags                = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Morph.flags                = MODE_FLAG_HAS_MODE_SPECIFIC_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED | MODE_FLAG_MANUAL_SAVE;
    Morph.color_mode           = MODE_COLORS_MODE_SPECIFIC;
-    Morph.colors_min           = 2 * controller->GetZoneCount();
-    Morph.colors_max           = Morph.colors_min;
-    Morph.colors.resize(Morph.colors_max);
-    Morph.speed_min            = ALIENWARE_TEMPO_MIN;
-    Morph.speed_max            = ALIENWARE_TEMPO_MAX;
-    Morph.speed                = ALIENWARE_TEMPO_MIN;
+    Morph.colors_min           = 2;
+    Morph.colors_max           = 2 * controller->GetZoneCount();
+    Morph.colors.resize(2);
+    Morph.colors[0]            = 0x0000FF;
+    Morph.colors[1]            = 0xFF0000;
+    Morph.speed_min            = ALIENWARE_TEMPO_MAX;
+    Morph.speed_max            = 20;
+    Morph.speed                = 100;
    Morph.brightness_min       = 100;
    Morph.brightness_max       = 0;
    Morph.brightness           = 0;
@@ -82,11 +84,11 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
    mode Spectrum;
    Spectrum.name              = "Spectrum Cycle";
    Spectrum.value             = ALIENWARE_MODE_SPECTRUM;
-    Spectrum.flags             = MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Spectrum.flags             = MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED | MODE_FLAG_MANUAL_SAVE;
    Spectrum.color_mode        = MODE_COLORS_NONE;
-    Spectrum.speed_min         = ALIENWARE_TEMPO_SPECTRUM;
-    Spectrum.speed_max         = ALIENWARE_TEMPO_MAX;
-    Spectrum.speed             = ALIENWARE_TEMPO_SPECTRUM;
+    Spectrum.speed_min         = ALIENWARE_TEMPO_MAX;
+    Spectrum.speed_max         = ALIENWARE_TEMPO_SPECTRUM;
+    Spectrum.speed             = 40;
    Spectrum.brightness_min    = 100;
    Spectrum.brightness_max    = 0;
    Spectrum.brightness        = 0;
@@ -95,11 +97,12 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
    mode Rainbow;
    Rainbow.name               = "Rainbow Wave";
    Rainbow.value              = ALIENWARE_MODE_RAINBOW;
-    Rainbow.flags              = MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Rainbow.flags              = MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED | MODE_FLAG_HAS_DIRECTION_LR | MODE_FLAG_MANUAL_SAVE;
    Rainbow.color_mode         = MODE_COLORS_NONE;
-    Rainbow.speed_min          = ALIENWARE_TEMPO_SPECTRUM;
-    Rainbow.speed_max          = ALIENWARE_TEMPO_MAX;
-    Rainbow.speed              = ALIENWARE_TEMPO_SPECTRUM;
+    Rainbow.speed_min          = ALIENWARE_TEMPO_MAX;
+    Rainbow.speed_max          = ALIENWARE_TEMPO_SPECTRUM;
+    Rainbow.speed              = 40;
+    Rainbow.direction          = MODE_DIRECTION_RIGHT;
    Rainbow.brightness_min     = 100;
    Rainbow.brightness_max     = 0;
    Rainbow.brightness         = 0;
@@ -108,13 +111,13 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
    mode Breathing;
    Breathing.name             = "Breathing";
    Breathing.value            = ALIENWARE_MODE_BREATHING;
-    Breathing.flags            = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED;
+    Breathing.flags            = MODE_FLAG_HAS_PER_LED_COLOR | MODE_FLAG_HAS_BRIGHTNESS | MODE_FLAG_HAS_SPEED | MODE_FLAG_MANUAL_SAVE;
    Breathing.color_mode       = MODE_COLORS_PER_LED;
    Breathing.colors_min       = 1;
    Breathing.colors_max       = 1;
-    Breathing.speed_min        = ALIENWARE_TEMPO_MIN;
-    Breathing.speed_max        = ALIENWARE_TEMPO_MAX;
-    Breathing.speed            = ALIENWARE_TEMPO_MIN;
+    Breathing.speed_min        = ALIENWARE_TEMPO_MAX;
+    Breathing.speed_max        = 50;
+    Breathing.speed            = 150;
    Breathing.brightness_min   = 100;
    Breathing.brightness_max   = 0;
    Breathing.brightness       = 0;
@@ -125,6 +128,13 @@ RGBController_Alienware::RGBController_Alienware(AlienwareController* controller
    controller->UpdateDim();
 }

+RGBController_Alienware::~RGBController_Alienware()
+{
+    Shutdown();
+
+    delete controller;
+}
+
 void RGBController_Alienware::SetupZones()
 {
    /*-------------------------------------------------*\
@@ -217,6 +227,7 @@ void RGBController_Alienware::DeviceUpdateMode()
            uint16_t period = 0x07d0;

            controller->SetMode(zone_idx, current_mode.value);
+            controller->SetDirection(zone_idx, current_mode.direction);

            switch(current_mode_idx)
            {
@@ -228,6 +239,7 @@ void RGBController_Alienware::DeviceUpdateMode()
                    break;

                case ALIENWARE_MODE_PULSE:
+                    period = std::max<uint16_t>(500, (uint16_t)(current_mode.speed * 10));
                    controller->SetPeriod(zone_idx, period);
                    controller->SetColor( zone_idx, colors[current_zone.start_idx]);
                    controller->SetTempo( zone_idx, current_mode.speed);
@@ -235,10 +247,22 @@ void RGBController_Alienware::DeviceUpdateMode()
                    break;

                case ALIENWARE_MODE_MORPH:
-                    controller->SetPeriod(zone_idx, period);
-                    controller->SetColor( zone_idx, current_mode.colors[zone_idx * 2], current_mode.colors[(zone_idx * 2) + 1]);
-                    controller->SetTempo( zone_idx, current_mode.speed);
-                    controller->SetDim(   zone_idx, modes[current_mode_idx].brightness);
+                    {
+                        RGBColor c1 = (current_mode.colors.size() >= 1) ? current_mode.colors[0] : 0x0000FF;
+                        RGBColor c2 = (current_mode.colors.size() >= 2) ? current_mode.colors[1] : 0xFF0000;
+
+                        if(current_mode.colors.size() >= (std::size_t)((zone_idx + 1) * 2))
+                        {
+                            c1 = current_mode.colors[zone_idx * 2];
+                            c2 = current_mode.colors[(zone_idx * 2) + 1];
+                        }
+
+                        period = std::max<uint16_t>(400, (uint16_t)(current_mode.speed * 10));
+                        controller->SetPeriod(zone_idx, period);
+                        controller->SetColor( zone_idx, c1, c2);
+                        controller->SetTempo( zone_idx, current_mode.speed);
+                        controller->SetDim(   zone_idx, modes[current_mode_idx].brightness);
+                    }
                    break;

                case ALIENWARE_MODE_SPECTRUM:
@@ -249,6 +273,7 @@ void RGBController_Alienware::DeviceUpdateMode()
                    break;

                case ALIENWARE_MODE_BREATHING:
+                    period = std::max<uint16_t>(500, (uint16_t)(current_mode.speed * 10));
                    controller->SetPeriod(zone_idx, period);
                    controller->SetColor( zone_idx, colors[current_zone.start_idx], 0x0);
                    controller->SetTempo( zone_idx, current_mode.speed);
@@ -275,3 +300,9 @@ void RGBController_Alienware::DeviceUpdateMode()
        current_mode              = new_current_mode;
    }
 }
+
+void RGBController_Alienware::DeviceSaveMode()
+{
+    controller->SaveController();
+}
+
@@ -19,6 +19,7 @@ class RGBController_Alienware : public RGBController
 {
 public:
    RGBController_Alienware(AlienwareController* controller_ptr);
+    ~RGBController_Alienware();

    void        SetupZones();

@@ -27,6 +28,7 @@ public:
    void        DeviceUpdateSingleLED(int led);

    void        DeviceUpdateMode();
+    void        DeviceSaveMode();

 private:
    AlienwareController*                    controller;
@@ -1,7 +1,7 @@
 /*---------------------------------------------------------*\
-| AlienwareKeyboardControllerDetect.cpp                     |
+| AlienwareAW410KControllerDetect.cpp                       |
 |                                                           |
-|   Detector for Alienware Keyboard                         |
+|   Detector for Alienware AW410K Keyboard                  |
 |                                                           |
 |   This file is part of the OpenRGB project                |
 |   SPDX-License-Identifier: GPL-2.0-or-later               |
@@ -10,38 +10,17 @@
 #include <hidapi.h>
 #include "DetectionManager.h"
 #include "AlienwareAW410KController.h"
-#include "AlienwareAW510KController.h"
 #include "RGBController_AlienwareAW410K.h"
-#include "RGBController_AlienwareAW510K.h"

 /*---------------------------------------------------------*\
 | Alienware vendor ID                                       |
 \*---------------------------------------------------------*/
-#define ALIENWARE_VID                           0x04F2
+#define ALIENWARE_VID                               0x04F2

 /*---------------------------------------------------------*\
 | Keyboard product IDs                                      |
 \*---------------------------------------------------------*/
-#define ALIENWARE_AW510K_PID                    0x1830
-#define ALIENWARE_AW410K_PID                    0x1968
-
-DetectedControllers DetectAlienwareAW510KControllers(hid_device_info* info, const std::string& name)
-{
-    DetectedControllers detected_controllers;
-    hid_device*         dev;
-
-    dev = hid_open_path(info->path);
-
-    if(dev)
-    {
-        AlienwareAW510KController*     controller     = new AlienwareAW510KController(dev, info->path, name);
-        RGBController_AlienwareAW510K* rgb_controller = new RGBController_AlienwareAW510K(controller);
-
-        detected_controllers.push_back(rgb_controller);
-    }
-
-    return(detected_controllers);
-}
+#define ALIENWARE_AW410K_PID                        0x1968

 DetectedControllers DetectAlienwareAW410KControllers(hid_device_info* info, const std::string& name)
 {
@@ -61,5 +40,4 @@ DetectedControllers DetectAlienwareAW410KControllers(hid_device_info* info, cons
    return(detected_controllers);
 }

-REGISTER_HID_DETECTOR_IPU("Alienware AW510K",   DetectAlienwareAW510KControllers,   ALIENWARE_VID,  ALIENWARE_AW510K_PID,   0x02,   0xFF00, 0x01);
 REGISTER_HID_DETECTOR_IPU("Alienware AW410K",   DetectAlienwareAW410KControllers,   ALIENWARE_VID,  ALIENWARE_AW410K_PID,   0x02,   0xFF00, 0x01);
@@ -278,6 +278,8 @@ RGBController_AlienwareAW410K::RGBController_AlienwareAW410K(AlienwareAW410KCont

 RGBController_AlienwareAW410K::~RGBController_AlienwareAW410K()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -0,0 +1,43 @@
+/*---------------------------------------------------------*\
+| AlienwareAW510KControllerDetect.cpp                       |
+|                                                           |
+|   Detector for Alienware AW510K Keyboard                  |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include <hidapi.h>
+#include "DetectionManager.h"
+#include "AlienwareAW510KController.h"
+#include "RGBController_AlienwareAW510K.h"
+
+/*---------------------------------------------------------*\
+| Alienware vendor ID                                       |
+\*---------------------------------------------------------*/
+#define ALIENWARE_VID                               0x04F2
+
+/*---------------------------------------------------------*\
+| Keyboard product IDs                                      |
+\*---------------------------------------------------------*/
+#define ALIENWARE_AW510K_PID                        0x1830
+
+DetectedControllers DetectAlienwareAW510KControllers(hid_device_info* info, const std::string& name)
+{
+    DetectedControllers detected_controllers;
+    hid_device*         dev;
+
+    dev = hid_open_path(info->path);
+
+    if(dev)
+    {
+        AlienwareAW510KController*     controller     = new AlienwareAW510KController(dev, info->path, name);
+        RGBController_AlienwareAW510K* rgb_controller = new RGBController_AlienwareAW510K(controller);
+
+        detected_controllers.push_back(rgb_controller);
+    }
+
+    return(detected_controllers);
+}
+
+REGISTER_HID_DETECTOR_IPU("Alienware AW510K",   DetectAlienwareAW510KControllers,   ALIENWARE_VID,  ALIENWARE_AW510K_PID,   0x02,   0xFF00, 0x01);
@@ -277,6 +277,8 @@ RGBController_AlienwareAW510K::RGBController_AlienwareAW510K(AlienwareAW510KCont

 RGBController_AlienwareAW510K::~RGBController_AlienwareAW510K()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -40,11 +40,11 @@ std::vector<unsigned char> AlienwareAW3423DWFController::GetReportResponse()

 void AlienwareAW3423DWFController::PerformLogin()
 {
-    unsigned char init_packet[64] =
-    {
-        0x40, 0xE1, 0x01
-    };
-    SendControlPacket(init_packet, 4);
+    unsigned char init_packet[192] = {0x00};
+    init_packet[0] = 0x40;
+    init_packet[1] = 0xE1;
+    init_packet[2] = 0x01;
+    SendControlPacket(init_packet, 192);

    std::vector<unsigned char> response = GetReportResponse();

@@ -0,0 +1,47 @@
+/*---------------------------------------------------------*\
+| AlienwareAW3423DWFControllerDetect.cpp                    |
+|                                                           |
+|   Detector for Alienware AW3423DWF monitor                |
+|                                                           |
+|   Ferréol DUBOIS COLI (Fefe_du_973)           23 Jan 2025 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include <hidapi.h>
+#include "AlienwareAW3423DWFController.h"
+#include "DetectionManager.h"
+#include "RGBController_AlienwareAW3423DWF.h"
+
+/*---------------------------------------------------------*\
+| Alienware Vendor ID                                       |
+\*---------------------------------------------------------*/
+#define ALIENWARE_VID                               0x187C
+
+/*---------------------------------------------------------*\
+| Alienware Vendor ID                                       |
+\*---------------------------------------------------------*/
+#define ALIENWARE_AW3423DWF_PID                     0x100E
+#define ALIENWARE_USAGE_PAGE                        0xFFDA
+#define ALIENWARE_USAGE                             0x00DA
+
+DetectedControllers DetectAlienwareAW3423DWFControllers(hid_device_info* info, const std::string&)
+{
+    DetectedControllers detected_controllers;
+    hid_device*         dev;
+
+    dev = hid_open_path(info->path);
+
+    if(dev)
+    {
+        AlienwareAW3423DWFController*     controller     = new AlienwareAW3423DWFController(dev, info->path);
+        RGBController_AlienwareAW3423DWF* rgb_controller = new RGBController_AlienwareAW3423DWF(controller);
+
+        detected_controllers.push_back(rgb_controller);
+    }
+
+    return(detected_controllers);
+}
+
+REGISTER_HID_DETECTOR("Alienware AW3423DWF", DetectAlienwareAW3423DWFControllers, ALIENWARE_VID, ALIENWARE_AW3423DWF_PID);
@@ -46,6 +46,8 @@ RGBController_AlienwareAW3423DWF::RGBController_AlienwareAW3423DWF(AlienwareAW34

 RGBController_AlienwareAW3423DWF::~RGBController_AlienwareAW3423DWF()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -10,10 +10,8 @@
 \*---------------------------------------------------------*/

 #include <hidapi.h>
-#include "AlienwareAW3423DWFController.h"
 #include "AlienwareMonitorController.h"
 #include "DetectionManager.h"
-#include "RGBController_AlienwareAW3423DWF.h"
 #include "RGBController_AlienwareMonitor.h"

 /*---------------------------------------------------------*\
@@ -24,29 +22,10 @@
 /*---------------------------------------------------------*\
 | Alienware Vendor ID                                       |
 \*---------------------------------------------------------*/
-#define ALIENWARE_AW3423DWF_PID                     0x100E
 #define ALIENWARE_AW3225QF_PID                      0x1013
 #define ALIENWARE_USAGE_PAGE                        0xFFDA
 #define ALIENWARE_USAGE                             0x00DA

-DetectedControllers DetectAlienwareAW3423DWFControllers(hid_device_info* info, const std::string&)
-{
-    DetectedControllers detected_controllers;
-    hid_device*         dev;
-
-    dev = hid_open_path(info->path);
-
-    if(dev)
-    {
-        AlienwareAW3423DWFController*     controller     = new AlienwareAW3423DWFController(dev, info->path);
-        RGBController_AlienwareAW3423DWF* rgb_controller = new RGBController_AlienwareAW3423DWF(controller);
-
-        detected_controllers.push_back(rgb_controller);
-    }
-
-    return(detected_controllers);
-}
-
 DetectedControllers DetectAlienwareMonitorControllers(hid_device_info* info, const std::string& name)
 {
    DetectedControllers detected_controllers;
@@ -65,5 +44,4 @@ DetectedControllers DetectAlienwareMonitorControllers(hid_device_info* info, con
    return(detected_controllers);
 }

-REGISTER_HID_DETECTOR("Alienware AW3423DWF", DetectAlienwareAW3423DWFControllers, ALIENWARE_VID, ALIENWARE_AW3423DWF_PID);
 REGISTER_HID_DETECTOR("Alienware AW3225QF", DetectAlienwareMonitorControllers, ALIENWARE_VID, ALIENWARE_AW3225QF_PID);
@@ -46,6 +46,8 @@ RGBController_AlienwareMonitor::RGBController_AlienwareMonitor(AlienwareMonitorC

 RGBController_AlienwareMonitor::~RGBController_AlienwareMonitor()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -144,6 +144,8 @@ RGBController_AnnePro2::RGBController_AnnePro2(AnnePro2Controller* controller_pt

 RGBController_AnnePro2::~RGBController_AnnePro2()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -21,13 +21,13 @@
 DetectedControllers DetectArcticControllers()
 {
    DetectedControllers         detected_controllers;
-    std::vector<std::string *>  ports;
+    std::vector<std::string>    ports;

    ports = find_usb_serial_port(CH341_VID, CH341_PID);

    for(unsigned int device = 0; device < ports.size(); device++)
    {
-        ArcticController *controller = new ArcticController(*ports[device]);
+        ArcticController *controller = new ArcticController(ports[device]);

        if(controller->IsPresent())
        {
@@ -38,16 +38,10 @@ DetectedControllers DetectArcticControllers()
        {
            delete controller;
        }
-
-        delete ports[device];
    }

    return(detected_controllers);
 }

 REGISTER_DETECTOR("Arctic RGB controller", DetectArcticControllers);
-/*---------------------------------------------------------------------------------------------------------*\
-| Entries for dynamic UDEV rules                                                                            |
-|                                                                                                           |
-| DUMMY_DEVICE_DETECTOR("Arctic RGB controller", DetectArcticControllers, 0x1A86, 0x7523 )                  |
-\*---------------------------------------------------------------------------------------------------------*/
+REGISTER_CUSTOM_UDEV_RULE(arctic, "Arctic RGB controller", "SUBSYSTEMS==\"serial|hidraw\", ATTRS{idVendor}==\"1a86\", ATTRS{idProduct}==\"7523\", TAG+=\"uaccess\", TAG+=\"Arctic_RGB_controller\"");
@@ -55,6 +55,8 @@ RGBController_Arctic::RGBController_Arctic(ArcticController* controller_ptr)

 RGBController_Arctic::~RGBController_Arctic()
 {
+    Shutdown();
+
    keepalive_thread_run = false;
    keepalive_thread.join();
    delete controller;
@@ -125,6 +125,8 @@ RGBController_Areson::RGBController_Areson(AresonController* controller_ptr)

 RGBController_Areson::~RGBController_Areson()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -4,18 +4,15 @@
 |   Detector for ASUS ROG Aura Core                         |
 |                                                           |
 |   Adam Honse (CalcProgrammer1)                13 Apr 2020 |
-|   Chris M (Dr_No)                             28 Jul 2022 |
 |                                                           |
 |   This file is part of the OpenRGB project                |
 |   SPDX-License-Identifier: GPL-2.0-or-later               |
 \*---------------------------------------------------------*/

-#include "DetectionManager.h"
-#include "AsusAuraCoreController.h"
-#include "RGBController.h"
-#include "RGBController_AsusAuraCore.h"
-#include "RGBController_AsusAuraCoreLaptop.h"
 #include <hidapi.h>
+#include "AsusAuraCoreController.h"
+#include "DetectionManager.h"
+#include "RGBController_AsusAuraCore.h"

 #define AURA_CORE_VID                   0x0B05

@@ -44,27 +41,6 @@ DetectedControllers DetectAsusAuraCoreControllers(hid_device_info* info, const s
    return(detected_controllers);
 }

-DetectedControllers DetectAsusAuraCoreLaptopControllers(hid_device_info* info, const std::string& /*name*/)
-{
-    DetectedControllers detected_controllers;
-    hid_device*         dev;
-
-    dev = hid_open_path(info->path);
-
-    if(dev)
-    {
-        AsusAuraCoreLaptopController*     controller        = new AsusAuraCoreLaptopController(dev, info->path);
-        RGBController_AsusAuraCoreLaptop* rgb_controller    = new RGBController_AsusAuraCoreLaptop(controller);
-
-        detected_controllers.push_back(rgb_controller);
-    }
-
-    return(detected_controllers);
-}
-
-
 REGISTER_HID_DETECTOR   ("ASUS Aura Core",              DetectAsusAuraCoreControllers,          AURA_CORE_VID, 0x1854);
 REGISTER_HID_DETECTOR   ("ASUS Aura Core",              DetectAsusAuraCoreControllers,          AURA_CORE_VID, 0x1866);
 REGISTER_HID_DETECTOR   ("ASUS Aura Core",              DetectAsusAuraCoreControllers,          AURA_CORE_VID, 0x1869);
-REGISTER_HID_DETECTOR_PU("ASUS ROG Strix SCAR 15",      DetectAsusAuraCoreLaptopControllers,    AURA_CORE_VID, AURA_STRIX_SCAR_15_PID,  0xFF31, 0x79);
-REGISTER_HID_DETECTOR_PU("ASUS ROG Strix SCAR 17",      DetectAsusAuraCoreLaptopControllers,    AURA_CORE_VID, 0x1866,                  0xFF31, 0x79);
@@ -45,6 +45,13 @@ RGBController_AuraCore::RGBController_AuraCore(AuraCoreController* controller_pt
    SetupZones();
 }

+RGBController_AuraCore::~RGBController_AuraCore()
+{
+    Shutdown();
+
+    delete controller;
+}
+
 void RGBController_AuraCore::SetupKeyboard()
 {
    name                    = "ASUS Aura Keyboard";
@@ -170,11 +177,6 @@ void RGBController_AuraCore::SetupGA15DH()
    modes.push_back(Static);
 }

-RGBController_AuraCore::~RGBController_AuraCore()
-{
-    delete controller;
-}
-
 void RGBController_AuraCore::SetupZones()
 {
    zone auraZone;
@@ -0,0 +1,38 @@
+/*---------------------------------------------------------*\
+| AsusAuraCoreLaptopControllerDetect.cpp                    |
+|                                                           |
+|   Detector for ASUS ROG Aura Core Laptop                  |
+|                                                           |
+|   Chris M (Dr_No)                             28 Jul 2022 |
+|                                                           |
+|   This file is part of the OpenRGB project                |
+|   SPDX-License-Identifier: GPL-2.0-or-later               |
+\*---------------------------------------------------------*/
+
+#include <hidapi.h>
+#include "AsusAuraCoreLaptopController.h"
+#include "DetectionManager.h"
+#include "RGBController_AsusAuraCoreLaptop.h"
+
+#define AURA_CORE_VID                   0x0B05
+
+DetectedControllers DetectAsusAuraCoreLaptopControllers(hid_device_info* info, const std::string& /*name*/)
+{
+    DetectedControllers detected_controllers;
+    hid_device*         dev;
+
+    dev = hid_open_path(info->path);
+
+    if(dev)
+    {
+        AsusAuraCoreLaptopController*     controller        = new AsusAuraCoreLaptopController(dev, info->path);
+        RGBController_AsusAuraCoreLaptop* rgb_controller    = new RGBController_AsusAuraCoreLaptop(controller);
+
+        detected_controllers.push_back(rgb_controller);
+    }
+
+    return(detected_controllers);
+}
+
+REGISTER_HID_DETECTOR_PU("ASUS ROG Strix SCAR 15",      DetectAsusAuraCoreLaptopControllers,    AURA_CORE_VID, AURA_STRIX_SCAR_15_PID,  0xFF31, 0x79);
+REGISTER_HID_DETECTOR_PU("ASUS ROG Strix SCAR 17",      DetectAsusAuraCoreLaptopControllers,    AURA_CORE_VID, 0x1866,                  0xFF31, 0x79);
@@ -940,6 +940,25 @@ static const aura_core_laptop_device g814jv_device =
    }
 };

+/*-------------------------------------------------------------*\
+|  ASUS ROG Strix G18 (G814JIR)                                 |
+|                                                               |
+|  G814JIR uses the same Aura Core keyboard and lightbar        |
+|  layout as the G814JV G18 profile.                            |
+\*-------------------------------------------------------------*/
+static const aura_core_laptop_device g814jir_device =
+{
+    "G814JIR",
+    {
+        &g814rw_keyboard_zone,
+        &g814jv_lightbar_zone,
+        nullptr,
+        nullptr,
+        nullptr,
+        nullptr
+    }
+};
+
 /*-------------------------------------------------------------------------*\
 |  DEVICE MASTER LIST                                                       |
 \*-------------------------------------------------------------------------*/
@@ -954,6 +973,7 @@ const aura_core_laptop_device* aura_core_laptop_device_list_data[] =
    &g713rw_device,
    &g733qr_device,
    &g814jv_device,
+    &g814jir_device,
 };

 const unsigned int AURA_CORE_LAPTOP_DEVICE_COUNT = (sizeof(aura_core_laptop_device_list_data) / sizeof(aura_core_laptop_device_list_data[ 0 ]));
@@ -268,6 +268,8 @@ RGBController_AsusAuraCoreLaptop::RGBController_AsusAuraCoreLaptop(AsusAuraCoreL

 RGBController_AsusAuraCoreLaptop::~RGBController_AsusAuraCoreLaptop()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -32,7 +32,7 @@ std::string AuraGPUController::GetDeviceName()

 std::string AuraGPUController::GetDeviceLocation()
 {
-    std::string return_string(bus->device_name);
+    std::string return_string(bus->info.device_name);
    char addr[5];
    snprintf(addr, 5, "0x%02X", dev);
    return_string.append(", address ");
@@ -79,7 +79,7 @@ void AuraGPUController::AuraGPURegisterWrite(unsigned char reg, unsigned char va

 bool AuraGPUController::SaveOnlyApplies()
 {
-    switch (bus->pci_subsystem_device)
+    switch (bus->info.pci_subsystem_device)
    {
        case ASUS_VEGA64_STRIX:
            return false;
@@ -21,7 +21,7 @@

 bool TestForAsusAuraGPUController(i2c_smbus_interface* bus, unsigned char address)
 {
-    if(bus->pci_vendor == AMD_GPU_VEN && !is_amd_gpu_i2c_bus(bus))
+    if(bus->info.pci_vendor == AMD_GPU_VEN && !is_amd_gpu_i2c_bus(bus))
    {
        return false;
    }
@@ -124,6 +124,8 @@ RGBController_AuraGPU::RGBController_AuraGPU(AuraGPUController * controller_ptr)

 RGBController_AuraGPU::~RGBController_AuraGPU()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -112,6 +112,8 @@ RGBController_AuraHeadsetStand::RGBController_AuraHeadsetStand(AuraHeadsetStandC

 RGBController_AuraHeadsetStand::~RGBController_AuraHeadsetStand()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -380,6 +380,8 @@ RGBController_AuraKeyboard::RGBController_AuraKeyboard(AuraKeyboardController* c

 RGBController_AuraKeyboard::~RGBController_AuraKeyboard()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -45,6 +45,8 @@ RGBController_AuraMonitor::RGBController_AuraMonitor(AuraMonitorController* cont

 RGBController_AuraMonitor::~RGBController_AuraMonitor()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -22,6 +22,7 @@
 #define AURA_ROG_GLADIUS_II_WIRELESS_1_PID              0x189E
 #define AURA_ROG_GLADIUS_II_WIRELESS_2_PID              0x18A0
 #define AURA_ROG_GLADIUS_III_PID                        0x197B
+#define AURA_ROG_GLADIUS_III_CORE_PID                   0x1C8D
 #define AURA_ROG_GLADIUS_III_WIRELESS_USB_PID           0x197D
 #define AURA_ROG_GLADIUS_III_WIRELESS_2_4_PID           0x197F
 #define AURA_ROG_GLADIUS_III_WIRELESS_BT_PID            0x1981
@@ -217,6 +218,20 @@ static std::map<int,mouse_type> aura_mouse_devices =
            { AURA_MOUSE_MODE_STATIC, AURA_MOUSE_MODE_BREATHING, AURA_MOUSE_MODE_SPECTRUM, AURA_MOUSE_MODE_WAVE, AURA_MOUSE_MODE_REACTIVE, AURA_MOUSE_MODE_COMET, AURA_MOUSE_MODE_BATTERY }
        }
    },
+    {
+        AURA_ROG_GLADIUS_III_CORE_PID, // ROG Gladius III Core
+        {
+            0,
+            0,
+            0,
+            100,
+            false,
+            1,
+            false,
+            { AURA_MOUSE_ZONE_LOGO, AURA_MOUSE_ZONE_SCROLL },
+            { AURA_MOUSE_MODE_STATIC, AURA_MOUSE_MODE_BREATHING, AURA_MOUSE_MODE_SPECTRUM, AURA_MOUSE_MODE_NONE, AURA_MOUSE_MODE_REACTIVE }
+        }
+    },
    {
        AURA_ROG_GLADIUS_III_WIRELESS_USB_PID, // ROG Gladius III Wireless USB
        {
@@ -185,6 +185,8 @@ RGBController_AuraMouse::RGBController_AuraMouse(AuraMouseController* controller

 RGBController_AuraMouse::~RGBController_AuraMouse()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -116,6 +116,8 @@ RGBController_AsusROGSpatha::RGBController_AsusROGSpatha(AsusAuraMouseGen1Contro

 RGBController_AsusROGSpatha::~RGBController_AsusROGSpatha()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -79,6 +79,8 @@ RGBController_AsusROGStrixEvolve::RGBController_AsusROGStrixEvolve(AsusAuraMouse

 RGBController_AsusROGStrixEvolve::~RGBController_AsusROGStrixEvolve()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -182,6 +182,8 @@ RGBController_AuraMousemat::RGBController_AuraMousemat(AuraMousematController* c

 RGBController_AuraMousemat::~RGBController_AuraMousemat()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -19,7 +19,10 @@ AsusAuraRyuoAIOController::AsusAuraRyuoAIOController(hid_device* dev_handle, con
    |    Manually adding device info for now                |
    |    TODO: Implement config table accurately            |
    \*-----------------------------------------------------*/
-    device_info.push_back({0x00, 0x00, 12, 0, AuraDeviceType::FIXED});
+    uint8_t leds = (dev_name.find("Ryujin") != std::string::npos) ? 5 : 12;
+
+    device_info.push_back({0x00, 0x00, leds, 0, AuraDeviceType::FIXED});
+
 }

 AsusAuraRyuoAIOController::~AsusAuraRyuoAIOController()
@@ -128,6 +128,8 @@ RGBController_AsusAuraRyuoAIO::RGBController_AsusAuraRyuoAIO(AsusAuraRyuoAIOCont

 RGBController_AsusAuraRyuoAIO::~RGBController_AsusAuraRyuoAIO()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -410,6 +410,8 @@ RGBController_AuraTUFKeyboard::RGBController_AuraTUFKeyboard(AuraTUFKeyboardCont

 RGBController_AuraTUFKeyboard::~RGBController_AuraTUFKeyboard()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -426,7 +428,6 @@ void RGBController_AuraTUFKeyboard::SetupZones()
            break;
        case AURA_TUF_K3_GAMING_PID:
        case AURA_TUF_K7_GAMING_PID:
-        case AURA_TUF_K3_GENII_MIKU_EDITION_PID:
            keyboard_ptr = &AsusTUFK7Layouts;
            break;
        case AURA_ROG_STRIX_SCOPE_PID:
@@ -483,6 +484,7 @@ void RGBController_AuraTUFKeyboard::SetupZones()
            keyboard_ptr = &AsusTufK1Layouts;
            break;
        case AURA_TUF_K3_GAMING_GEN_II_PID:
+        case AURA_TUF_K3_GENII_MIKU_EDITION_PID:
            keyboard_ptr = &AsusTUFK3GamingGen2Layouts;
            break;
        default:
@@ -119,6 +119,8 @@ RGBController_AuraUSB::RGBController_AuraUSB(AuraUSBController* controller_ptr)

 RGBController_AuraUSB::~RGBController_AuraUSB()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -145,41 +147,68 @@ void RGBController_AuraUSB::SetupZones()
    | Set zones and leds                                |
    \*-------------------------------------------------*/
    int addressableCounter = 1;
-    for (unsigned int channel_idx = 0; channel_idx < zones.size(); channel_idx++)
+
+    for(std::size_t channel_idx = 0; channel_idx < zones.size(); channel_idx++)
    {
        AuraDeviceInfo device_info  = controller->GetAuraDevices()[channel_idx];

-        zones[channel_idx].type     = ZONE_TYPE_LINEAR;
-
        if(device_info.device_type == AuraDeviceType::FIXED)
        {
-            zones[channel_idx].name       = "Aura Mainboard";
-            zones[channel_idx].leds_min   = device_info.num_leds;
-            zones[channel_idx].leds_max   = device_info.num_leds;
-            zones[channel_idx].leds_count = device_info.num_leds;
+            zones[channel_idx].name                     = "Aura Mainboard";
+            zones[channel_idx].type                     = ZONE_TYPE_LINEAR;
+            zones[channel_idx].leds_min                 = device_info.num_leds;
+            zones[channel_idx].leds_max                 = device_info.num_leds;
+            zones[channel_idx].leds_count               = device_info.num_leds;
        }
        else
        {
-            zones[channel_idx].name       = "Aura Addressable ";
-            zones[channel_idx].name.append(std::to_string(addressableCounter));
-            zones[channel_idx].leds_min   = 0;
-            zones[channel_idx].leds_max   = AURA_ADDRESSABLE_MAX_LEDS;
-
-            addressableCounter++;
+            zones[channel_idx].leds_min                 = 0;
+            zones[channel_idx].leds_max                 = AURA_ADDRESSABLE_MAX_LEDS;

            if(first_run)
            {
-                zones[channel_idx].leds_count = 0;
+                zones[channel_idx].flags                = ZONE_FLAG_MANUALLY_CONFIGURABLE_SIZE
+                                                        | ZONE_FLAG_MANUALLY_CONFIGURABLE_NAME
+                                                        | ZONE_FLAG_MANUALLY_CONFIGURABLE_TYPE
+                                                        | ZONE_FLAG_MANUALLY_CONFIGURABLE_MATRIX_MAP
+                                                        | ZONE_FLAG_MANUALLY_CONFIGURABLE_SEGMENTS;
            }
+
+            if(!(zones[channel_idx].flags & ZONE_FLAG_MANUALLY_CONFIGURED_NAME))
+            {
+                zones[channel_idx].name                 = "Addressable RGB Header ";
+                zones[channel_idx].name.append(std::to_string(addressableCounter));
+            }
+
+            if(!(zones[channel_idx].flags & ZONE_FLAG_MANUALLY_CONFIGURED_SIZE))
+            {
+                zones[channel_idx].leds_count           = 0;
+            }
+
+            if(!(zones[channel_idx].flags & ZONE_FLAG_MANUALLY_CONFIGURED_TYPE))
+            {
+                zones[channel_idx].type                 = ZONE_TYPE_LINEAR;
+            }
+
+            if(!(zones[channel_idx].flags & ZONE_FLAG_MANUALLY_CONFIGURED_MATRIX_MAP))
+            {
+                zones[channel_idx].matrix_map.width     = 0;
+                zones[channel_idx].matrix_map.height    = 0;
+                zones[channel_idx].matrix_map.map.resize(0);
+            }
+
+            addressableCounter++;
        }

        unsigned int num_mainboard_leds = device_info.num_leds - device_info.num_headers;
-        for (unsigned int led_ch_idx = 0; led_ch_idx < zones[channel_idx].leds_count; led_ch_idx++)
+
+        for(unsigned int led_ch_idx = 0; led_ch_idx < zones[channel_idx].leds_count; led_ch_idx++)
        {
            unsigned led_idx = led_ch_idx + 1;
            led new_led;

            new_led.name = zones[channel_idx].name;
+
            if(device_info.device_type == AuraDeviceType::FIXED && led_ch_idx >= num_mainboard_leds)
            {
                new_led.name.append(", RGB Header ");
@@ -189,9 +218,10 @@ void RGBController_AuraUSB::SetupZones()
            {
                new_led.name.append(", LED ");
            }
+
            new_led.name.append(std::to_string(led_idx));

-            new_led.value = channel_idx;
+            new_led.value = (unsigned int)channel_idx;

            leds.push_back(new_led);
        }
@@ -200,17 +230,10 @@ void RGBController_AuraUSB::SetupZones()
    SetupColors();
 }

-void RGBController_AuraUSB::DeviceResizeZone(int zone, int new_size)
+void RGBController_AuraUSB::DeviceConfigureZone(int zone_idx)
 {
-    if((size_t) zone >= zones.size())
+    if((size_t)zone_idx < zones.size())
    {
-        return;
-    }
-
-    if(((unsigned int)new_size >= zones[zone].leds_min) && ((unsigned int)new_size <= zones[zone].leds_max))
-    {
-        zones[zone].leds_count = new_size;
-
        SetupZones();
    }
 }
@@ -24,7 +24,7 @@ public:

    void        SetupZones();

-    void        DeviceResizeZone(int zone, int new_size);
+    void        DeviceConfigureZone(int zone_idx);

    void        DeviceUpdateLEDs();
    void        DeviceUpdateZoneLEDs(int zone);
@@ -120,6 +120,7 @@
 #define AURA_TERMINAL_PID                                   0x1889
 #define ROG_STRIX_LC120_PID                                 0x879E
 #define AURA_RYUO_AIO_PID                                   0x1887
+#define AURA_RYUJIN_AIO_PID                                 0x18AE
 #define ASUS_ROG_ALLY_PID                                   0x1ABE
 #define ASUS_ROG_ALLY_X_PID                                 0x1B4C

@@ -416,7 +417,7 @@ REGISTER_HID_DETECTOR   ("ASUS Aura Addressable",                       DetectAs
 REGISTER_HID_DETECTOR   ("ASUS Aura Addressable",                       DetectAsusAuraUSBAddressable,   AURA_USB_VID, AURA_ADDRESSABLE_4_PID);
 REGISTER_HID_DETECTOR   ("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_1_PID);
 REGISTER_HID_DETECTOR   ("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_2_PID);
-REGISTER_HID_DETECTOR   ("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_3_PID);
+REGISTER_HID_DETECTOR_PU("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_3_PID,                           0xFF72, 0x00A1);
 REGISTER_HID_DETECTOR   ("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_4_PID);
 REGISTER_HID_DETECTOR   ("ASUS Aura Motherboard",                       DetectAsusAuraUSBMotherboards,  AURA_USB_VID, AURA_MOTHERBOARD_5_PID);

@@ -463,6 +464,7 @@ REGISTER_HID_DETECTOR_IP("ASUS ROG Gladius II Origin COD",
 REGISTER_HID_DETECTOR_IP("ASUS ROG Gladius II Wireless",                        DetectAsusAuraUSBMice,  AURA_USB_VID, AURA_ROG_GLADIUS_II_WIRELESS_1_PID,               1,  0xFF13);
 REGISTER_HID_DETECTOR_IP("ASUS ROG Gladius II Wireless",                        DetectAsusAuraUSBMice,  AURA_USB_VID, AURA_ROG_GLADIUS_II_WIRELESS_2_PID,               2,  0xFF01);
 REGISTER_HID_DETECTOR_IP("ASUS ROG Gladius III",                                DetectAsusAuraUSBMice,  AURA_USB_VID, AURA_ROG_GLADIUS_III_PID,                         0,  0xFF01);
+REGISTER_HID_DETECTOR_IP("ASUS ROG Gladius III Core",                           DetectAsusAuraUSBMice,  AURA_USB_VID, AURA_ROG_GLADIUS_III_CORE_PID,                    0,  0xFF01);
 REGISTER_HID_DETECTOR_IP("ASUS ROG Gladius III Wireless USB",                   DetectAsusAuraUSBMice,  AURA_USB_VID, AURA_ROG_GLADIUS_III_WIRELESS_USB_PID,            0,  0xFF01);
 REGISTER_HID_DETECTOR_IP("ASUS ROG Gladius III Wireless 2.4Ghz",                DetectAsusAuraUSBMice,  AURA_USB_VID, AURA_ROG_GLADIUS_III_WIRELESS_2_4_PID,            0,  0xFF01);
 REGISTER_HID_DETECTOR_IP("ASUS ROG Gladius III Wireless Bluetooth",             DetectAsusAuraUSBMice,  AURA_USB_VID, AURA_ROG_GLADIUS_III_WIRELESS_BT_PID,             0,  0xFF01);
@@ -523,6 +525,7 @@ REGISTER_HID_DETECTOR_PU("ASUS ROG PG32UQ",                             DetectAs
 REGISTER_HID_DETECTOR    ("ASUS ROG AURA Terminal",                     DetectAsusAuraUSBTerminal,      AURA_USB_VID, AURA_TERMINAL_PID);
 REGISTER_HID_DETECTOR_PU ("ASUS ROG Strix LC",                          DetectAsusAuraUSBROGStrixLC,    AURA_USB_VID, ROG_STRIX_LC120_PID,                          0x00FF, 1);
 REGISTER_HID_DETECTOR_PU ("ASUS ROG Ryuo AIO",                          DetectAsusAuraUSBRyuoAIO,       AURA_USB_VID, AURA_RYUO_AIO_PID,                        0xFF72, 0x00A1);
+REGISTER_HID_DETECTOR_PU ("ASUS ROG Ryujin AIO",                        DetectAsusAuraUSBRyuoAIO,       AURA_USB_VID, AURA_RYUJIN_AIO_PID,                     0xFF72, 0x00A1);
 REGISTER_HID_DETECTOR_I  ("ASUS ROG Throne",                            DetectAsusAuraUSBHeadsetStand,  AURA_USB_VID, AURA_ROG_THRONE_PID,                          0);
 REGISTER_HID_DETECTOR_I  ("ASUS ROG Throne QI",                         DetectAsusAuraUSBHeadsetStand,  AURA_USB_VID, AURA_ROG_THRONE_QI_PID,                       0);
 REGISTER_HID_DETECTOR_I  ("ASUS ROG Throne QI GUNDAM",                  DetectAsusAuraUSBHeadsetStand,  AURA_USB_VID, AURA_ROG_THRONE_QI_GUNDAM_PID,                0);
@@ -117,6 +117,8 @@ RGBController_AsusROGAlly::RGBController_AsusROGAlly(ROGAllyController* controll

 RGBController_AsusROGAlly::~RGBController_AsusROGAlly()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -129,6 +129,8 @@ RGBController_AsusROGStrixLC::RGBController_AsusROGStrixLC(AsusROGStrixLCControl

 RGBController_AsusROGStrixLC::~RGBController_AsusROGStrixLC()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -283,6 +283,8 @@ RGBController_AsusCerberusKeyboard::RGBController_AsusCerberusKeyboard(AsusCerbe

 RGBController_AsusCerberusKeyboard::~RGBController_AsusCerberusKeyboard()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -165,6 +165,8 @@ RGBController_AsusSagarisKeyboard::RGBController_AsusSagarisKeyboard(AsusSagaris

 RGBController_AsusSagarisKeyboard::~RGBController_AsusSagarisKeyboard()
 {
+    Shutdown();
+
    delete controller;
 }

@@ -89,7 +89,7 @@ void AsusMonitorController::SetDirect(std::vector<RGBColor> colors)
    usb_buf[0x00] = 0xEC;
    usb_buf[0x01] = 0x40;
    usb_buf[0x02] = 0x84;
-    usb_buf[0x04] = colors.size();
+    usb_buf[0x04] = (uint8_t)colors.size();

    for(size_t i = 0; i < colors.size(); i++)
    {
@@ -22,8 +22,12 @@
 | Product ID                                                |
 \*---------------------------------------------------------*/
 #define ASUS_ROG_STRIX_XG27AQDMG_PID                   0x1BA3
-#define ASUS_ROG_SWIFT_XG27UCG_PID                     0x1BB4
+#define ASUS_ROG_STRIX_XG27ACDNG_PID                   0x1BC9
+#define ASUS_ROG_STRIX_XG27UCG_PID                     0x1BB4
 #define ASUS_ROG_SWIFT_PG32UCDM_PID                    0x1B2B
+#define ASUS_ROG_SWIFT_PG32UCDMR_PID                   0x1C9B
+#define ASUS_ROG_SWIFT_PG32UCDP_PID                    0x1BCA
+#define ASUS_ROG_AURA_MONITOR_LIGHT_BAR_PID            0x1AC8

 DetectedControllers DetectAsusMonitorControllers(hid_device_info* info, const std::string& name)
 {
@@ -44,5 +48,13 @@ DetectedControllers DetectAsusMonitorControllers(hid_device_info* info, const st
 }

 REGISTER_HID_DETECTOR_IPU("Asus ROG STRIX XG27AQDMG",   DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_STRIX_XG27AQDMG_PID,   1, 0xFF72, 0x00A1);
-REGISTER_HID_DETECTOR_IPU("Asus ROG STRIX XG27UCG",     DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_SWIFT_XG27UCG_PID,     1, 0xFF72, 0x00A1);
-REGISTER_HID_DETECTOR_IPU("Asus ROG STRIX PG32UCDM",    DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_SWIFT_PG32UCDM_PID,    1, 0xFF72, 0x00A1);
+REGISTER_HID_DETECTOR_IPU("Asus ROG STRIX XG27ACDNG",   DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_STRIX_XG27ACDNG_PID,   1, 0xFF72, 0x00A1);
+REGISTER_HID_DETECTOR_IPU("Asus ROG STRIX XG27UCG",     DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_STRIX_XG27UCG_PID,     1, 0xFF72, 0x00A1);
+REGISTER_HID_DETECTOR_IPU("Asus ROG SWIFT PG32UCDM",    DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_SWIFT_PG32UCDM_PID,    1, 0xFF72, 0x00A1);
+REGISTER_HID_DETECTOR_IPU("Asus ROG SWIFT PG32UCDMR",   DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_SWIFT_PG32UCDMR_PID,   1, 0xFF72, 0x00A1);
+REGISTER_HID_DETECTOR_IPU("Asus ROG SWIFT PG32UCDP",    DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_SWIFT_PG32UCDP_PID,    1, 0xFF72, 0x00A1);
+/*---------------------------------------------------------*\
+| ALB01 exposes the Aura HID collection on interface 2.     |
+\*---------------------------------------------------------*/
+REGISTER_HID_DETECTOR_IPU("Asus ROG Aura Monitor Light Bar", DetectAsusMonitorControllers, ASUS_VID, ASUS_ROG_AURA_MONITOR_LIGHT_BAR_PID, 2, 0xFF72, 0x00A1);
+
@@ -46,6 +46,8 @@ RGBController_AsusMonitor::RGBController_AsusMonitor(AsusMonitorController* cont

 RGBController_AsusMonitor::~RGBController_AsusMonitor()
 {
+    Shutdown();
+
    delete controller;
 }

--- a/Show More
+++ b/Show More